Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
Appendix A Reference Data
3051SFA Ordering Information . . . . . . . . . . . . . . . . . . . . . page A-1
3051SFA Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .page A-10
3051CFA Ordering Information . . . . . . . . . . . . . . . . . . . . . page A-21
3051CFA Performance Specifications . . . . . . . . . . . . . . .page A-27
2051CFA Ordering Information . . . . . . . . . . . . . . . . . . . . . page A-33
2051CFA Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .page A-38
3095MFA Ordering Information . . . . . . . . . . . . . . . . . . . . .page A-43
3095MFA Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-48
485 Annubar Primary Element Ordering Information . . .page A-57
485 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-62
585 Annubar Primary Element Ordering Information . . .page A-67
3051SF Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . page A-76
3051CF Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . page A-82
2051CF Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . page A-88
3095MFA Dimensional Drawings . . . . . . . . . . . . . . . . . . . . page A-91
485 Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . page A-97
585 Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . page A-103
3051SFA ORDERING
INFORMATION
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Measurement
Type
Model Product Description
3051SFA Annubar Flowmeter • •
Measurement Type
Standard Standard
1 MultiVariable (Fully Compensated Mass & Energy Flow) – Differential & Static Pressures w/
Temperature
2 MultiVariable (Compensated Flow) – Differential & Static Pressures — • ★
3 MultiVariable (Compensated Flow) – Differential Pressure & Temperature — • ★
4 MultiVariable (Compensated Flow) – Differential Pressure — • ★
5 MultiVariable (Direct Measurement) – Differential & Static Pressures with Temperature — • ★
6 MultiVariable (Direct Measurement) – Differential & Static Pressures — • ★
7 MultiVariable (Direct Measurement) – Differential Pressure & Temperature — • ★
D Differential Pressure • — ★
D 1-7
— • ★
• = Available
— = Unavailable
www.rosemount.com
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Fluid Type
Standard Standard
L Liquid • • ★
G Gas • • ★
S Steam • • ★
Line Size D 1-7
Standard Standard
020 2-in. (50 mm) • • ★
025 21/2-in. (63.5 mm) • • ★
030 3-in. (80 mm) • • ★
035 31/2-in. (89 mm) • • ★
040 4-in. (100 mm) • • ★
050 5-in. (125 mm) • • ★
060 6-in. (150 mm) • • ★
070 7-in. (175 mm) • • ★
080 8-in. (200 mm) • • ★
100 10-in. (250 mm) • • ★
120 12-in. (300 mm) • • ★
Expanded
140 14-in. (350 mm) • •
160 16-in. (400 mm) • •
180 18-in. (450 mm) • •
200 20-in. (500 mm) • •
240 24-in. (600 mm) • •
300 30-in. (750 mm) • •
360 36-in. (900 mm) • •
420 42-in. (1066 mm) • •
480 48-in. (1210 mm) • •
600 60-in. (1520 mm) • •
720 72-in. (1820 mm) • •
780 78-in (1950 mm) • •
840 84-in. (2100 mm) • •
900 90-in. (2250 mm) • •
960 96-in (2400 mm) • •
Pipe I.D. Range
Standard Standard
C Range C from the Pipe I.D. table • • ★
D Range D from the Pipe I.D. table • • ★
Expanded
A Range A from the Pipe I.D. table • •
B Range B from the Pipe I.D. table • •
E Range E from the Pipe I.D. table • •
Z Non-standard Pipe I.D. Range or Line Sizes greater than 12-in. (300 mm) • •
Pipe Material / Mounting Assembly Material
Standard Standard
C Carbon steel (A105) • • ★
S 316 Stainless Steel • • ★
(1)
0
No Mounting (Customer Supplied) • • ★
March 2012
A-2
Reference Manual
00809-0100-4809, Rev CB
March 2012
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Expanded
G Chrome-Moly Grade F-11 • •
N Chrome-Moly Grade F-22 • •
J Chrome-Moly Grade F-91 • •
Piping Orientation
Standard Standard
H Horizontal Piping • • ★
D Vertical Piping with Downwards Flow • • ★
U Vertical Piping with Upwards Flow • • ★
Annubar Type D 1-7
Standard Standard
P Pak-Lok • • ★
F Flanged with opposite side support • • ★
Expanded
L Flange-Lok • •
G Gear-Drive Flo-Tap • •
M Manual Flo-Tap • •
Sensor Material
Standard Standard
S 316 Stainless Steel • • ★
Expanded
H Alloy C-276 • •
Sensor Size
Standard Standard
1 Sensor size 1 — Line sizes 2-in. (50 mm) to 8-in. (200 mm) • • ★
2 Sensor size 2 — Line sizes 6-in. (150 mm) to 96-in. (2400 mm) • • ★
3 Sensor size 3 — Line sizes greater than 12-in. (300 mm) • • ★
Mounting Type
Standard Standard
T1 Compression or Threaded Connection • • ★
A1 150# RF ANSI • • ★
A3 300# RF ANSI • • ★
A6 600# RF ANSI • • ★
D1 DN PN16 Flange • • ★
D3 DN PN40 Flange • • ★
D6 DN PN100 Flange • • ★
Expanded
(2)
A9
(2)
AF
(2)
AT
R1 150# RTJ Flange • •
R3 300# RTJ Flange • •
R6 600# RTJ Flange • •
(2)
R9
(2)
RF
(2)
RT
Opposite Side Support or Packing Gland
Standard Standard
0 No opposite side support or packing gland (Required for Pak-Lok and Flange-Lok models) • • ★
C NPT Threaded Opposite Support Assembly – Extended Tip • • ★
D Welded Opposite Support Assembly – Extended Tip • • ★
900# RF ANSI • •
1500# RF ANSI • •
2500 # RF ANSI • •
900# RTJ Flange • •
1500# RTJ Flange • •
2500# RTJ Flange • •
Opposite Side Support – Required for Flanged Models
Annubar Flowmeter Series
A-3
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Expanded
Packing Gland – Required for Flo-Tap Models
Packing Gland Material Rod Material Packing Material
J Stainless Steel Packing Gland / Cage Nipple Carbon Steel PTFE • •
K Stainless Steel Packing Gland / Cage Nipple Stainless Steel PTFE • •
L Stainless Steel Packing Gland / Cage Nipple Carbon Steel Graphite • •
N Stainless Steel Packing Gland / Cage Nipple Stainless Steel Graphite • •
R Alloy C-276 Packing Gland / Cage Nipple Stainless Steel Graphite • •
Isolation Valve for Flo-Tap Models D 1-7
Standard Standard
(1)
0
Expanded
1 Gate Valve, Carbon Steel • •
2 Gate Valve, Stainless Steel • •
5 Ball Valve, Carbon Steel • •
6 Ball Valve, Stainless Steel • •
Temperature Measurement
Standard Standard
(3)
T
(4)
0
Expanded
(3)
R
Transmitter Connection Platform
Standard Standard
3 Direct-mount, Integral 3-valve Manifold– not available with Flanged model greater than class
5 Direct -mount, 5-valve Manifold – not available with Flanged model greater than class 600 • • ★
7 Remote-mount NPT Connections (1/2-in. FNPT) • • ★
Expanded
6 Direct-mount, High Temperature 5-valve Manifold – not available with Flanged model greater
8 Remote-mount SW Connections (1/2-in.) • •
Differential Pressure Range
Standard Standard
1 0 to 25 in H2O (0 to 62,3 mbar) • • ★
2 0 to 250 in H2O (0 to 623 mbar) • • ★
3 0 to 1000 in H2O (0 to 2,5 bar) • • ★
Static Pressure Range
Standard Standard
(5)
A
D Absolute 0.5 to 800 psia (0,033 to 55,2 bar) — • ★
(6)
E
J Gage -14.2 to 800 psig (-0,979 to 55,2 bar) — • ★
(6)
K
Transmitter Output
Standard Standard
A 4–20 mA with digital signal based on HART protocol • • ★
F FOUNDATION fieldbus protocol (requires PlantWeb housing) • — ★
