Rosemount Quick Start Guide: Rosemount 2051HT Hygienic Pressure Transmitter with FOUNDATION™ Fieldbus Manuals & Guides

Quick Start Guide

00825-0200-4591, Rev BA

November 2019

Rosemount™ 2051HT Hygienic Pressure
Transmitter

with FOUNDATION™ Fieldbus Protocol

Quick Start Guide November 2019

Contents

About this guide...........................................................................................................................3

System readiness......................................................................................................................... 6

Transmitter installation................................................................................................................ 7

Product certifications................................................................................................................. 23

2 Rosemount 2051HT

November 2019 Quick Start Guide

1 About this guide

1.1 Safety messages

This guide provides basic guidelines for the Rosemount 2051HT Transmitter.
It does not provide instructions for configuration, diagnostics, maintenance,
service, troubleshooting, Explosion-proof, Flameproof, or intrinsically safe
(I.S.) installations.

CAUTION

The products described in this document are NOT designed for nuclear­qualified applications. Using non-nuclear qualified products in applications
that require nuclear-qualified hardware or products may cause inaccurate
readings. For information on Rosemount nuclear-qualified products, contact
your local Emerson Sales Representative.

Quick Start Guide 3

Quick Start Guide November 2019

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in
accordance with the appropriate local, national, and international standards,
codes, and practices. Review the approvals section of this manual for any
restrictions associated with a safe

• Before connecting a Field Communicator in an explosive atmosphere,

ensure the instruments in the loop are installed in accordance with
intrinsically safe or non-incendive field wiring practices.

• In an explosion-proof/flameproof installation, do not remove the

transmitter covers when power is applied to the unit.

Process leaks may cause harm or result in death.

• Install and tighten process connectors before applying pressure.

• Do not attempt to loosen or remove flange bolts while the transmitter is

in service.

Electrical shock can result in death or serious injury.

• Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

• Before connecting a handheld communicator in an explosive

atmosphere, ensure the instruments in the loop are installed in
accordance with intrinsically safe or non-incendive field wiring practices.

• In an Explosion-Proof/Flameproof installation, do not remove the

transmitter covers when power is applied to the unit.

Process leaks may cause harm or result in death.

• Install and tighten process connectors before applying pressure.

Physical access

• Unauthorized personnel may potentially cause significant damage to

and/or misconfiguration of end users’ equipment. This could be
intentional or unintentional and needs to be protected against.

• Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by
unauthorized personnel to protect end users’ assets. This is true for all
systems used within the facility.

4 Rosemount 2051HT

November 2019 Quick Start Guide

WARNING

Replacement equipment or spare parts not approved by Emerson for use
as spare parts could reduce the pressure retaining capabilities of the
transmitter and may render the instrument dangerous.

• Use only bolts supplied or sold by Emerson as spare parts.

Improper assembly of manifolds to traditional flange can damage sensor
module.

For safe assembly of manifold to traditional flange, bolts must break back
plane of flange web (i.e., bolt hole) but must not contact sensor module
housing.

Physical access

• Unauthorized personnel may potentially cause significant damage to

and/or misconfiguration of end users’ equipment. This could be
intentional or unintentional and needs to be protected against.

• Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by
unauthorized personnel to protect end users’ assets. This is true for all
systems used within the facility.

Quick Start Guide 5

Quick Start Guide November 2019

2 System readiness

2.1 Confirm correct device driver

• Verify the latest device driver (DD/DTM™) is loaded on your systems to

ensure proper communications.

• Download the latest device driver at Emerson.com or

FieldCommGroup.org.

2.1.1 Device revisions and drivers

Table 2-1 provides the information necessary to ensure you have the correct

device driver and documentation for your device.

Table 2-1: FOUNDATION Fieldbus Device Revisions and Files

Device
Revision

(1)

2 All DD4: DD Rev 1 FieldCommGrou

(1) FOUNDATION Fieldbus device revision can be read using a FOUNDATION Fieldbus capable

(2) Device driver file names use device and DD revision. To access functionality, the correct

Host Device driver

All DD5: DD Rev 1 FieldCommGrou

Emerson AMS Device

Emerson AMS Device

Emerson Field

configuration tool.

device driver must be installed on your control and asset management hosts, and on your
configuration tools.

