Rosen Entertainment Systems AV7800 User Manual

NOTICES

NOTICE OF INTENDED USE

Our systems are designed to enable viewing of video

ONLY for rear-seat occupants, and are not intended for

viewing by the driver when the vehicle is in motion. Such

use might distract the driver or interfere with the driver’s

safe operation of the vehicle, and thus result in serious

injury or death. Such use might also violate state or local

laws.

Manufacturer disclaims any liability for any bodily injury

or property damage that might result from any improper or

unintended use.

About the Registered Marks

This item incorporates copy protection technology that is protected by U.S. patents
and other intellectual property rights of Rovi Corporation. Reverse engineering and

disassembly are prohibited.

NOTE: Features and specications listed in this manual are subject to change

Manufactured under license from Dolby Laboratories.“Dolby” and the double-D

symbol are trademarks of Dolby Laboratories.

DivX Certied products (if equipped): “Divx, DivX Certied, and associated logos

are trademarks of DivX, Inc. and are used under license.”

without notice

Table of Contents

Getting Started…………………………………………………………………………………………………………………………………............…………………...6

Introduction ……………………..........……………………………………………………………………………………………………………………………………..8

Discs Compatibility………………….……………………………………………………………………………………..........………………………………………….9

Changing and Adjusting Display Settngs…………………………………………………………………………………………………………..........……….……..10

Using the Remote Control…………………………………………………………………………………………………………………………..........……….………11

Basic Remote Control Buttons……………………………………………………………………………………………………………………..........……….………12

Using Menu and Navigation Buttons, Using Audio Buttons……………………………………………………………………………………..........………………13

Using DVD Disc Features…………………………………………………………………………………………………………………………….........…….……….14

Replacing the Remote Battery……………………………………………………………………………………………………………………….........…….……….14

CD Audio and MP3 Playback………………………………………………………………………………………………………………………………...........……..15

Listening Over the Car Speakers...………………………………………………………………………………………………………………….............……..……15

Using the Included 2 Channel Wireless Headphones………………………………………………………………………………………………...........………….16

Replacing the Headphone Batteries ………………………………………………………………………………………………....................................………….16

Using the Integrated Game System……………………………………………………………………………………………………………………...........………...17

Using External Sources…………………………………………………………………………………………………………………………………..........……...….17

DVD Setup and Conguration.……………………………………………………………………………………………………………………………..........…..…..18

Frequently Asked Questions……………………………………………………………………………………………..…………………………..........……………..19

AV7800 Owner’s Manual

GETTING STARTED

Use the system with the vehicle running or with the ignition key switch in the “accessory” position.

Make certain that the remote, the headphones, and the game controller have fresh batteries and are properly installed.

To switch the system on, press the power button on the unit or remote control. Each headrest must be turned on independently.

The Front Panel Controls

DVD Slot (Label facing away from you)

Fast Forward/
Navigation Up

Power

USB
(Side of the unit)

Play/Pause

Mode/Source

Speaker Control

AUX/AV Input
(Side of the unit)

Power Button

6

Previous Chapter or
Track/Navigation Left

Fast Rewind/
Navigation Down

Enter

Next Chapter or
Track/Navigation
Right

To Watch a DVD:

1 Power the system on, unit will default to DVD player and resume play,
if a disc is present.
2 Press EJECT to remove any loaded disc.
3 Insert a DVD with the label facing away from you.

4 Most DVD discs begin playback
automatically. If a menu appears,
press PLAY or ENTER as instructed
on the screen.

To Play the Integrated Video Game:

1 Press MODE until “INTERNAL GAME”
appears on the screen.
2 Turn the game controller on by setting
the game switch to A or B.
3 Use the arrow keys on the game controller to select a game.
4 Press the START button on the game controller. (see page 17 for more

information)

5 Remember to turn the controller “OFF” when not in use.

To View Same Image on both Screens:

1 Press MODE until “Second Unit” appears on the screen. Your

monitor will now display the same image as the other unit.