(7)
X
Not Applicable or Customer Supplied • • ★
Integral RTD – not available with Flanged model greater than class 600# • • ★
No Temperature Sensor • • ★
Remote Thermowell and RTD • •
• • ★
600
• •
than class 600
None • • ★
Absolute 0.5 to 3626 psia (0,033 to 250 bar) — • ★
Gage -14.2 to 3626 psig (-0,979 to 250 bar) — • ★
Wireless (Requires wireless options and Wireless Plantweb housing) • — ★
March 2012
A-4
Reference Manual
00809-0100-4809, Rev CB
March 2012
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Transmitter Housing Style Material
Standard Standard
00 None (Customer-supplied electrical connection) • — ★
1A PlantWeb Housing Aluminum
1B PlantWeb Housing Aluminum M20 x 1.5 • • ★
1J PlantWeb Housing SST
1K PlantWeb Housing SST M20 x 1.5 • • ★
2A Junction Box Housing Aluminum
2B Junction Box Housing Aluminum M20 x 1.5 • — ★
2E Junction Box housing with output for remote display and
2F Junction Box housing with output for remote display and
2J Junction Box Housing SST
2M Junction Box housing with output for remote display and
5A Wireless PlantWeb housing Aluminum
5J Wireless PlantWeb housing SST
(7)(8)
7J
Expanded
1C PlantWeb Housing Aluminum G1/2 • •
1L PlantWeb Housing SST G1/2 • •
2C Junction Box Housing Aluminum G1/2 • —
2G Junction Box housing with output for remote display and
Transmitter Performance Class D 1-7
Standard Standard
3051S MultiVariable SuperModule, Measurement Types 1, 2, 5, and 6
3 Ultra for Flow: 0.8% flow rate accuracy, 14:1 flow turndown, 10-year stability. limited 12-year
5 Classic MV: 0.85% flow rate accuracy, 8:1 flow turndown, 5-yr. stability — • ★
3051S Single Variable SuperModule, Measurement Types 3, 4, 7, and D
1 Ultra: up to 0.9% flow rate accuracy, 8:1 flow turndown, 10-year stability, limited 12-year
2 Classic: up to 1.1% flow rate accuracy, 8:1 flow turndown, 5-year stability • — ★
(9)
3
interface
interface
interface
Quick Connect (A size Mini, 4-pin male termination) • — ★
interface
warranty
warranty
Ultra for Flow: 0.8% flow rate accuracy, 14:1 flow turndown, 10-year stability,. limited 12-year
warranty
Annubar Flowmeter Series
Conduit Entry
Size
1
/2-14 NPT • • ★
1
/2-14 NPT • • ★
1
/2-14 NPT • — ★
Aluminum
Aluminum M20 x 1.5 • — ★
SST
Aluminum G1/2 • —
1
/2-14 NPT • — ★
1
/2-14 NPT • — ★
1
/2-14 NPT • — ★
1
/2-14 NPT • — ★
1
/2-14 NPT • — ★
• • ★
• — ★
• • ★
Wireless Options (Requires option code X and wireless PlantWeb housing)
Update Rate, Operating Frequency and Protocol
Standard Standard
WA User Configurable Update Rate • — ★
Operating Frequency and Protocol
Standard
3 2.4 GHz DSSS, WirelessHART • — ★
Omnidirectional Wireless Antenna
Standard
(10)
WK
SmartPower
Standard
(11)
1
Long Range, Integral Antenna • — ★
™
Power Module Adapter, Intrinsically Safe (Power Module separate) • — ★
A-5
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
March 2012
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Other Options (Include with selected model number)
Pressure Testing
Expanded
(12)
P1
(12)
PX
Special Cleaning
Expanded
P2 Cleaning for Special Services • •
PA Cleaning per ASTM G93 level D (section 11.4) • •
Material Testing
Expanded
V1 Dye Penetrant Exam • •
Material Examination
Expanded
V2 Radiographic Examination • •
Flow Calibration
Expanded
W1 Flow Calibration (Average K) • •
Special Inspection
Standard Standard
QC1 Visual and Dimensional Inspection with Certificate • • ★
QC7 Inspection and Performance Certificate • • ★
Surface Finish
Standard Standard
RL Surface finish for Low Pipe Reynolds Number in Gas and Steam • • ★
RH Surface finish for High Pipe Reynolds Number in Liquid • • ★
Material Traceability Certification
Standard Standard
(13)
Q8
Code Conformance
Expanded
(14)
J2
(14)
J3
Material Conformance
Expanded
(15)
J5
Country Certification
Standard Standard
J6 European Pressure Directive (PED) • • ★
Expanded
J1 Canadian Registration • •
Installed in Flanged Pipe Spool Section
Expanded
H3 150# Flanged Connection with Rosemount Standard Length and Schedule • •
H4 300# Flanged Connection with Rosemount Standard Length and Schedule • •
H5 600# Flanged Connection with Rosemount Standard Length and Schedule • •
Instrument Connections for Remote Mount Option
Standard Standard
G2 Needle Valves, Stainless Steel • • ★
G6 OS&Y Gate Valve, Stainless Steel • • ★
Hydrostatic Testing with Certificate • •
Extended Hydrostatic Testing • •
D 1-7
Material Traceability Certificate per EN 10204:2004 3.1 • • ★
ANSI B31.1 • •
ANSI B31.3 • •
NACE MR-0175 / ISO 15156 • •
A-6
Reference Manual
00809-0100-4809, Rev CB
March 2012
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Expanded
G1 Needle Valves, Carbon Steel • •
G3 Needle Valves, Alloy C-276 • •
G5 OS&Y Gate Valve, Carbon Steel • •
G7 OS&Y Gate Valve, Alloy C-276 • •
Special Shipment
Standard Standard
Y1 Mounting Hardware Shipped Separately • • ★
Special Dimensions
Expanded
VM Variable Mounting • •
VT Variable Tip • •
VS Variable length Spool Section • •
Transmitter Calibration Certification
Standard Standard
Q4 Calibration Certificate for Transmitter • • ★
Quality Certification For Safety
Standard Standard
QS Certificate of FMEDA data • — ★
(16)(17)(19)
QT
Product Certifications
Standard Standard
E1 ATEX Flameproof • • ★
I1 ATEX Intrinsic Safety • • ★
IA ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus protocol only • — ★
N1 ATEX Type n • • ★
ND ATEX Dust • • ★
K1 ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E1, I1, N1, and ND) • • ★
E4 TIIS Flameproof • • ★
E5 FM Explosion-proof, Dust Ignition-proof • • ★
I5 FM Intrinsically Safe, Division 2 • • ★
K5 FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5 and I5) • • ★
(16)
E6
I6 CSA Intrinsically Safe • • ★
(16)
K6
E7 IECEx Flameproof, Dust Ignition-proof • • ★
I7 IECEx Intrinsic Safety • • ★
K7 IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, Type n (combination of E7, I7, and N7) • • ★
E3 China Flameproof • • ★
I3 China Intrinsic Safety • • ★
(16)
KA
(16)
KB
KC FM and ATEX Explosion-proof, Intrinsically Safe, Division 2 (combination of E5, E1, I5, and I1) • • ★
(16)
KD
Alternate Transmitter Material of Construction
Standard Standard
L1 Inert Sensor Fill Fluid
L2 Graphite-Filled (PTFE) O-ring • • ★
LA Inert Sensor Fill Fluid and Graphite-Filled (PTFE) O-ring • • ★
Safety certified to IEC 61508 with certificate of FMEDA data • — ★
CSA Explosion-proof, Dust Ignition-proof, Division 2 • • ★
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E6 and
I6)
ATEX and CSA Explosion-proof, Intrinsically Safe, Division 2 (combi nation of E1, I1, E6, and I6) • • ★
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2
(combination of E5, E6, I5, and I6)
FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of E5, I5, E6, I6, E1, and
I1)
Note: Silicone fill fluid is standard.
