Quick Start Guide
00825-0600-4026, Rev BA
December 2016
Rosemount™ 5400 Level Transmitter
Mounting Instructions for Parabolic Antenna
Quick Start Guide
December 2016
1.0 About this guide
This Quick Start Guide provides mechanical installation instructions for the
Rosemount 5402 Level Transmitter with parabolic antenna.
For information about electrical installation and configuration, refer to the
Rosemount 5400 Quick Start Guide
Failure to follow safe installation and service guidelines could result in death or serious injury.
Make sure the transmitter is installed by qualified personnel and in accordance with applicable code of
practice.
Use the equipment only as specified in this Quick Start Guide and the Reference Manual. Failure to do so
may impair the protection provided by the equipment.
Any substitution of non-author ized parts or repair, other than exchanging the complete transmitter head or
antenna assembly, may jeopardize safety and is prohibited.
Explosions could result in death or serious injury.
Verify that the operating environment of the transmitter is consistent with the appropriate hazardous
locations specifications.
To prevent ignition of flammable or combustible atmospheres, disconnect power before servicing.
Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in the
loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.
To avoid process leaks, only use O-rings designed to seal with the corresponding flange adapter.
Do not remove the transmitter while in operation.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads can cause electrical
shock.
Make sure the main power to the Rosemount 5400 Level Transmitter is off and the lines to any other
external power source are disconnec ted or not powered while wiring the transmitter.
Ground device on non-metallic tanks (e.g. fiberglass tanks) to prevent electrostatic charge build-up.
.
Contents
Parabolic antenna overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Mount the flanged version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Mount the threaded version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Mount the welded version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Adjust the inclination of the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 15
Connect the air purging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 19
2
December 2016
page 4
page 5
page 9
2.0 Parabolic antenna overview
Flanged version
Threaded version
Quick Start Guide
Welded version
3
Quick Start Guide
Gasket
3.0 Mount the flanged version
Step 1: Mount the device on tank
Tighten the bolts and nuts with sufficient torque for the flange and gasket
choice.
December 2016
Step 2: Adjust the inclination of the antenna (see page 15)
Step 3: Connect the air purging (see page 19)
4
December 2016
2x
1x
E
1x
F
1x
G
1x
D
1x
C
1x
B
1x
A
4.0 Mount the threaded version
Figure 1. Components
Quick Start Guide
A.
Antenna
B.
Purge plug kit (optional with order)
P/N 05400-1200-0001
Threaded sleeve
C.
M20 adapter
D.
E.
Lock nut G 3½" (optional with order)
P/N 05400-1200-0002
Antenna adapter with ball joint
F.
G.
O-ring
5
Quick Start Guide
E
F
G
Ø 3.98 ± 0.02 in.
(Ø 101 ± 0.6 mm)
OR
G 3½"
Max. 1.18 in. (30 mm)
> 0.59 in. (15 mm)
Step 1: Remove the lock nut (if applicable)
Step 2: Mount the O-ring
Step 3: Mount the antenna adapter on flange/manhole
Ensure the antenna adapter fits tightly to the flange/manhole cover.
December 2016
cover
6
Loading...