To Use An External Video Source

1 Connect the RCA audio and video outputs of the device to the RCA

adapter cable. Plug into AUX input port on front of monitor.

2 Press MODE (SOURCE on the remote) until “AUX 1” appears on the

screen.

Listening Over the Vehicle Speakers

1 Make sure MUTE is off. Press SPEAKER button on the front panel of the

system or the remote control and “SPEAKER SOUND ON FM _
_ . _ PRESS LEFT OR RIGHT TO ADJUST” will appear. (This must be
done each time the system is used.)

2 Turn on the car radio. Tune to the FM frequency displayed on the

screen. If radio interference is heard, try another frequency. (see pages
13 and 15 for more information)

7

AV7800 Owner’s Manual

INTRODUCTION

Congratulations on purchasing a Rosen DVD Entertainment System!
Here’s a list of some things you can do with your system:

· Play DVD movies, music CDs, or discs with MP3 audio les.

· Play onboard video games.

· Play audio through the vehicle speakers or the wireless headphones

· Use external audio/video inputs from video game consoles,
camcorders, or optional units like a TV tuner or a DVD changer.

· View JPG photo les or playback compatible MPG videos using the

DVD or USB memory slot. Maximun USB size is 2GB.

· Ofcial DivX Certied Product.

· Plays all versions of DivX video (including DivX 6) with standard

playback of DivX media les.

Precautions

In order to operate the system, the
vehicle ignition key switch must be

in the ACC or engine ON position.

ACC or engine
ON position

• Use this system only if properly installed by a qualied installer.

• If the unit shows any sign of malfunction, turn it off and consult your

dealer immediately. Do not open the unit - there are no serviceable
parts inside.

• Do not press directly on the display surface - you may damage

it.

• Clean the display surface with a slightly damp, soft cloth using

household glass cleaner. Do not use solvents such as benzene,
thinner, or commercial cleaners.

• When using portable radios and telephones near the system, pic-

ture or sound interference may occur.

• If your car was parked in a very cold or very hot place, you may see

a blank screen, distorted picture or the unit may not be able to load
a disc. The system will return to normal after the unit temperature
returns to a normal operating range. This may take more than an
hour depending on the temperature.

• If your car battery charge is low or the vehicle battery is old, you

may see a blank screen, distorted picture or the unit may not be
able to load a disc. The system will return to normal after the unit
voltage returns to a normal operating range.

Note: The system’s operating voltage range is
11-16VDC operating voltage. The system oper­ating temperature is 32o to 140o F ( 0o to 60o C).
Use of the system beyond the safe operating
ranges listed, can cause temporary or perma­nent damage to the unit, and such damage
may not be covered by the manufacturer’s
warranty.

8

DISC COMPATIBILITY

Compatible Discs

Note: Not all discs are supported by this system. You may nd a
disc that will not play on this system, but works ne on other players.

Various manufacturers of discs change technology from time to time
which may create compatibility issues. This is not a probelm with the
unit and is not covered by warranty.

Most DVD and CD-Audio discs are compatible with the AV7800
system.

The unit can also play most CD-Recordable discs containing CD-Au-

dio, MP3 les, and JPEG images - but not all such discs. Since these

discs are usually made on home computers, there is no certica­tion process ensuring that all such discs play on all players.

DVD Regions

When a DVD disc is created, it is encoded with a “Region number.”
The disc will only play on DVD players with the same Region number ­for instance, a Region 3 disc won’t play on a Region 1 player.

Region 1: U.S. and U.S. Territories, Canada
Region 2: Japan, Western Europe, Middle East, South Africa
Region 3: South Korea, Hong Kong, Taiwan, Southeast and East Asia

Region 4: New Zealand, Australia, Pacic Islands, Mexico, Central/

South America
Region 5: Russia and the former Soviet Union, Africa, Indian
subcontinent, North Korea
Region 6: China

Incompatible Discs

The following disc types are incompatible with the system:

· DVD-ROM/DVD-RAM/DVD+RAM discs.