Annubar Flowmeter Series
D 1-7
• • ★
• • ★
• • ★
• • ★
A-7
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
Table A-1. Rosemount 3051SFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Digital Display
Standard Standard
M5 PlantWeb LCD display (Requires PlantWeb housing) • • ★
(18)(19)
M7
(18)(19)(20)
M8
(18)(19)(20)
M9
Transient Protection
Standard Standard
(21)
T1
Manifold for Remote Mount Option
Standard Standard
F2 3-Valve Manifold, Stainless Steel • • ★
F6 5-Valve Manifold, Stainless Steel • • ★
Expanded
F1 3-Valve Manifold, Carbon Steel • •
F3 3-Valve Manifold, Alloy C-276 • •
F5 5-Valve Manifold, Carbon Steel • •
F7 5-Valve Manifold, Alloy C-276 • •
PlantWeb Control Functionality
Standard Standard
A01 FOUNDATION fieldbus Advanced Control Function Block Suite • — ★
PlantWeb Diagnostic Functionality
Standard Standard
D01 FOUNDATION fieldbus Diagnostics Suite • — ★
(22)
DA2
PlantWeb Enhanced Measurement Functionality
Standard Standard
(23)
H01
Cold Temperature
Standard Standard
BRR -60 °F (-51 °C) Cold Temperature Start-up • • ★
Alarm Limit
Standard Standard
C4 NAMUR Alarm and Saturation Levels, High Alarm • • ★
C5 NAMUR Alarm and Saturation Levels, Low Alarm • • ★
C6 Custom Alarm and Saturation Levels, High Alarm • • ★
C7 Custom Alarm and Saturation Levels, Low Alarm • • ★
C8 Low Alarm (Standard Rosemount Alarm and Saturation Levels) • • ★
Hardware Adjustments and Ground Screw
Standard Standard
D1 Hardware Adjustments (zero, span, alarm, security) • — ★
D4 External Ground Screw Assembly • • ★
DA Hardware Adjustments (zero, span, alarm, security) and External Ground Screw Assembly • — ★
Conduit Electrical Connector
Standard Standard
(25)
GE
(25)
GM
Typical Model Number: 3051SFA D L 060 D C H P S 2 T1 0 0 0 3 2A A 1A 3
(1) Provide the “A” dimension for Flanged (page A-78), Flange-Lok (page A-77), and Threaded Flo-Tap (page A-81) models. Provide the “B” dimension for
Flange Flo-Tap models (page A-80).
(2) Available in remote mount applications only.
(3) Temperature Measurement Option code T or R is required for Measurement Type codes 1, 3, 5, and 7.
(4) Required for Measurement Type codes 2, 4, 6, and D.
(5) Required for Measurement Type codes 3, 4, 7, and D.
(17)
Remote mount LCD display and interface, no cable; PlantWeb housing, SST bracket • • ★
Remote mount LCD display and interface, 50 ft. (15 m) cable; PlantWeb housing, SST bracket • • ★
Remote mount LCD display and interface, 100 ft. (31 m) cable; PlantWeb housing, SST bracket • • ★
Transient terminal block • • ★
D 1-7
Advanced HART Diagnostic Suite • — ★
FOUNDATION fieldbus Fully Compensated Mass Flow Block • — ★
(18)(24)
M12, 4-pin, Male Connector (eurofast®) • • ★
A size Mini, 4-pin, Male Connector (minifast®) • • ★
March 2012
A-8
Reference Manual
00809-0100-4809, Rev CB
March 2012
(6) For Measurement Type 1, 2, 5, and 6 with DP range 1, absolute limits are 0.5 to 2000 psi (0,03 to 137,9 bar) and gage limits are
-14.2 to 2000 psig (-0,98 to 137,9 bar).
(7) Available approvals are FM Int rinsically Safe, Division 2 (opt ion code I5), CSA Intrinsicall y Safe (option code I6), ATEX Intrinsic Safety (o ption code I1), and
IECEx Intrinsic Safety (option code I7).
(8) Available with output code A only.
(9) This option is only available with differential pressure ranges 2 and 3, and silicone fill fluid.
(10) Long-Life Power Module must be shipped separately, order Part #00753-9220-0001.
(11) Long-life Power Module must be shipped separately, order Part No. 00753-9220-0001.
(12) Applies to assembled flowmeter only, mounting not tested.
(13) Instrument Connections for Remote Mount Options and Isolation Valves for Flo-tap Models are not included in the Material Traceability Certification.
(14) Not available with Transmitter Connection Platform 6.
(15) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO 15156 for sour oil field production environment s. Environmental
limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(16) Not available with M20 or G ½ conduit entry size.
(17) Not available with housing code 7J.
(18) Not available with output code X.
(19) Not available with output code F, option code DA2, or option code QT.
(20) Cable supplied is Belden 3084A, rated for ambient temperatures up to 167 °F (75 °C).
(21) Not available with Housing code 00, 5A, or 7J. External ground screw assembly (option code D4) is included with t he T1 option. The T1 option is not needed
with FISCO Product Certifications, transient protection is included with the FISCO Product Certification code IA.
(22) Includes Hardware Adjustments (option code D1) as standard.
(23) Requires Rosemount Engineering Assistant version 5.5.1 to configure.
(24) Not available with Output Protocol code F.
(25) Not available with Housing code 00, 5A, or 7J. Available with Intrinsically Safe approvals only. For FM Intrinsically Safe, Division 2 (option code I5) or FM
FISCO Intrinsically Safe (option code IE), install in accordance with Rosemount drawing 03151-1009 to maintain outdoor rating (NEMA 4X and IP66).
Annubar Flowmeter Series
A-9
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
March 2012
3051SFA SPECIFICATIONS
3051SFA
PERFORMANCE
SPECIFICATIONS
Performance assumptions include: measured pipe I.D, transmitter is trimmed for optimum flow accuracy, and
performance is dependent on application parameters.
Table A-2. MultiVariable Flow Performance - Flow Refe rence Accuracy (Measurement Type 1)
3051SFA Annubar Flowmeter
Classic MV (8:1 flow turndown) Ultra for Flow (14:1 flow turndown)
Ranges 2-3 1.15% of Flow Rate ±0.80% of Flow Rate
(1) Measurement Types 2 - 4 assume that the unmeasured variables are constant. Additional uncertainty will depend on the variation in the unmeasured
variables.
Table A-3. Flow Performance - Flow Reference Accuracy (Measurement Type D)
3051SFA Annubar Flowmeter
Classic (8:1 flow turndown) Ultra (8:1 flow turndown) Ultra for Flow (14:1 flow turndown)
Ranges 2-3 ±1.4% of Flow Rate ±0.95% of Flow Rate ±0.80% of Flow Rate
(1) For Measurement Types 5 - 7, refer to the Reference Accuracy specification for the 3051SMV with Measur ement Type P.
(2) These flow measurement accuracies assume a constant density, viscosity, and expansibility factor.
(1)(2)
(1)
3051SFA DYNAMIC
PERFORMANCE
Total Time Response at 75 °F (24 °C), includes dead time
3051SF_D 3051SF_1, 2, 5, or 6 3051SF_3, 4, or 7
DP Ranges 2-5: 100 ms
Range 1: 255 ms
Range 0: 700 ms
(1) For F
OUNDATION fieldbus (output code F), add 52 ms to stated values (not including
segment macro-cycle).
For option code DA2, add 45 ms (nominal) to stated values.
DP Range 1: 310 ms
DP Range 2: 170 ms
DP Range 3: 155 ms
AP & GP: 240 ms
DP Ranges 2-5: 145 ms
DP Range 1: 300 ms
DP Range 0: 745 ms
(1)
A-10
Dead Time
3051SF_D 3051SF_1-7
45 ms (nominal) DP: 100 ms
(1) For option code DA2, dead time is 90 milliseconds (nominal).
