Page 1
CASE 5600 Series
USER Manual
www.rosewill.com
Page 2
CASE 5600 series
User Manual
1
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Contents
Configuration
Features Descriptions
Installation
1. Opening Chassis
2. Installing Motherboard
3. Installing 3.5" HDD
4. Installing 5.25" Device
5. Installing Add on Card
6. Installing Floppy
7. Cleaning Filters-Air guide Filter
8. Cleaning Filters-Front panel Filter
9. USB port
10. IEEE1394 Port
11. Audio Port
12. System Control Connectors
Information
P. 2
P. 3
P. 5
P. 6
P. 8
P. 9
P. 1 0
P. 1 1
P. 1 3
P. 1 3
P. 1 4
P. 1 5
P. 1 8
P.16
P.17
Page 3
CASE 5600 series
User Manual
2
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Confi guration
Dimension
(W x H x D )
M/B Size
Drive Bay
Expansion Slots
Thermal Solution
Air Filter
I/O Port Bracket
Megal Material
7.9" x 17.3" x 19.4"
ATX, Micro ATX
External : 4 x 5.25" + 2 x 3.5"
Internal : 5 x 3.5"
7Slots
1 x 12 cm fan in rear and 1 x 12 cm fan holder in front
One air fi lter on the front panel ( only in R6A34)
Supports one I/O port bracket for standard ATX M/B
0.8 mm thickness SECC rustproof & galvanized JIS Steel
Page 4
CASE 5600 series
User Manual
3
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Features Descriptions
Front 120mm Fan Rear 120mm Fan Sliding Rails for 5.25"
device
Sliding Rails for 3.5" HDD
Screw-less Add-on Card
assembly
Door opening up to 270
Degree
Easy-clean fi lter
(in left side panel)
Easy-clean fi lter
(in front panel)
Page 5
CASE 5600 series
User Manual
4
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Screw-less and lockable
left side panel
Adjustable air inflow Front IO Ports Convenient Accessory box
Page 6
CASE 5600 series
User Manual
5
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Installation
1.Opening Chassis
1.1
Take off the thumb screws on the back plane
1.2
Push the Key-button
1.3
Roll the side cover anticlockwise to open
1.4
Push hooks marked in red circle to detach the
front panel from the chasis
Page 7
CASE 5600 series
User Manual
6
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
2.1
Due to our special design of
motherboard stand-off,copper
motherboard stand-off not needed
when you install the ATX motherboard.
2.2
Sit the motherboard on our special
motherboard stand-off and screw in all the
screws into the motherboard stand-offs.
2.Installing Motherboard
ATX Motherboard
Special motherboard stand-off
NOTE : The copper motherboard stand-off not
needed when you install the ATX motherboard.
DON'T SCREW THE COPPER MOTHERBOARD
STAND-OFF INTO THE SPECIAL MOTHERBOARD
STAND-OFF OR MOTHERBOARD INSTALLING
CAN'T BE PROCESSED SUCCESSFULLY.
Page 8
CASE 5600 series
User Manual
7
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Micro ATX Motherboard
2.1
Locate and align the screw holes on the
motherboard and chasis; place the
motherboard at the correct position,
and then screw copper motherboard standoffs brass studs onto chassis's metal shell.
Note: Screw holes marked with "M" are
motherboard stand-off positions for micro
ATX motherboard.
2.2
Sit the motherboard on themotherboar
stand-offs and screw in all the screws
into the motherboard stand-offs.