· Most DVD-R/DVD-RW/DVD+R/DVD+RW discs.

· Some Photo CDs.

· CD-ROM data discs.

· BlueRay discs.

· CD-Audio discs made with certain copy protection methods.

· Any DVD with a different Region number than the unit.

· Any disc that does not meet DVD Forum standards.

Why the system doesn’t respond the same way to all discs

When a DVD disc is created, the creator has to dene how the disc

will operate when loaded into a DVD player. For instance, some discs
begin playing immediately, while other discs only display a menu and
require a menu selection to be made before playback will start.

The DVD standard also allows the maker of a DVD disc to disable
functions at certain times, such as Fast-Forward and Stop (which is
why you can’t skip past the copyright warning screen). If some DVD
feature temporarily isn’t working for you, usually the disc is preventing
the player from performing that function.

Discs that don’t properly load and play

Some CD and DVD discs, especially homemade discs which do not
have all the data needed to properly initialize all DVD players, may not
load and play properly. They may even create a state where the DVD
player will not eject the disc at all.

9

AV7800 Owner’s Manual

CHANGING AND ADJUSTING THE DISPLAY

Selecting a display mode: The system’s “widescreen” display has
a 16:9 aspect ratio - wider than a standard television. While many

DVDs provide widescreen video images that t the screen, standard

broadcast TV and many video games do not.

• To view a widescreen DVD, press the DISPLAY button on the

remote until “WIDE” is displayed on the screen.

• To watch a fullscreen DVD, the internal game system, or

broadcast television, select “STANDARD.”

Change the Display Adjustments Remote Control Only: The
display has adjustable video settings. To change these settings, press
and hold the DISPLAY button on the remote control to bring up the
following menu:

BRIGHTNESS 32

CONTRAST 32
COLOR 32
TINT 32

To select a setting to be changed: Press the DOWN arrow button to
move the cursor down the menu list. Once you have selected the item
to change, use the LEFT and RIGHT arrows on the remote or the

front panel to adjust the settings. After you have nished making your

desired changes, press the DISPLAY button on the remote to exit and
save the changes you have made.

To change the value of a setting: Use the LEFT and RIGHT arrow but-
tons. The range is from 0 to 63.

To exit the menu: Press the DISPLAY button to save settings and exit.

Set the brightness level in daytime conditions with plenty of ambient
light. You can use the Day/Night mode button to switch between Day
and Night modes.

Note: The internal DVD player can be congured for either a

16:9 “Wide” image output or a 4:3 “Standard” image output.

Since the unit has a wide screen display, the DVD player should
be congured for “Wide.” For more information, see page 19.

Note: The internal DVD player also has a set of video adjust­ments, which are separate from the main adjustments.

10

USING THE REMOTE CONTROL

You can use the remote control to operate the system, including
access to features not available on the front panel. The unit has an
infrared sensor to receive signals located in the control panel. For

denitions of each remote control button’s specic function, see the

following pages.

1 Power 15 Info Menu
2 Pause/Frame Step 16 Zoom
3 Stop 17 Navigate Left
4 Play 18 Enter
5 Previous Chapter/Track 19 Navigate Right
6 Fast Reverse 20 Display
7 Fast Forward 21 Setup
8 Next Chapter/Track 22 Navigate Down
9 Speaker Sound Control 23 Disc Menu
10 RES Sound (not active) 24 Day/Night Mode
11 Mute 25 Repeat
12 Eject (Not Active) 26 Subtitle
13 Source
14 Navigate Up

Note: If you try to perform a DVD action when it is not permit­ted (such as accessing the disc menu while the disc is loading),

there will be no response from the unit. This is normal operation
and is not a problem with your system.