Update Rate
3051SF_D 3051SF_1-7
22 updates per sec. DP: 22 updates per sec.
(1) Does not apply to Wireless (output code X). See “Wireless Self-Organizing Networks” on page A-17
(1)
(1)
for wireless update rate.
AP & GP: 140 ms
RTD Interface: 1 s
AP & GP: 11 updates per sec.
RTD Interface: 1 update per
sec.
Calculated Variables:
Mass / Volumetric Flow Rate:
22 updates per sec.
Energy Flow Rate: 22
updates per sec.
Totalized Flow: 1 update per
sec.
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
Mounting Position
Effects
Models Ultra, Ultra for Flow, Classic and Classic MV
3051SF_3, 4, 7, or D Zero shif ts up to ±1.25 inH2O (3,11 mbar), which can be
3051SF_1, 2, 5, or 6 DP Sensor: Zero shifts up to ±1.25 inH2O (3,11 mbar), which can be
GP/AP
Sensor:
zeroed
Span: no effect
zeroed
Span: no effect
Zero shifts to ±2.5 inH2O (6,22 mbar), which can be
zeroed
Span: no effect
Vibration Effect Less than ±0.1% of URL when tested per the requirements of IEC60770-1
field or pipeline with high vibration level (10-60 Hz 0.21mm displacement peak
amplitude / 60-2000 Hz 3g).
For Housing Style codes 1J, 1K, 1L, 2J, and 2M:
Less than ±0.1% of URL when tested per the requirements of IEC60770-1
field with general application or pipeline with low vibration level (10-60 Hz
0.15 mm displacement peak amplitude / 60-500 Hz 2g).
Power Supply Effect Less than ±0.005% of calibrated span per volt change in voltage at the
transmitter terminals
Electromagnetic
Compatibility (EMC)
T ransient Protection
(Option T1)
Meets all relevant requirements of EN 61326 and NAMUR NE-21.
(1) NAMUR NE-21 does not apply to wireless output code X.
(2) 3051SMV and 3051SF_1, 2, 3, 4, 5, 6, 7 requires shielded cable for
both temperature and loop wiring.
Meets IEEE C62.41.2-2002, Location Category B
6 kV crest (0.5 s - 100 kHz)
3 kA crest (8 × 20 microseconds)
6 kV crest (1.2 × 50 microseconds)
Meets IEEE C37.90.1-2002 Surge Withstand Capability
SWC 2.5 kV crest, 1.0 MHz wave form
(1) (2)
A-11
Annubar Flowmeter Series
3051SFA FUNCTIONAL
SPECIFICATIONS
Range and Sensor Limits Flowmeter with Coplanar Sensor Module
DP Sensor (3051SF_3, 4, or 7)
Range
1 0 inH2O (0 mbar) 25 inH2O (62,3 mbar)
2 0 inH2O (0 bar) 250 inH2O (0,62 bar)
3 0 inH2O (0 bar) 1000 inH2O (2,49 bar)
Flowmeter with MultiVariable Sensor Module
Range
1 0 inH2O (0 mbar) 25.0 inH2O (62,3 mbar)
2 0 inH2O (0 bar) 250.0 inH2O (0,62 bar)
3 0 inH2O (0 bar) 1000.0 inH2O (2,49 bar)
Range
3 GP
4 GP
(1) For SP Range 4 with DP Range 1, the URL is 2000 psi (137,9 bar).
(2) Inert Fill: Minimum pressure = 1.5 psia (0,10 bar) or -13.2 psig (-0,91 bar).
Lower (LRL) Upper (URL)
DP Sensor (3051SF1, 2, 5, or 6)
Lower (LRL) Upper (URL)
Static Pressure Sensor (GP/AP)
Lower (LRL) Upper (URL)
(2)
: -14.2 psig (0,98 bar)
AP: 0.5 psia (34,5 mbar)
(2)
: -14.2 psig (0,98 bar)
AP: 0.5 psia (34,5 mbar)
Reference Manual
00809-0100-4809, Rev CB
March 2012
(1)
GP: 800 psig (55,16 bar)
AP: 800 psia (55,16 bar)
GP: 3626 psig (250 bar)
AP: 3626 psia (250 bar)
Process Temperature RTD Interface (3051SF_1, 3, 5 or 7)
Lower (LRL) Upper (URL)
-328 °F (-200 °C) 1562 °F (850 °C)
(1) Transmitter is compatible with any Pt 100 RTD sensor. Examples of compatible RTDs include
Rosemount Series 68 and 78 RTD Temperature Sensors.
(1)
Minimum Span Limits Transmitter with Coplanar Sensor Module (Single Variable)
DP Sensor (3051SF_D, 3, 4 or 7)
Range
1 0.5 inH2O (1,24 mbar) 0.5 inH2O (1,24 mbar)
2 1.3 inH2O (3,11 mbar) 2.5 inH2O (6,23 mbar)
3 5.0 inH2O (12,4 mbar) 10.0 inH2O (24,9 mbar)
Transmitter with MultiVariable Sensor Module
Range
1 0.5 inH2O (1,24 mbar) 0.5 inH2O (1,24 mbar)
2 1.3 inH2O (3,11 mbar) 2.5 inH2O (6,23 mbar)
3 5.0 inH2O (12,4 mbar) 10.0 inH2O (24,9 mbar)
Range
3 4.0 psi (276 mbar) 8.0 psi (522 mbar)
4 18.13 psi (1,25 bar) 36.26 psi (2,50 bar)
Ultra & Ultra for Flow Classic
DP Sensor (3051SF_1, 2, 5, or 6)
Ultra for Flow Classic MV
Static Pressure Sensor (GP/AP)
Ultra for Flow Classic MV
A-12
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
Process Temperature RTD Interface
(3051SF_1, 3, 5, or 7)
Minimum Span = 50 °F (28 °C)
Service
3051SF_5, 6, 7, or D (Direct Process Variable Output):
Liquid, gas, and steam applications
3051SF_1, 2, 3, or 4 (Mass and Energy Flow Output):
Some fluid types are only supported by certain measurement types
Fluid Compatibility with Pressure and Temperature
Ordering
Code
Measurement
Type
1 DP / P/ T (Full
Compensation)
2 DP / P • • • •
3 DP / T • • — —
4 DP only • • — —
Compensation
Liquids
Fluid Types
Saturated
Steam
• • • •
• Available — Not
available
Superheated
Steam
Gas and
Natural Gas
4–20 mA/HART
Zero and Span Adjustment
Zero and span values can be set anywhere within the range.
Span must be greater than or equal to the minimum span.
Output
Two-wire 4–20 mA is user-selectable for linear or square root output.
Digital process variable superimposed on 4– 20 mA signal, available to any
host that conforms to the HART protocol.
Power Supply
External power supply required.
• 3051SF_D: 10.5 to 42.4 Vdc with no load
• 3051SF_D with Advanced HART Diagnostics Suite: 12 to 42.4 Vdc with
no load
• 3051SF_1-7: 12 to 42.4 Vdc with no load
Load Limitations
Maximum loop resistance is determined by the voltage level of the external
power supply, as described by:
A-13
Annubar Flowmeter Series
Voltage (Vdc)
Load (Ohms)
Operating
Region
1387
1000
500
0
10.5 20 30
42.4
Voltage (Vdc)
Load (Ohms)
Operating
Region
1322
1000
500
0
12.0 20 30
42.4
Maximum Loop Resistance = 43.5 * (Power Supply Voltage – 10.5)
The Field Communicator requires a minimum
loop resistance of 250
3051SF_1-7 and 3051SF_D with HART Diagnostics
Maximum Loop Resistance = 43.5 * (Power Supply Voltage – 12.0)
3051SF_D
for communication.
(option code DA2)
Reference Manual
00809-0100-4809, Rev CB
March 2012
The Field Communicator requires a minimum
loop resistance of 250
for communication.
