Rosen Entertainment Systems DS-TY0820 User Manual

Installation Guide

NOTICE OF INTENDED INSTALLATION AND USE E

THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS

NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE

VEHICLE IS IN MOTION THROUGH A CONNECTION TO THE PARKING BRAKE. THE INSTALLER OF

THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS WORKING PROPERLY PRIOR TO

DELIVERY OF THE VEHICLE. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR

INTERFERE WITH SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY

OR DEATH, AND COULD ALSO VIOLATE STATE AND/OR FEDERAL LAW.

ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR

PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION

AND/OR USE.

BEFORE YOU START THE INSTALLATION, READ THIS GUIDE!

Rosen Multi-Media systems are the easiest-to-install OEM Radio replacement systems available today.

However, we strongly recommend reading this guide before starting the installation!

For additional technical tips, please visit

www.Rosendealercentral.com

1 - Make sure you have the tools you will need

These common items are needed to complete this installation:

· Digital multi-meter (DMM) · #2 Phillips screwdriver · Panel removing tools

1/4” drive sockets are often needed for dashboard and trim disassembly

Torx or Allen-drive wrenches if they are used on any panels you will be removing

A DVD or CD

Standard installation parts you may need include wire, wire ties, wire crimp connectors or solder, electrical insulating tape, and foam tape. Installation of aftermarket automotive electronics also often requires access to special parts. It is a good idea to have a source for these common installation parts.

in good condition

for testing the system

DS-TY0820 Toyota Corolla

Installation Guide Toyota Corolla

2 - Inspect the vehicle and plan your work

CHECK THE BATTERY

Test the battery voltage to make sure it’s fully charged and inspect battery terminals for tightness and any corrosion. This only takes seconds and can save hours of troubleshooting later.

New Vehicles RARELY have a fully charged battery. This can cause many system malfunctions.

3 – Turn the Vehicle OFF or Disconnect the Battery

TURN THE VEHICLE OFF BEFORE STARTING

Be sure to turn the vehicle OFF before starting, and keep the vehicle OFF until the installation is fully completed BEFORE the vehicle is turned on.

: Failure to follow these instructions may cause the AIRBAG FAULT SENSOR to become enabled. Fault

Note

Sensors which have been enabled will require the Dealer Service Department to reset them. Dealerships often charge a significant fee to reset the Fault Sensor.

Keep the Vehicle OFF while the Radio is disconnected to avoid a potential Airbag Sensor Fault

4 – Remove the Interior Trim Components

You will need to remove the interior trim components prior to removing the factory radio. The following steps will help guide you through this process.

Note: When removing the Interior Trim Components, use caution to prevent damage to the components. If you are unsure about the removal process, consult the OEM Service Manual for additional instructions.

Note: Once the Interior Trim Components have been removed, be sure to inspect the clips for any damage. Damaged part must be replaced before re-installation.

Step 1: Remove the Upper Trim

Components

Step 2: Remove the Lower Trim

Components

Step 3: Remove the Vent Trim

Component

Step 4: Unplug the Electrical

Connection

Use Caution. See the OEM Service Manual for additional information on the removal process

Page 2

Installation Guide Toyota Corolla

5 - Remove the Factory Radio

You will need to remove the Factory Radio and prepare the Rosen Multi-Media unit for installation. The following steps will help guide you through this process.

Note: Be sure to inspect all brackets and clips to ensure they were not damaged during the removal process. If any brackets or clips were damaged, replace them prior to installation of the Rosen unit.

Step 1: Remove the Mounting

Screws

Step 2: Unplug the Electrical

Connections

Step 3: Remove the Factory

Brackets and Clips

Step 4: Reinstall the Factory

Brackets and Clips on the Rosen Unit

Use Caution. See the OEM Service Manual for additional information on the removal process

6 – Locate the GPS Antenna, Optional XM Antenna and iPod Interface

You will need to mount the GPS and Optional XM Antennas on the exterior of the vehicle. And mount the iPod Interface Connector in the vehicle. The following steps will help guide you through this process.

Note: Please route the GPS harness away from other power harnesses in the vehicle. This will help to ensure optimum performance of the GPS system.

Note: Please locate the iPod interface module in an area which can be serviced in the future. The iPod cable is intended to be a serviceable item, which plugs into the iPod/XM Interface Module.

Step 1: Mount the GPS and XM

antenna in a location on the exterior of the Vehicle

Step 2: Connect the Optional XM

Tuner as shown below. Mount the tuner inside the vehicle

Step 3: Mount the iPod/XM

Interface module where it can be serviced in the future

Step 4: Locate the iPod interface

connector for use by the end-consumer

It is the installer’s responsibility to ensure that the safety equipment in the vehicle is NOT adversely affected by installation of this system. Ensure that the routing of the harnesses does NOT obstruct airbags, SRS or other safety devices.

Page 3

+ 5 hidden pages