6

22

3 2

7

11

15

19 18

23

8

12

16

20

24

1 4

5

10

9

14 13

17

21

25

26

11

AV7800 Owner’s Manual

BASIC REMOTE CONTROL BUTTONS

1 Power

Pressing this button powers on the unit. This button also powers on the
optional external source unit.

4 Play

Press to begin or resume playback of a DVD.

Note: When the disc is rst inserted, you may have to press

PLAY or ENTER to begin playback.

3 Stop

Press once to temporarily stop playback of a DVD. To resume normal
playback from the same point, press PLAY.

To play the disc from the beginning, press STOP twice, then PLAY.

Note: Once STOP is pressed twice, the player can only begin
playing from the beginning of the disc.

5 Previous Chapter/Track

Press to jump to the previous title or chapter if available on a DVD, or
to the previous track on an audio CD. Not supported with some VCDs.

8 Next Chapter/Track

Press to jump to the next title or chapter if available on a DVD, or to the
next track on an audio CD. Not supported with some VCDs.

6 Fast Reverse

Press to search in reverse. To resume normal playback, press PLAY.
Press the REVERSE button multiple times to adjust search direction
and speed. Choose from 2, 4, 8, and 16x. Press PLAY to resume

regular play.

7 Fast Forward

Press during playback to fast forward. Press the FAST FORWARD but-
ton multiple times to adjust search direction and speed. Choose from
2, 4, 8, and 16x. Press PLAY to resume regular play.

2 Pause/Frame Step

Press once to pause playback. Press repeatedly to advance video
frame by frame. To resume normal playback, press PLAY.

12

24 Day/Night Mode

This button decreases display brightness for optimum viewing in low
light conditions. For more information, see page 10.

USING MENU AND NAVIGATION BUTTONS

13 Source

This button allows you select the Internal DVD/CD player, the Internal
Game, the Second Unit, or the Auxiliary Input. You can also select the
optional TV Tuner, DVD changer, or other optional auxiliary sources, if
installed.

Note: The Mode button on the control panel performs the same
function.

14, 22 Up/Down Navigation Arrows

Press to move up or down in a menu or to change channels when
watching TV.

17, 19 Left/Right Navigation Arrows

Press to move left or right in a menu. Also used to change frequencies
on the FMT, after the Speaker Sound button is pressed.

18 Enter

Press to make a menu selection.

21 Setup

Pressing this button brings up the DVD player setup screen.

15 Info Menu

Pressing this button brings you into the DVD player menu.

SOURCE

SETUP

USING AUDIO BUTTONS

9 Speaker Sound Control

When this button is pressed, “Speaker Sound On” appears on the
screen, along with the FM frequency to which you should tune your
radio, such as “FM 88.1.” To change the frequency, press the LEFT or
RIGHT arrow buttons on the remote control and wait two seconds for
the station to set. Headphone audio is not affected by this button.

FM frequencies available: Find a frequency in your geographic location
that has no static transmission and set it.

Note: If the frequency does not appear on screen when this
button is pressed, an external FM Modulator is probably being

used. See page 15 for more information.

11 Mute

Press once to mute all system audio. As long as the Mute function is
active, “Mute” will appear on the screen. Press again to turn Mute off.

13

AV7800 Owner’s Manual

USING DVD DISC FEATURES

23 Disc Menu

Press to see the main menu for the DVD being played. To resume
normal playback, press PLAY.

DISC

MENU

CHANGING THE SHAPE AND SIZE OF THE IMAGE

+

16 Zoom

View the same scene on a DVD at different magnications.

1 Press the ZOOM button during playback to select among the follow-

ing options: Zoom 1, Zoom 2, Zoom 3, and Off.

2 To resume normal playback, press ZOOM until “Zoom off” is dis-

played.

20 Display

This button allows you select from the various screen display modes.

+

DISPLAY

• To view a widescreen DVD, press this button until “WIDE” is

displayed on the screen. This uses the full width of the screen.