Advanced HART Diagnostics Suite
(Option Code DA2)
The 3051SF provides Abnormal Situation Prevention indication for a
breakthrough in diagnostic capability. The 3051SF ASP Diagnostics Suite
for HART includes Statistical Process Monitoring (SPM), variable logging
with time stamp and advanced process alerts. The enhanced EDDL
graphic display provides an intuitive and user -fr ie nd ly inte rf ac e to be tter
visualize these diagnostics.
The integral SPM technology calculates the mean and standard deviation
of the process variable 22 times per second and makes them available to
the user. The 3051SF uses these values and highly flexible configuration
options for customization to detect many user-defined or application
specific abnormal situations (e.g. detecting plugged impulse lines and fluid
composition change). Variable logging with time stamp and advanced
process alerts capture valuable process and sensor data to enable quick
troubleshooting of application and installation issues.
A-14
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
FOUNDATION fieldbus
Power Supply
External power supply required; transmitters operate on 9.0 to 32.0 Vdc
transmitter terminal voltage.
Current Draw
17.5 mA for all configurations (including LCD display option)
OUNDATION fieldbus Parameters
F
Schedule Entries 14 (max.)
Links 30 (max.)
Virtual Communications Relationships (VCR) 20 (max.)
Standard Function Blocks
Resource Block
• Contains hardware, electronics, and diagnostic information.
Transducer Block
• Contains actual sensor measurement data including the sensor
diagnostics and the ability to trim the pressure sensor or recall factory
defaults.
LCD Block
• Configures the local display.
2 Analog Input Blocks
• Processes the measurements for input into other function blocks. The
output value is in engineering or custom units and contains a status
indicating measurement quality.
PID Block with Auto-tune
• Contains all logic to perform PID control in the field including cascade
and feedforward. Auto-tune capability allows for superior tuning for
optimized control performance.
Backup Link Active Scheduler (LAS)
The transmitter can function as a Link Active Scheduler if the current link
master device fails or is removed from the segment.
Software Upgrade in the Field
Software for the 3051SF with F
the field using the F
OUNDATION fieldbus Common Device Software
Download procedure.
PlantWeb Alerts
Enable the full power of the PlantWeb digital architecture by diagnosing
instrumentation issues, communicating ad visory, mainte nance, and failure
details, and recommending a solution.
Advanced Control Function Block Suite
(Option Code A01)
Input Selector Block
• Selects between inputs and generates an output using specific selection
strategies such as minimum, maximum, midpoint, average, or first
“good.”
Arithmetic Block
• Provides pre-defined application-based equations including flow with
partial density compensation, electronic remote seals, hydrostatic tank
gauging, ratio control, and others.
OUNDATION fieldbus is easy to upgrade in
A-15
Annubar Flowmeter Series
Signal Characterizer Block
• Characterizes or approximates any function that defines an input/output
relationship by configuring up to twenty X, Y coordinates. The block
interpolates an output value for a given input value using the curve
defined by the configured coordinates.
Integrator Block
• Compares the integrated or accumulated value from one or two variables
to pre-trip and trip limits and generates discrete output signals when the
limits are reached. This block is useful for calculating total flow, total
mass, or volume over time.
Output Splitter Block
•Splits the output of one PID or other control block so that the PID will
control two valves or other actuators.
Control Selector Block
• Selects one of up to three inputs (highest, middle, or lowest) that are
normally connected to the outputs of PID or other control function blocks.
Block Execution Time
Resource Transducer LCD Block Analog Input 1, 2 20 milliseconds
PID with Auto-tune 35 milliseconds
Input Selector 20 milliseconds
Arithmetic 20 milliseconds
Signal Characterizer 20 milliseconds
Integrator 20 milliseconds
Output Splitter 20 milliseconds
Control Selector 20 milliseconds
Reference Manual
00809-0100-4809, Rev CB
March 2012
Fully Compensated Mass Flow Block (Option Code H01)
Calculates fully compensated mass flow based on differential pressure
with external process pressure and temperature measurements over the
fieldbus segment. Configuration for the mass flow calculation is easily
accomplished using the Rosemount Engineering Assistant.
ASP Diagnostics Suite for F
OUNDATION fieldbus
(Option Code D01)
The 3051SF ASP Diagnostics Suite for F
OUNDATION fieldbus provides
Abnormal Situation Prevention indication and enhanced EDDL graphic
displays for easy visual analysis.
The integral Statistical Process Monitoring (SPM) technology calculates
the mean and standard deviation of the process variable 22 times per
second and makes them available to the user . The 3051SF uses these
values and highly flexible configuration options for customization to detect
many user-defined or application specific abnormal situations (e.g.
detecting plugged impulse lines and fluid composition change).
A-16
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
Wireless Self-Organizing Networks
Output
WirelessHART, 2.4 GHz DSSS.
Local Display
The optional five-digit LCD can display user-selectable information such
as primary variable in engineering units, percent of range, sensor modu le
temperature, and electronics temperature. Display updates at up to once
per minute.
Update Rate
WirelessHART, user selectable 8 sec. to 60 min.
Power Module
Field replaceable, keyed connection eliminates the risk of incorrect
installation, Intrinsically Safe Lithium-thionyl chloride Power Module with
polybutadine terephthalate (PBT) enclosure. Ten-year life at one minute
update rate.
(1) Reference conditions are 70 °F (21 °C), and routing data for three additional network devices.
NOTE: Continuous exposure to ambient temperature limits of
-40 °F or 185 °F (-40 °C or 85 °C) may reduce specified life by less than 20 percent.
(1)
Overpressure Limits Transmitters withstand the following limits without damage:
Coplanar Sensor Module (Single Variable)
(1)
DP
Range
1 2000 psi (137,9 bar)
2 3626 psi (250,0 bar)
3 3626 psi (250,0 bar)
(1) The overpressure limit of a DP Sensor with the P9 option is 4500
psig (310,3 bar). The overpressure limit of a DP Sensor with the
P0 option is 6092 psig (420 bar).
3051SF_3, 4, 7, or D
Coplanar MultiVariable Sensor Module (3051SF_1, 2, 5, or 6)
Static
Pressure
Range 3
GP/AP
Range 4
GP/AP
Range 1 Range 2 Range 3
1600 psi
(110,3 bar)
2000 psi
(137,9 bar)
Differential Pressure
1600 psi
(110,3 bar)
3626 psi
(250 bar)
1600 psi
(110,3 bar)
3626 psi
(250 bar)
Static Pressure Limits Coplanar Sensor Module
Operates within specifications between static line pressures of:
DP Sensor
Range
1 0.5 psia to 2000 psig (0,03 to 137,9 bar)
2 0.5 psia to 3626 psig (0,03 to 150 bar)
3 0.5 psia to 3626 psig (0,03 to 150 bar)
(1) The static pressure limit of a DP Sensor wit h the P9 option i s 4500
psig (310,3 bar). The static pressure limit of a DP Sensor with the
P0 option is 6092 psig (420 bar).
3051SF_3, 4, 7, or D
(1)
A-17
Annubar Flowmeter Series
Coplanar MultiVariable Sensor Module (3051SF_1, 2, 5, or 6)
Operates within specifications between static line pressures of 0.5 psia (0,03 bar) and the values
in the table below:
Static
Pressure
Range 3
GP/AP
Range 4
GP/AP
Range 1 Range 2 Range 3
800 psi
(57,91 bar)
2000 psi
(137,9 bar)
Burst Pressure Limits Coplanar Sensor Module
10000 psig (689,5 bar)
Temperature Limits Ambient
-40 to 185 °F (-40 to 85 °C)
With LCD display
With option code P0: -20 to 185 °F (-29 to 85 °C)
(1) LCD display may not be readable and LCD upda tes will be slower
at temperatures below -4 °F (-20 °C).