(2)

(DD)

Manager V 10.5
or higher: DD
Rev 2

Manager V 8 to

10.5: DD Rev 1

Communicator:
DD Rev 2

Obtain at Device driver

(DTM)

Emerson.com Rosemount

p.org

p.org

Emerson.com

Emerson.com

Easy upgrade
utility

Manual
Document
Number

2051 Pressure
Transmitter

Reference
Manual or

newer

6 Rosemount 2051HT

Start

Mount the

transmitter

Commissioning

tag

Done

Zero trim the

transmitter

Configuration

Grounding, wiring,

and power up

Set switches and

software write lock

Locate device

November 2019 Quick Start Guide

3 Transmitter installation

Figure 3-1: Installation Flowchart

3.1 Mount the transmitter

Adjust the transmitter to desired orientation before mounting. Transmitter
must not be securely mounted or clamped in place when changing
transmitter orientation.

3.1.1 Conduit entry orientation

When installing a Rosemount 2051HT, it is recommended installing so a
conduit entry faces downward toward the ground to maximize drainability
when cleaning.

3.1.2 Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to
provide a water/dust tight conduit seal and meets requirements of NEMA
Type 4X, IP66, IP68, and IP69K. Consult factory if other Ingress Protection
ratings are required.

For M20 threads, install conduit plugs to full thread engagement or until
mechanical resistance is met.

Note

IP69K rating only available on units with a SST housing and option code V9 in
the model string.

Note

For aluminum housings ordered with M20 conduit entries, transmitters
shipped will have NPT threads machined into the housing and a NPT to M20

Quick Start Guide 7

thread adapter will be provided. Considerations for environmental sealing
listed above should be taken into account when installing the thread
adapter.

®

A

Quick Start Guide November 2019

3.1.3 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage
transmitter is located on the neck of the transmitter via a protected gage
vent (See Figure 3-2).

Keep the vent path free from obstructions including but not limited to paint,
dust, and viscous fluids by mounting the transmitter so the process can drain
away. Recommended installations have a conduit entry facing the ground so
the gage vent port is pointing parallel to the ground.

Figure 3-2: In-line Protected Gage Vent Low Side Pressure Port

Aluminum Polished 316 SST

A. Low side pressure port (atmospheric reference)

3.1.4 Clamping

When installing clamp, follow recommended torque values provided by
gasket manufacturer.

Note

To maintain performance, torquing a 1.5. Tri-Clamp® beyond 50 in-lb is not
recommended on pressure ranges below 20 psi.

3.2

8 Rosemount 2051HT

Commissioning (paper) tag

To identify which device is at a particular location use the removable tag
provided with the transmitter. Ensure the physical device tag (PD tag field) is
properly entered in both places on the removable commissioning tag and
tear off the bottom portion for each transmitter.

November 2019 Quick Start Guide

Note

The device description loaded in the host system must be at the same
revision as this device.

Figure 3-3: Commissioning Tag

A. Device revision

Note

The device description loaded in the host system must be at the same
revision as this device. The device description can be downloaded from the
host system website or Emerson.com/Rosemount by selecting Download
Device Drivers under Product Quick Links. You can also visit Fieldbus.org and
select End User Resources.

3.3

Quick Start Guide 9

Setting security switch

Prerequisites

Set Simulate and Security switch configuration before installation as shown
in Figure 3-4.

• The simulate switch enables or disables simulated alerts and simulated

AI Block status and values. The default simulate switch position is
enabled.

• The Security switch allows (unlocked symbol) or prevents (locked

symbol) any configuration of the transmitter.

• Default security is off (unlocked symbol).

• The security switch can be enabled or disabled in software.

Use the following procedures to change the switch configuration:

A

B

Quick Start Guide November 2019

Procedure

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side. Do not
remove the instrument cover in explosive atmospheres when the
circuit is live.

3. Slide the security and simulate switches into the preferred position.

4. Reattach transmitter housing cover; it is recommended the cover be
tightened until there is no gap between the cover and housing to
comply with explosion proof requirements.

3.4 Setting simulate switch

The simulate switch is located on the electronics. It is used in conjunction
with the transmitter simulate software to simulate process variables and/or
alerts and alarms. To simulate variables and/or alerts and alarms, the
simulate switch must be moved to the enable position and the software
enabled through the host. To disable simulation, the switch must be in the
disable position or the software simulate parameter must be disabled
through the host.

Figure 3-4: Transmitter Electronics Board

Aluminum Polished 316 SST

A. Simulate switch
B. Security switch

10 Rosemount 2051HT