• To watch a fullscreen DVD or broadcast television, press until

“STANDARD” is displayed. This mode uses most of the screen,
but black bars will be visible on the sides, like this:

• To adjust the display settings (color, contrast, etc.), press and hold

the DISPLAY button for two seconds.

For more information about image shapes, see “Managing Black Bars,”
on page 18.

25 Repeat

This button enables chapter and title repeat.

26 Subtitle

This button enables the DVD’s Subtitle menu.

REPLACING THE REMOTE BATTERY

Press tab here
and pull battery tray out

Battery

Use a single 3V battery, type CR2025. Insert as shown. Observe the
correct orientation of the battery as marked on the battery tray.

Battery life is approximately six months, depending on how often the
remote is used.

14

CD AUDIO, MP3 AND JPEG PLAYBACK

CD Playback

When you insert an audio CD (label facing away from you), the
standard CD commands (PLAY, NEXT, etc.) will control the unit. Some
CDs recorded in CD-R or CD-RW mode may not play.

MP3, JPEG and MPEG Playback

When a disc containing MP3, JPEG or MPEG les is inserted, a menu
screen appears. Use the arrow buttons to select a le type and press

enter to play it.

USB Playback

Inserting a USB drive into the available connector will cause DVD play­back to stop and open a directory of the USB drive contents.

Maximum USB size is 2GB.

This may take several minutes depending on the amount of data. Use

the arrow buttons to select a le type and press enter to play it.

LISTENING OVER THE CAR SPEAKERS

The system uses a wireless FM Transmitter (FMT) to send audio
through the vehicle’s speakers. To listen over your speakers:

1 Make sure system MUTE is off. Press SPEAKER. “SPEAKER

SOUND ON FM _ _ . _” appears. Select a FM frequency as de­scribed below.

2 Turn on the car radio. Tune to the FM frequency displayed on the

screen, such as “FM 88.1.”

3 If no system audio is heard, try changing the FMT frequency and

re-tuning the radio to the new frequency.

To change the FM Transmitter frequency:

Press SPEAKER. “Speaker Sound on FM _ _ . _” will be displayed.
Now use the LEFT and RIGHT buttons to change the frequency.

Select a frequency, re-tune your radio and check for clear sound.

The system saves the frequency you select, and returns to it each time
the system is turned on. You may want to store the FMT frequency as
a preset of your radio for ease of use.

Note: If there seems to be a strong station on the FM Transmit­ter frequency, and you are hearing a radio station mixed in with
the system audio, change the FM Transmitter frequency. Avoid
frequencies used by local radio stations.

If the words “HEADPHONES ONLY” appear, the internal FMT is
turned off. It can be turned on by pressing the SPEAKER button and
selecting a FM frequency. If the words “SPEAKER SOUND” appear,
an external FM Modulator (FMM) is probably being used. In this case,
the SPEAKER button turns the external FMM on and off. The external
FMM frequencies are FM 87.7, 87.9, 88.1, 88.3, 88.5, 88.7, 88.9. If you
have any questions about your FMM, please contact your dealer.

15

AV7800 Owner’s Manual

USING THE INCLUDED WIRELESS HEADPHONES

The system comes with infrared (IR) wireless fold-at headphones.

These headphones receive a signal from an IR transmitter built into the
unit. Headphones allow rear-seat passengers to listen without using
the vehicle speakers.

To turn the headphones on and off, push the Power ON/OFF button on
the earpiece. The Power LED on the earpiece indicates when head­phone power is on. Power turns off automatically after three minutes of
no audio, in order to preserve battery life.

The headphones have a two-position slide switch labeled “A/B.” When
the switch is in the “A” position, the headphones play audio from the
source designated as “A.” When the switch is in the “B” position, the
headphones play audio from the source designated as “B.”

To adjust the headphone volume, rotate the thumb wheel on the head-
phones.