(1)
: -40 to 175 °F (-40 to 80 °C)
Differential Pressure
800 psi
(57,91 bar)
3626 psi
(250 bar)
Reference Manual
00809-0100-4809, Rev CB
March 2012
800 psi
(57,91 bar)
3626 psi
(250 bar)
Storage
-50 to 185 °F (-46 to 85 °C)
With LCD display: -40 to 185 °F (-40 to 85 °C)
With Wireless Output: -40 to 185 °F (-40 to 85 °C)
Process Temperature Limits
For 3051SFA Temperature Limits, see page A-63.
At atmospheric pressures and above:
Humidity Limits 0–100% relative humidity
(1)
(1)
3
(0,08 cm3)
Turn-On Time
When power is applied to the transmitter during startup,
performance will be within specifications per the time period
described below:
Transmitter Turn-On Time (Typical)
3051S, 3051SF_D 2 seconds
Diagnostics 5 seconds
3051SMV, 3051SF_1-7 5 seconds
(1) Does not apply to wireless option code X.
Volumetric Displacement Less than 0.005 in
Damping
Analog output response time to a step change is user-selectable
from 0 to 60 seconds for one time constant. For 3051SF_1-7,
each variable can be individually adjusted. Software damping is in
addition to sensor module response time.
(1) Does not apply to wireless option code X.
A-18
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
Failure Mode Alarm HART 4-20 mA (output option code A)
If self-diagnostics detect a gross transmitter failure, the analog signal will be
driven offscale to alert the user. Rosemount standard (default), NAMUR, and
custom alarm levels are available (see Alarm Configuration below).
High or low alarm signal is software-selectable or hardware-select able via the
optional switch (option D1).
Alarm Configuration
High Alarm Low Alarm
Default 21.75 mA 3.75 mA
NAMUR compliant
Custom levels
(1) Analog output levels are compliant with NAMUR
recommendation NE 43, see option codes C4 or C5.
(2) Low alarm must be 0.1 mA less than low sa turati on and high
alarm must be 0.1 mA greater than high saturation.
(1)
(2)
22.5 mA 3.6 mA
20.2 - 23.0 mA 3.4 - 3.8 mA
Safety-Certified Transmitter Failure
Values
Safety accuracy: 2.0%
Safety response time: 1.5 seconds
(1) Does not apply to wireless option code X.
(2) A 2% variation of the transmitter mA output is allowed before a
(1)
(2)
safety trip. T rip values in the DCS or safety logic solver should be
derated by 2%.
3051SFA PHYSICAL
SPECIFICATIONS
Electrical Connections
1
/2–14 NPT, G1/2, and M20 × 1.5 conduit. HART interface connections fixed to
terminal block for Output code A and X.
Process Connections
Coplanar Sensor Module
Standard1/4-18 NPT on 2 1/8-in. centers
Process-Wetted Parts For 3051SFA wetted parts, see “Annubar Sensor Material” on page A-63.
Process Isolating Diaphragms
Coplanar Sensor Module
316L SST (UNS S31603), Alloy C-276 (UNS N10276), Alloy 400
(UNS N04400), T antalum (UNS R05440), Gold-Plated Alloy 400,
Gold-plated 316L SST
A-19
Annubar Flowmeter Series
Drain/Vent Valves
316 SST, Alloy C-276, or Alloy 400/K-500 material
(Drain vent seat: Alloy 400, Drain vent stem: Alloy K-500)
Process Flanges and Adapters
Plated carbon steel
SST: CF-8M (Cast 316 SST) per ASTM A743
Cast C-276: CW-12MW per ASTM A494
Cast Alloy 400: M-30C per ASTM A494
Non-Wetted Parts Electronics Housing
Low-copper aluminum alloy or CF-8M (Cast 316 SST)
NEMA 4X, IP 66, IP 68 (66 ft (20 m) for 168 hours)
Note: IP 68 not available with Wireless Output.
Paint for Aluminum Housing
Polyurethane
Coplanar Sensor Module Housing
SST: CF-3M (Cast 316L SST)
Reference Manual
00809-0100-4809, Rev CB
March 2012
Bolts
Plated carbon steel per ASTM A449, Type 1
Austenitic 316 SST per ASTM F593
ASTM A453, Class D, Grade 660 SST
ASTM A193, Grade B7M alloy steel
ASTM A193, Class 2, Grade B8M SST
Alloy K-500
Sensor Module Fill Fluid
Silicone or inert halocarbon
Cover O-rings
Buna-N
Wireless Antenna
PBT/ polycarbonate (PC) integrated omnidirectional antenna
Power Module
Field replaceable, keyed connection eliminates the risk of incorrect
installation, Intrinsically Safe Lithium-thionyl chloride Power Module with PBT
enclosure.
A-20
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
3051CFA ORDERING
INFORMATION
Table A-4. Rosemount 3051CFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model Product Description
3051CFA Annubar Flowmeter
Measurement Type
Standard Standard
D Differential Pressure ★
Fluid Type
Standard Standard
L Liquid ★
G Gas ★
S Steam ★
Line Size
Standard Standard
020 2-in. (50 mm) ★
025 21/2-in. (63.5 mm) ★
030 3-in. (80 mm) ★
035 31/2-in. (89 mm) ★
040 4-in. (100 mm) ★
050 5-in. (125 mm) ★
060 6-in. (150 mm) ★
070 7-in. (175 mm) ★
080 8-in. (200 mm) ★
100 10-in. (250 mm) ★
120 12-in. (300 mm) ★
Expanded
140 14-in. (350 mm)
160 16-in. (400 mm)
180 18-in. (450 mm)
200 20-in. (500 mm)
240 24-in. (600 mm)
300 30-in. (750 mm)
360 36-in. (900 mm)
420 42-in. (1066 mm)
480 48-in. (1210 mm)
600 60-in. (1520 mm)
720 72-in. (1820 mm)
780 78-in (1950 mm)
840 84-in. (2100 mm)
900 90-in. (2250 mm)
960 96-in (2400 mm)
Pipe I.D. Range
Standard Standard
C Range C from the Pipe I.D. table ★
D Range D from the Pipe I.D. table ★
Expanded
A Range A from the Pipe I.D. table
B Range B from the Pipe I.D. table
E Range E from the Pipe I.D. table
Z Non-standard Pipe I.D. Range or Line Sizes greater than 12 inches
A-21
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
Table A-4. Rosemount 3051CFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Pipe Material / Mounting Assembly Material
Standard Standard
C Carbon steel (A105) ★
S 316 Stainless Steel ★
0 No Mounting (Customer Supplied) ★
Expanded
G Chrome-Moly Grade F-11
N Chrome-Moly Grade F-22
J Chrome-Moly Grade F-91
Piping Orientation
Standard Standard
H Horizontal Piping ★
D Vertical Piping with Downwar ds Flow ★
U Vertical Piping with Upwards Flow ★
Annubar Type
Standard Standard
P Pak-Lok ★
F Flanged with opposite side support ★
Expanded
L Flange-Lok
G Gear-Drive Flo-Tap
M Manual Flo-Tap
Sensor Material
Standard Standard
S 316 Stainless Steel ★
Expanded
H Alloy C-276
Sensor Size
Standard Standard
1 Sensor size 1 — Line sizes 2-in. (50 mm) to 8-in. (200 mm) ★
2 Sensor size 2 — Line sizes 6-in. (150 mm) to 96-in. (2400 mm) ★
3 Sensor size 3 — Line sizes greater than 12-in. (300 mm) ★
Mounting Type
Standard Standard
T1 Compression or Threaded Connection ★
A1 150# RF ANSI ★
A3 300# RF ANSI ★
A6 600# RF ANSI ★
D1 DN PN16 Flange ★
D3 DN PN40 Flange ★
D6 DN PN100 Flange ★
Expanded
(1)
A9
(1)
AF
(1)
AT
R1 150# RTJ Flange
R3 300# RTJ Flange
R6 600# RTJ Flange
(1)
R9
(1)
RF
(1)
RT
900# RF ANSI
1500# RF ANSI
2500 # RF ANSI
900# RTJ Flange
1500# RTJ Flange
2500# RTJ Flange
March 2012
A-22
Reference Manual
00809-0100-4809, Rev CB
March 2012
Table A-4. Rosemount 3051CFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Opposite Side Support or Packing Gland