Page 9
CASE 5600 series
User Manual
8
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
3.Installing 3.5" HDD
3.1
Insert the screw into the rubber pad hole on the rail
3.2
Attach rails to bothe sides of
your HDD
3.3
Insert the railed HDD into the 3.25" HDD bay and push to the buttom
NOTE : Screws for HDD have no
thread, no screwdriver needed
when you work step 3.2
Page 10
CASE 5600 series
User Manual
9
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
4.1
Disassemble the front panel (please refer to step 1.4 )
4.2
Attach rails to both sides of your 5.25" device
PS: You can also fasten rails on your 5.25" device by screws
4.3
Insert the railed 5.25" device into the 5.25"
drive bay
4.Installing 5.25" Device
Page 11
CASE 5600 series
User Manual
10
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
5.Installing Add on Card
5.1
Push out to loosen add on card kit
5.2
Insert your add on card into the right slot
5.3
Push down add on card kit to fasten the add
on card
Page 12
CASE 5600 series
User Manual
11
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
6.Installing Floppy
6.1
Detach the front panel
(Please refer to Step 1.4, Page 5)
6.2
Unscrew the screws holding the
fl oppy cage
6.3
Slide out the fl oppy cage
6.4
Remove the metal cover
Page 13
CASE 5600 series
User Manual
12
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
6.5
Secure the fl oppy on cage by
screws
6.6
Slide the fl oppy cage back
6.7
Secure the fl oppy cage by
screws
6.8
Attach the front panel
Page 14
CASE 5600 series
User Manual
13
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
7.Cleaning Filters - Air Guide Filter
7.1
Turn anticlockwise to take off the fi lter
8.Cleaning Filters - Front panel Filter
8.1
Push front panel hooks to detach
the front panel from the chassis
( please refer to step 1.4 )
8.2
Detach the fi lter from the front
panel
Page 15
CASE 5600 series
User Manual
14
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
9.USB Port
NOTE :
1.Make sure that your motherboard offers USB interface. NOT every motherboard offers it.
2.NEVER connect a IEEE1394 connector to the USB pins. It will damage the motherboard.
9.1 Read your motherboard’s user manual to find the pins for the USB connector.
9.2 Find the USB connector and connect it to the pins.
USB+5V
M/B USB PINS
USB_P5 -
USB_P5 +
GND
USB+5V
USB_P8 USB_P8 +
GND
ON
Page 16
CASE 5600 series
User Manual
15
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
10.IEEE1394 Port
NOTE :
1.Make sure that your motherboard offers IEEE1394 interface. NOT every motherboard offers it.
2.NEVER connect a USB cable to the IEEE1394 connectors. It will damage the motherboard.
10.1 Read your motherboard’s user manual to find the pins for the IEEE1394 connector.
10.2 Find the IEEE1394 connector and connect it to the pins.
TPA2+
GND
TPB2+
+12V
M/B IEEE1394 PINS
GND
+12V
TPB2
GND
TPA2
Page 17
CASE 5600 series
User Manual
16
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
11.Audio Port
MIC2
MICPWR
Line out_R
NC
Line out_L
AGND
+5VA
Bline_out_R
Bline_out_L
NOTE :
Make sure that your motherboard offers Audio interface for front panel. NOT every motherboard offers it.
10.1 Read your motherboard’s user manual to find the pins for the Audio connector.
10.2 Find the Audio connector and connect it to the pins.
M/B Audio PINS
Page 18
CASE 5600 series
User Manual
17
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
12.System Control Connectors
1. Read your motherboard’s user manual to find the pins for these system control connectors.
2. Refer to your motherboard’s user manual to connect these connectors correctly.
PLED+
PLED-
IDE_LED+
IDE_LED-
PWA
Ground
Reset
Ground
Ground
Ground
Speaker
+5V
PLED
PWR
RESETIDE_LED
SPEAKER
System Warning Speaker
ATTENTION :
The diagram is just an example.
NOT every motherboard has the same
layout of these system control pins.
Please refer to your motherboard
user’s manual to check the layout
before the installation.
Connectors
ATX Power Switch
Reset Switch
System Power LED
HDD Activity LED
Page 19
CASE 5600 series
User Manual
18
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Thank you for purchasing a High-Quality Rosewill Product.
Please register your product at : www.rosewill.com
for complete warranty information and future support for your product.
If you have any question while using our products, please visit our website : www.rosewill.com
for latest driver & user manual or feel free to contact us at feedback@rosewill.com
Support Phone Number: 800-575-9885
Support Email: techsupport@rosewill.com
Page 20
www.rosewill.com
Loading...