Adjust headphones

here

A/B Switch

On/Off

REPLACING HEADPHONE BATTERIES

The wireless IR headphones require two (2) “AAA” batteries. To
replace the batteries, slide off the battery compartment door on the left
earpiece and insert batteries, as shown. Make certain that the battery
orientation matches the marks inside the battery compartment.

Batteries

16

Volume

USING THE INTEGRATED GAME SYSTEM

There are integrated video games built into the system. The Rosen
Game Controller is included.

Flashing Light

To play a game:

Set the A/Off/B switch to A or B to
turn the game controller on.

Press SOURCE on the remote or
MODE on the front control panel
until “INTERNAL GAME” appears,
along with the game startup menu.

Battery Indicator: A red light will ash when the buttons are pressed

indicating the batteries are ok.

Set the controller to channel A or B depending on which headrest unit
you will be using.

Use the left and right arrows on the controller to select which game you
want to play from the list.

Press START on the controller, to begin a game.

While playing, use A and/or B as re, jump, or other action buttons,
depending on the game.

To return to the game main menu, press RESET on the controller.

Note: The controller works using infrared “line-of-sight” technolo-

gy. If the controller is held so that there is not a clear line of sight
to the system, intermittent operation or reset will result.

USING EXTERNAL SOURCES

You may use optional external video games, camcorders, and other
portable video units by connecting the unit to the auxiliary RCA input
jacks on the side of the unit.

Aux A/V Input
(Side of the unit)

To use an external game system, a 12VDC to 110VAC power inverter,
available at most electronic retail stores, is often required.

Note: If you want to watch non-widescreen, 4:3 images, press
the DISPLAY button on the remote control until “STANDARD”

is displayed on the screen. This will properly size the image,
instead of stretching the image across the wide screen. In

“STANDARD” mode, you will see black bars on the sides of the
image.

17

AV7800 Owner’s Manual

DVD TYPICAL SETUP AND CONFIGURATION

The following section explains how to customize various features of the
Internal DVD Player, including languages, display, and parental control
features.

Note: Some features may not be available on your system.

Speaker Setup Settings

This allows you to customize the Downmix mode.

To change the settings for the internal DVD player:

1 Press SETUP on the remote.
2 Use the UP and DOWN navigation buttons to highlight a selection.
3 Press the ENTER button to conrm your selection.

Default Settings:

→Downmix = Stereo

General Setup Settings

This allows you to change settings for languages, captions, screen
saver and angle mark.

Note:Not all language settings are supported by all discs.

Default Settings:

→Angle Mark = OFF

→OSD Lang = English

→Captions = OFF

→Screen Saver = OFF

Note: Changing the state of some settings can cause apparent system failure. Do not change any settings other than those described in this section.

Preference Settings

This allows you to customize the audio and disc menu settings, sub­titles and set passwords and parental controls.

Default Settings:

→TV Type = NTSC

→Audio = English

→Subtitle = Off

→Disc Menu = English

→Parental

→Password = 3308

→Default

18

FREQUENTLY ASKED QUESTIONS

HOW DO I RESET MY SYSTEM?

Power the system ON/OFF using the POWER button.

MY SYSTEM IS NOT RESPONDING TO COMMANDS

Periodically, the DVD system may receive conicting commands from

a DVD or remote control. When this happens, the system may not re­spond properly to the remote control, control buttons, or may be locked
up and not respond at all.

Solution: Power system ON/OFF using the POWER button.
Solution: Replace the battery in the remote control.

MY AUDIO HAS STATIC ON THE RADIO

To receive audio over the radio, the radio must be tuned to a broadcast
station which is not in use by a local radio station.
Solution: Set the FM Transmitter to an alternate radio station. Then
tune the radio to the newly selected station. (see pages 7,15)

MY DVD WILL NOT PLAY

Some DVDs will not play properly due to compatibility, dirt, rough
edges, damage to the disc or the system may be beyond its operating
temperature.