Standard Standard
0 No opposite side support or packing gland (Required for Pak-Lok and Flange-Lok models) ★
Opposite Side Support – Required for Flanged Models
C NPT Threaded Opposite Support Assembly – Extended Tip ★
D Welded Opposite Support Assembly – Extended Tip ★
Expanded
Packing Gland – Required for Flo-Tap Models
Packing Gland Material Rod Material Packing Material
J Stainless Steel Packing Gland / Cage Nipple Carbon Steel PTFE
K Stainless Steel Packing Gland / Cage Nipple Stainless Steel PTFE
L Stainless Steel Packing Gland / Cage Nipple Carbon Steel Graphite
N Stainless Steel Packing Gland / Cage Nipple Stainless Steel Graphite
R Alloy C-276 Packing Gland / Cage Nipple Stainless Steel Graphite
Isolation Valve for Flo-Tap Models
Standard Standard
0 Not Applicable or Customer Supplied ★
Expanded
1 Gate Valve, Carbon Steel
2 Gate Valve, Stainless Steel
5 Ball Valve, Carbon Steel
6 Ball Valve, Stainless Steel
7 Ball Valve, Alloy C-276
Temperature Measurement
Standard Standard
T Integral RTD – not available with Flanged model greater than class 600# ★
0 No Temper ature Sensor ★
Expanded
R Remote Thermowell and RTD
Transmitter Connection Platform
Standard Standard
3 Direct-mount, Integral 3-valve Manifold– not available with Flanged model greater than class 600 ★
5 Direct -mount, 5-valve Manifold – not available with Flanged model greater than class 600 ★
7 Remote-mount NPT Connections (1/2-in. NPT) ★
Expanded
6 Direct-mount, high temperature 5-valve Manifold – not available with Flanged model greater than class 600
8 Remote-mount SW Connections (1/2-in.)
Differential Pressure Range
Standard Standard
1 0 to 25 in H2O (0 to 62,3 mbar) ★
2 0 to 250 in H2O (0 to 623 mbar) ★
3 0 to 1000 in H2O (0 to 2,5 bar) ★
Transmitter Output
Standard Standard
A 4–20 mA with digital signal based on HART Protocol ★
F FOUNDATION fieldbus Protocol ★
(2)
W
Expanded
M Low-Power, 1-5 Vdc with Digital Signal Based on HART Protocol
Profibus PA Protocol ★
Annubar Flowmeter Series
A-23
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
March 2012
Table A-4. Rosemount 3051CFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Transmitter Housing Material Conduit Entry Size
Standard Standard
A Aluminum
B Aluminum M20 x 1.5 ★
J SST
K SST M20 x 1.5 ★
Expanded
D Aluminum G1/2
M SST G1/2
Transmitter Performance Class
Standard Standard
1 1.6% flow rate accuracy, 8:1 flow turndown, 5-yr. stability ★
1
/2-14 NPT ★
1
/2-14 NPT ★
Options (Include with selected model number)
Pressure Testing
Expanded
(3)
P1
(3)
PX
Special Cleaning
Expanded
P2 Cleaning for Special Services
PA Cleaning per ASTM G93 Level D (Section 11.4)
Material Testing
Expanded
V1 Dye Penetrant Exam
Material Examination
Expanded
V2 Radiographic Examination
Flow Calibration
Expanded
W1 Flow Calibration (Average K)
Special Inspection
Standard Standard
QC1 Visual & Dimensional Inspection with Certificate ★
QC7 Inspection & Performance Certificate ★
Surface Finish
Standard Standard
RL Surface finish for Low Pipe Reynolds # in Gas & Steam ★
RH Surface finish for High Pipe Reynolds # in Liquid ★
Material Traceability Certification
Standard Standard
(4)
Q8
Code Conformance
Expanded
J2 ANSI/ASME B31.1
J3 ANSI/ASME B31.3
Materials Conformance
Expanded
(6)
J5
Country Certification
Standard Standard
J6 European Pressure Directive (PED) ★
Expanded
J1 Canadian Registration
Hydrostatic Testing with Certificate
Extended Hydrostatic Testing
Material Traceability Certification per EN 10474:2004 3.1 ★
(5)
NACE MR-0175 / ISO 15156
A-24
Reference Manual
00809-0100-4809, Rev CB
March 2012
Table A-4. Rosemount 3051CFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Installed in Flanged Pipe Spool Section
Expanded
H3 150# Flanged Connection with Rosemount Standard Length and Schedule
H4 300# Flanged Connection with Rosemount Standard Length and Schedule
H5 600# Flanged Connection with Rosemount Standard Length and Schedule
Instrument Connections for Remote Mount Options
Standard Standard
G2 Needle Valves, Stainless Steel ★
G6 OS&Y Gate Valve, Stainless Steel ★
Expanded
G1 Needle Valves, Carbon Steel
G3 Needle Valves, Alloy C-276
G5 OS&Y Gate Valve, Carbon Steel
G7 OS&Y Gate Valve, Alloy C-276
Special Shipment
Standard Standard
Y1 Mounting Hardware Shipped Separately ★
Special Dimensions
Expanded
VM Variable Mounting
VT Variable Tip
VS Variable length Spool Section
PlantWeb Control Functionality
Standard Standard
(7)
A01
PlantWeb Diagnostic Functionality
Standard Standard
(7)
D01
Product Certifications
Standard Standard
C6 CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 ★
E5 FM Explosion-proof, Dust Ignition-proof ★
(8)
E7
E8 ATEX Flameproof, Dust ★
(8)
I1
I5 FM Intrinsically Safe, Division 2 ★
IA ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus protocol only ★
K5 FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5 and I5) ★
(8)
K6
(8)
K8
KB FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of K5 and C6) ★
(8)
KD
(8)
N1
Alternate Transmitter Material of Construction
Standard Standard
L1 Inert Sensor Fill Fluid Note: Silicone fill fluid is standard. ★
L2 Graphite-Filled (PTFE) O-ring ★
LA Inert Sensor Fill Fluid and Graphite-Filled (PTFE) O-ring ★
Display and Interface Options
Standard Standard
(9)
M4
M5 LCD Display ★
FOUNDATION fieldbus Advanced Control Function Block Suite ★
FOUNDATION fieldbus Diagnostics Suite ★
IECEx Flameproof, Dust Ignition-proof ★
ATEX Intrinsic Safety ★
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E6 and I6) ★
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E8, I1 and N1) ★
FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of K5, C6, I1, and E8) ★
ATEX Type n ★
LCD Display with Local Operator Interface ★
Annubar Flowmeter Series
A-25
Reference Manual
00809-0100-4809, Rev CB
Annubar Flowmeter Series
Table A-4. Rosemount 3051CFA Annubar Flowmeter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Transmitter Calibration Certification
Standard Standard
Q4 Calibration Certificate for Transmitter ★
Quality Certification for Safety
Standard Standard
(11)
QS
Transient Protection
Standard Standard
(10)
T1
Manifold for Remote Mount Option
Standard Standard
F2 3-Valve Manifold, Stainless Steel ★
F6 5-Valve Manifold, Stainless Steel ★
Expanded
F1 3-Valve Manifold, Carbon Steel
F3 3-Valve Manifold, Alloy C-276
F5 5-Valve Manifold, Carbon Steel
F7 5-Valve Manifold, Alloy C-276
Lower Power Output
Standard Standard
(11)
C2
Alarm Limit
Standard Standard
(11)(12)
C4
(11)(12)
CN
Ground Screw
Standard Standard
(13)
V5
Typical Model Number: 3051CFA D L 060 D C H P S 2 T1 0 0 0 3 2 A A 1
(1) Available in remote mount applications only.
(2) Option code M4 - LCD Display with Local Operator Interface req uired for local addressing and configuration.
