Rosemount Quick Start Guide: Rosemount™ Wireless Pressure Gauge with WirelessHART® Protocol Manuals & Guides

Quick Start Guide

00825-0100-4045 , Rev CA

Feburary 2021

Rosemount™ Wireless Pressure Gauge

with Wireless HART® Protocol

Quick Start Guide Feburary 2021

NOTICE

This guide provides basic guidelines for Rosemount Wireless Pressure Gauges. It does not provide
instructions for configuration, diagnostics, maintenance, service, troubleshooting, or intrinsically safe
(I.S.) installations. Refer to the Rosemount Wireless Pressure Gauge Reference Manual for more
instruction. The manual and this guide are also available electronically.

Shipping considerations

The device is shipped with the battery installed.
Each device contains one “D” size primary lithium-thionyl chloride battery. Primary lithium

batteries are regulated in transportation by the U.S. Department of Transportation, and are also
covered by IATA (International Air Transport Association), ICAO (International Civil Aviation
Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the
responsibility of the shipper to ensure compliance with these or any other local requirements.
Consult current regulations and requirements before shipping.

WARNING

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in accordance with appropriate local,
national, and international standards, codes, and practices.

Ensure device is installed in accordance with intrinsically safe or non-incendive field practices.

Electrical shock could cause death or serious injury.

Care must be taken during transportation of device to prevent electrostatic charge build-up.
Device must be installed to ensure a minimum antenna separation distance of 8 in. (20 cm) from

all persons.

Process leaks could result in death or serious injury.

Handle the transmitter carefully.

Failure to follow these installation guidelines could result in death or serious injury.

Ensure only qualified personnel perform the installation.

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end
users’ equipment. This could be intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and fundamental to protecting your
system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for
all systems used within the facility.

Contents

Required equipment.................................................................................................................... 5

What's in the box?........................................................................................................................ 6

2 Emerson.com/Rosemount

Feburary 2021 Quick Start Guide

Optional: Power/device check...................................................................................................... 8

Optional: Normal range indication option.................................................................................... 9

Installation procedure................................................................................................................ 10

Troubleshooting........................................................................................................................ 14

Product Certifications ................................................................................................................16

Declaration of conformity.......................................................................................................... 21

China RoHS................................................................................................................................ 24

Quick Start Guide 3

Quick Start Guide Feburary 2021

4 Emerson.com/Rosemount

AMS

Feburary 2021 Quick Start Guide

1 Required equipment

Anti-seize paste or PTFE tape (for
NPT threaded connection)

Standard tools, e.g. screwdriver,

wrench, pliers

AMS Wireless Configurator
version 12.0 or later, or Field
Communicator

Quick Start Guide 5

Quick Start Guide Feburary 2021

2 What's in the box?

Wireless Pressure Gauge Quick Start Guide

The following options are also available and will ship with the Rosemount
Wireless Pressure Gauge if ordered.

Rosemount 306 Integral Manifold (Model
code S5)

6 Emerson.com/Rosemount

B4 Bracket (Model code B4)

Feburary 2021 Quick Start Guide

Rosemount 1199 Seal (Model code S1)

Product Certification (Model Codes

Normal Range Indication (Model code LK)

below)
Q4: Calibration Cert
QG: Calibration Cert and GOST

Verification Cert
QP: Calibration Cert and Tamper Evident

Seal
Q8: Material Traceability cert per EN

102043.1
Q15: Cert of Compliance to NACE

MR0175/ISO 15156 for wetted materials
Q25: Cert of Compliance to NACE

MR00103 for wetted materials

Quick Start Guide 7

Quick Start Guide Feburary 2021

3 Optional: Power/device check

The device is designed to be installation-ready. To check device battery prior
to installation, perform the following:

Procedure

1. Perform Turn on device.

2. Slide the ON/OFF switch to the OFF position until ready for use.

8 Emerson.com/Rosemount

Feburary 2021 Quick Start Guide

4 Optional: Normal range indication option

Procedure

1. Modify each of the stickers to desired size prior to proceeding to step

Step 2.

The stickers are intended to be installed on the dial only and should
not be applied on the inside or outside of the housing cover.

2. Remove housing cover.

3. Slide ON/OFF switch to the OFF position and wait for LED to stop
flashing.

4. Gently move the needle in the clockwise direction until it is pointing
at the Red X.

Note

Use caution as the electronics assembly is connected to the needle.

5. Remove any debris on the dial, so it does not become trapped under
the sticker.

6. Peel back the white paper backing of the sticker.

7. Slowly lower the sticker onto the surface of the dial in the desired
location and rub it in place firmly. Repeat steps 6 and 7 until desired
indication locations are set.

• Stickers should be applied in an environment where the ambient

temperature is above 50 °F (10 °C).

• Moving the sticker after initial contact is not recommended as

this decreases the amount of adhesive on the back of the sticker.

8. Slide ON/OFF switch to the ON position.

9. Replace housing cover.

Quick Start Guide 9