Solution: Conrm the DVD is a compatible format. (see page 9)
Solution: Check and clean the DVD as needed.
Solution: Use a pencil or soft wood to smooth the edge of the disk.
Solution: Replace the DVD if scratched, cracked or warped.
Solution: Allow the system temperature to return to normal operating

temperatures. This may take up to an hour after the air temperature in
the vehicle is at a comfortable level.

MY SYSTEM RESETS WHEN I START MY VEHICLE

Voltage levels while starting the vehicle can fall below the minimum
operating levels for the system.

Solution: Ensure your battery is fully charged and in good condition.
Solution: Avoid operating your system without the engine running for

periods longer than 10 minutes.

I CAN NOT GET AUDIO ON THE RADIO

To receive audio over the radio, the system must have SPEAKERS
ENABLE selected, and the radio must be tuned to the proper station.
Solution: Press the SPEAKER button on the remote control to enable
the radio transmission.
Solution: Tune the radio to the proper FM station as directed in the
“Listening Over the Car Speakers” section of this manual. (see page 15)

MY DVD WILL NOT EJECT

Damaged DVDs, incompatible DVDs or improper system installation
will prevent the DVD from ejecting and may lock up the system.
Solution: Power the system ON/OFF using the POWER button, then
quickly press EJECT while the disc is spinning.
Solution: Check the DVD for damage, replace the DVD if scratched,
cracked or warped.

Solution: Conrm the DVD is a compatible format. (see page 9)

I DO NOT HAVE HEADPHONE AUDIO

The headphone audio should be present at all times, unless MUTE is
on, or a DVD setting has been changed in the DVD Settings Menu.
Solution: Press the MUTE button to enable the audio and turn the
MUTE OFF.

Solution: Conrm that the headphones are turned on, and the ON

LED indicator is illuminated. Change batteries if needed.
Solution: Check the DVD settings and restore them to FACTORY
SETTINGS if needed.

MY PICTURE FREEZES

Damaged or incompatible DVDs will cause the system to freeze and
lock up the system.

Solution: Check and clean the DVD as needed.
Solution: Replace the DVD if scratched, cracked or warped.
Solution: Conrm the DVD is a compatible format. (see page 9)
Solution: Allow the system to return to normal operating temperature.
Solution: Reset the system by pressing the POWER button ON/OFF.

19

AV7800 Owner’s Manual

MY RADIO LOSES ITS NORMAL STATIONS

With an external FM Modulator and while the system is set to broad­cast over the radio with SPEAKERS ENABLED, the vehicle’s antenna
is temporarily disabled.
Solution: Press the SPEAKER button on the remote to restore the
vehicle antenna, “Headphones Only” will appear on the screen.

MY PICTURE IS DISTORTED

Excessive cold or hot temperatures will cause the picture on the dis­play to become distorted or lose color or contrast.
Solution: Allow the system temperature to return to normal operating
temperatures. This may take up to an hour after the air temperature in
the vehicle is at a comfortable level.

MY PICTURE IS BLACK

The screen will appear black or dark blue if there is no video signal.
This may happen if the DVD fails to initialize properly or if a source is
selected which is not connected.
Solution: Eject the DVD and inspect it for damage, scratches or
cracks. Clean the DVD and re-insert the disc.

WHY CAN’T I HEAR THE AUDIO OUT OF THE HEADREST OVER
THE CAR SPEAKERS?

Only one headrest at a time can be played through the car’s audio
system. To change this, press the speaker button on the monitor you
want to hear. When you do this you will see “Headphones Only” on the
other screen.

For other questions and capabilities please contact your authorized
dealer.

SERVICE PARTS

Part Number Description

AP1043 IR Remote Control
AP1007 IR Game Controller
AC3640 Dual Channel Fold Flat IR Headphones
AP2027 Quick Start Guide
AP2028 Owner’s Manual

20

PN: AP2028 Rev A

No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic, mechanical, recording or other means without prior written permission.

All rights reserved.