(3) Applies to assembled flowmeter only, mounting not tested.
(4) Instrument Connections for Remote Mount Options and Isolation Valves for Flo-ta p Models are not included in the Material Traceability Certification.
(5) Not available with Transmitter Connection Platform 6.
(6) Materials of Construction comply with metallurgical requ irements within NACE MR0175/ISO fo r sour oil field production enviro nments. Environmenta l limits
(7) Only valid with F
(8) Not available with Low Power code M.
(9) Available only with output co de W - Profibus PA.
(10) The T1 option is not needed with FISCO Product Certifications, transient protection is included with the FISCO Product Certification code IA.
(11) Not available with F
(12) NAMUR-Compliant operation is pre-set at the factory and cannot be changed to standard operation in the field.
(13) The V5 option is not needed with the T1 option; external ground screw assembly is included with the T1 option.
Certificate of FMEDA data ★
Transient terminal block ★
0.8-3.2 Vdc Output with Digital Signal Based on Hart Protocol ★
NAMUR Alarm and Saturation Levels, High Alarm ★
NAMUR Alarm and Saturation Levels, Low Alarm ★
External Ground Screw Assembly ★
apply to certain materials. Consult latest standard for details. Selected mat erials also conform to NACE MR0103 for sour refining environments.
OUNDATION fieldbus Output Code F.
OUNDATION fieldbus (Output Code F) or Profibus (Output Code W).
March 2012
A-26
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
3051CFA
PERFORMANCE
SPECIFICATIONS
3051CFA FUNCTIONAL
SPECIFICATIONS
Performance assumptions include: measured pipe I.D, transmitter is trimmed
for optimum flow accuracy, and performance is dependent on application
parameters.
Table 1. Flow Perfor mance - Flow Reference Accuracy
3051CFA Annubar Flowmeter
Ranges 2-3 ±1.60% of Flow Rate at 8:1 flow turndown
Range and Sensor Limits
Table 2. 3051CF Range and Sensor Limits
Range 3051CF Minimum Span Range and Sensor Limits
1
0.5 inH2O (1,2 mbar) 0 to 25 inH2O (62,3 mbar)
2
2.5 inH2O (6,2 mbar) 0 to 250 inH2O (0,63 bar)
3
10 inH2O (24,9 mbar) 0 to 1000 inH2O (2,49 bar)
Zero and Span Adjustment Requirements
(HART and Low Power)
Zero and span values can be set anywhere within the range limits state d in
Table 2 and Table 3.
Span must be greater than or equal to the minimum span stated in Table 2
and Table 3.
Service
Liquid, gas, and vapor applications
4–20 mA (Output Code A)
Output
Two-wire 4–20 mA, user-selectable for linear or square root output. Digital
process variable superimposed on 4–20 mA signal, available to any host that
conforms to the HART protocol.
Power Supply
External power supply required. Standard transmitter (4–20 mA) opera tes on
10.5 to 55 Vdc with no load.
A-27
Annubar Flowmeter Series
Voltage (Vdc)
Load (Ohms)
Communication requires a minimum
loop resistance of 250 ohms.
(1) For CSA approval, power supply must not exceed 42.4 V.
Max. Loop Resistance = 43.5 (Power Supply Voltage – 10.5)
Operating
Region
Load Limitations
Maximum loop resistance is determined by the voltage level of the external
power supply, as described by:
Reference Manual
00809-0100-4809, Rev CB
March 2012
FOUNDATION fieldbus
(output code F) and
Profibus (output code W)
Power Supply
External power supply required; transmitters operate on 9.0 to 32.0 Vdc
transmitter terminal voltage.
Current Draw
17.5 mA for all configurations (including LCD display option)
OUNDATION fieldbus Function Block Execution Times
F
Block Execution Time
Resource Transducer LCD Block Analog Input 1, 2 30 milliseconds
PID 45 milliseconds
Input Selector 30 milliseconds
Arithmetic 35 milliseconds
Signal Characterizer 40 milliseconds
Integrator 35 milliseconds
F
OUNDATION fieldbus Parameters
Schedule Entries 7 (max.)
Links 20 (max.)
Virtual Communications Relationships (VCR) 12 (max.)
A-28
Reference Manual
00809-0100-4809, Rev CB
March 2012
Annubar Flowmeter Series
Standard Function Blocks
Resource Block
Contains hardware, electronics, and diagnostic information.
Transducer Block
Contains actual sensor measurement data including the sensor
diagnostics and the ability to trim the pressure sensor or recall factory
defaults.
LCD Block
Configures the local display.
2 Analog Input Blocks
Processes the measurements for input into other function blocks. The
output value is in engineering units or custom and contains a status
indicating measurement quality.
PID Block
Contains all logic to perform PID control in the field including cascade and
feedforward.
Backup Link Active Scheduler (LAS)
The transmitter can function as a Link Active Scheduler if the current link
master device fails or is removed from the segment.
Advanced Control Function Block Suite (Option Code A01)
Input Selector Block
Selects between inputs and generates an output using specific selection
strategies such as minimum, maximum, midpoint, average, or first “good.”
Arithmetic Block
Provides pre-defined application-based equations including flow with
partial density compensation, electronic remote seals, hydrostatic tank
gauging, ratio control, and others.
Signal Characterizer Block
Characterizes or approximates any function that defines an input/output
relationship by configuring up to twenty X, Y coordinates. The block
interpolates an output value for a given input value using the curve defined
by the configured coordinates.
Integrator Block
Compares the integrated or accumulated value from one or two variables
to pre-trip and trip limits and generates discrete output signals when the
limits are reached. This block is useful for calculating total flow, total mass,
or volume over time.
OUNDATION fieldbus Diagnostics Suite (Option Code D01)
F
The 3051C F
Prevention (ASP) indication. The integral statistical process monitoring
(SPM) technology calculates the mean and standard deviation of the
process variable 22 times per second. The 3051C ASP algorithm uses
these values and highly flexible configuration options for customization to
many user-defined or application specific abnormal situations. The
detection of plugged impulse lines is the first available predefined
application.
OUNDATION fieldbus Diagnostics provide Abnormal Situation
A-29
Annubar Flowmeter Series
Reference Manual
00809-0100-4809, Rev CB
March 2012
Low Power (Output
Code M)
Output
Three wire 1–5 Vdc or 0.8–3.2 Vdc (Option Code C2) user-selectable output.
Also user selectable for linear or square root output configuration. Digital
process variable superimposed on voltage signal, available to any host
conforming to the HART protocol. Low-power transmitter operates on 6–12
Vdc with no load.
Power Consumption
3.0 mA, 18–36 mW
Minimum Load Impedance
100 k (V
Indication
Optional 5-digit LCD display
Overpressure Limits
Rosemount 3051CF
• Range 0: 750 psi (51,7 bar)
• Range 1: 2000 psig (137,9 bar)
• Ranges 2–5: 3626 psig (250 bar)
4500 psig (310,3 bar) for option code P9
Static Pressure Limit
Operates within specifications between static line pressures of 0.5 psia and
3626 psig.
Range 1: 0.5 psia and 2000 psig (3, 4 bar and 137, 9 bar)
wiring)
out
Burst Pressure Limits
Burst pressure on Coplanar process flange is 10000 psig (69 MPa).
Failure Mode Alarm
Output Code A
If self-diagnostics detect a gross transmitter failure, the analog signal will
be driven either below 3.75 mA or to 21.75 mA to alert the user.
NAMUR-compliant values are available, option code C4. High or low alarm
signal is user-selectable by internal jumper.
Output Code M
If self-diagnostics detect a gross transmitter failure, the analog signal will
be driven either below 0.94 V or above 5.4 V to alert the user (below 0.75
V or above 4.4 V for Option C2). High or low alarm signal is
user-selectable by internal jumper.
Output Code F and W
If self-diagnostics detect a gross transmitter failure, that information gets
passed as a status along with the process variable.
A-30
Loading...