Networing RC-415/RC-416
USER’S Manual
Networing RC-415/416
USER’S Manual
FCC Certifications
This Equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received; including interference that may cause
undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class A for ITE, the
essential protection requirement of Council Directive 89/336/EEC
on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it
may be possible that information in this document is not
up-to-date. Please check with your local distributors for the latest
information. No part of this document can be copied or reproduced
in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of Rosewill.
Copyright © 2010, All Rights Reserved.
1
Networing RC-415/416
USER’S Manual
Introduction
The device is a powerful, high-performance Gigabit Ethernet
switch, with all ports capable of 10, 100 or 1000Mbps
auto-negotiation operation (NWay), which means the switch could
automatically negotiate with the connected partners on the network
speed and duplex mode. It is ideal for micro-segmenting large
networks into smaller, connected subnets for improved
performance, enabling the bandwidth demanding multimedia and
imaging applications. Moreover, the 10/100/1000Mbps
auto-sensing ability provides an easy way to migrate 10/100Mbps
to 1000Mbps network with no pain. Compared to the shared
10Mbps or 100Mbps networks, the switch delivers a dedicated
10/100/1000Mbps connection to every attached client with no
bandwidth congestion issue. This switch also supports auto MDI /
MDI-X function. Each port could be used to connect to another
switch or hub with no crossover RJ-45 cable.
Store-and-forward switching mode promises the low latency plus
eliminates all the network errors, including runt and CRC error
packets. To work under full-duplex mode, transmission and
reception of the frames can occur simultaneously without causing
collisions as well as double the network bandwidth.
The switch provides 9K bytes jumbo frames. With the Jumbo frame
function, you can get better network performance, because the
switch can send more data at the same time.
The switch is plug-n-play without any software to configure and
also fully compliant with all kinds of network protocols.
Before you start to install the switch, check the following contents
in this package
• One Gigabit Ethernet switch (RC-415 5 port gigabit switch/
RC-416 8 port gigabit switch)
• One power adapter
• User’s manual
：
2
Networing RC-415/416
LED Definition
Please refer to the following table for LED definition:
1 2 3 4 5
POWER
RC-415
5-port Gigabit Switch
RC-416
8-port Gigabit Switch
POWER
LED Status Operation
Steady Green
Power
Link/ACT
Off
Steady Green
Blinking Green
LINK/ACT
1 2 3 4 5 6 7 8
Power is on
Power is off
Port connected
The port is transmitting/receiving data
USER’S Manual
LINK/ACT
3
Networing RC-415/416
USER’S Manual
Stations Connection
Connect each station to the switch by twisted-pair cable. Plug one
RJ-45 connector into a RJ-45 port of the switch, and plug the other
RJ-45 connector into the station’s network adapter. Power on the
switch and then system is ready.
For cable selection, refer to the following table.
Switches Connection
In making a switch interconnection, you could use any port to
connect another switch with straight or crossover cable. As all the
ports support auto MDI / MDI-X function, using a straight cable to
make a switch-to-switch connection is allowed.
For cable selection, refer to the following table
Network Speed Cable Type Max.Length
10Mbps
100Mbps
1000Mbps
Cat. 3, 4, 5 UTP/STP
Cat. 5 UTP/STP
Cat. 5 UTP/STP
：
100 meters
100 meters
100 meters
4
Networing RC-415/416
IEEE 802.3 10BASE-T
Standard
Interface
MAC Addr.
Thank you for purchasing a quality Rosewill Product.
Please register your product at : www.rosewill.com for
complete warranty information and
future support for your product.
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x full duplex operation and flow control
IEEE 802.3az Draft Energy Efficient Ethernet
RC-415 - 5* 10/100/1000Mbps RJ-45 Gigabit
Ethernet ports
RC-416 - 8* 10/100/1000Mbps RJ-45 Gigabit
Ethernet ports
Uplink
Auto MDI/MDI-X（Auto crossover
10/100/1000Mbps & Full/Half duplex mode auto
Network
Speed
detection (1000Mbps for Full duplex only)
RC-415 - 8K MAC entries
Table
RC-416 - 8K MAC entries
RC-415 - 1M bits
Buffer
Memory
RC-416 - 1M bits
Jumbo
9K bytes
Frame
RC-415: External Power Adapter 5V 1A
Power
Supply
RC-416: External Power Adapter 5V 1A
CE, FCC and VCCI class A
EMI
USER’S Manual
）
5
Loading...