Rosemount BINOS 100 Series Analyzers including OXYNOS 100 and HYDROS 100-Software Version 5.1x-3rd Ed. Manuals & Guides

Rosemount Analytical

Microprocessor - Controlled Gas Analyzers

Operation Manual

Series 100

BINOS® 100

BINOS® 100 F

BINOS® 100 M

BINOS® 100 2M

OXYNOS® 100

HYDROS® 100

Software Version 5.1x

3. Edition 01/2003

ETC00781(3) Series 100 e 01/2003

Catalog - No.: ETC00781

Rosemount Analytical

This Maintenance & Operation Manual includes information about the operation of the instrument as
well as additional indications and notes regarding maintenance, troubleshooting and repair.

Use qualified personnel only for troubleshooting, component replacement and internal
adjustments.

Fisher-Rosemount MFG GmbH & Co. OHG assumes no liability for any omissions or errors in this

manual.
Any liability for direct or consequential damages - which might occur in connection with the delivery or
the use of this manual - is definitely excluded to the extend permitted by applicable law.

This instrument has left the factory in accordance to all applicable safety regulations.
To maintain this operating condition, the user must strictly follow the instructions and consider the

warnings in this manual or provided on the instrument.

Misprints and alterations reserved

©

2001 by FISHER-ROSEMOUNT MFG GmbH & Co. OHG (PAD/ETC)

1. Edition: 10/2001 3. Edition: 01/2003

2. Edition: 11/2002

Read this operation manual carefully before attempting to operate the analyzer !
For expedient handling of reports of defects, please include the model and serial number
which are printed on the instrument identity plate.

Look for the error check list too (see chapter 32. of this manual)

Fisher - Rosemount MFG GmbH & Co. OHG

European Technology Center

Process Analytic Division

Industriestrasse 1

D - 63594 Hasselroth • Germany

Phone + 49 (6055) 884-0

Telefax + 49 (6055) 884-209

Internet: http://www.processanalytic.com

ETC00781(3) Series 100 e 01/2003

SERIAL INTERFACE (OPTION)

NUMERICAL REPRESENTATION / BLOCK PARITY CHECK

Rosemount Analytical

12.4.6 Numerical Representations

Telegrams may contain integers or real numbers. The formats for these numbers are subject to
the following restrictions.

Integers: - maximum value = 216 - 1

- positive numbers only accepted

- no decimal points allowed

Real: - maximum of 6 digits accepted

- no alphabetic characters (e.g. 2.2E-6) allowed

- analyzer output is 6 - digit real numbers

12.4.7 Block Parity Check

The master control computer may insert a message length parity byte into telegrams. These
invariably consist of two characters.

The message - length parity byte is the cumulatively EXCLUSIVE - OR correlation of all previously
transmitted characters of the telegram line. Representation is in hexadecimal format. For example,
if the decimal value should be decimal 13, this will be represented by the two characters “OD”, i.e.,
030H and 044H.

The verification procedure may be enabled or disabled at the analyzer (see chapter 12.3.4).

12 - 10

ETC00781(3) Series 100 e 01/2003

Rosemount Analytical

12.5 Instruction Syntax

Code definitions:

RP: receive parameters analyzer is accepting values
SP: send parameters analyzer is sending values
RI: receive instructions
k: channel numbers 0 to 2
m: range number
w: value

SERIAL INTERFACE (OPTION)

INSTRUCTION SYNTAX

<ID>: analyzer ID - no. for RS 485 mode of operation; follows start character
LPB: message - length parity byte
<CR>: terminate character

Receipt of any instruction codes not listed in the following section will be acknowledged by
transmittal of status code 106. Future expansions will make use of code numbers not currently in
use.

ETC00781(3) Series 100 e 01/2003

12 - 11

SERIAL INTERFACE (OPTION)

INSTRUCTION LIST

12.5.1 Instruction Listing

Instruction syntax: Instruction description:

$ID;001;k;LPB<CR> RI stand-by status (all valves closed)

$ID;002;k;LPB<CR> RI sample gas valve open

$ID;003;k;LPB<CR> RI zero gas valve open

$ID;005;m;k;LPB<CR> RI span gas valve open

$ID;006;LPB<CR> RI on - line status

$ID;007;LPB<CR> RI off - line status

$ID;008;LPB<CR>

*)

$ID;009;w;LPB<CR>

SP pump status

*)

RI pump status

*)

*)

w=0: pump Off, w=1: pump On

Rosemount Analytical

$ID;011;m;k;LPB<CR> SP at full scale range

$ID;013;k;LPB<CR> SP t

$ID;014;w;k;LPB<CR> RP t

(response time)

90

(response time)

90

$ID;017;k;LPB<CR> SP preflushing period (zero gas)

$ID;018;w;k;LPB<CR> RP preflushing period (zero gas)

$ID;019;k;LPB<CR> SP preflushing period (span gas)

$ID;020;w;k;LPB<CR> RP preflushing period (span gas)

$ID;023;k;LPB<CR> SP concentration

$ID;028;m;k;LPB<CR> SP span gas concentration

$ID;029;m;w;k;LPB<CR> RP span gas concentration

$ID;030;LPB<CR> SP status messages

$ID;031;t;LPB<CR> SP serial number (t=0, max. 10 characters)

channel identification (t=1: ch.1, t=2: ch. 2)

$ID;603;k;LPB<CR> SP gas component

$ID;604;k;LPB<CR> RI automatic zeroing

$ID;605;k;LPB<CR> RI automatic spanning

$ID;606;0;LPB<CR> RI automatic zeroing & spanning

$ID;626;LPB<CR> SP E-Prom / Software version

$ID;627;LPB<CR> SP failure message (possible error batt. is

clearing by read out)

$ID;645;0;LPB<CR> SP pressure value

$ID;646;w;LPB<CR> SP solenoid valve status (w=1: samplegas valve,

w=2: zerogas valve, w=4: spangas 1, w=8: spangas 2)

*) BINOS® 100 2M/F from program version 5.0 is required

12 - 12

ETC00781(3) Series 100 e 01/2003

Rosemount Analytical

SERIAL INTERFACE (OPTION)

RESPONSE TELEGRAMS

12.5.2 Response Telegrams

Response telegrams follow with the same syntax as the appropiate (SP-) commands (see 12.5).

12.5.2.1Status Messages (Instruction 030)

The response telegram for instruction

“$ID;030;LPB<CR> SP Status messages”

shows as follows:

$ID;030;a;b;c;LPB<CR>

This means:

a: OK-Status 0 = Relay without power 1 = Relay active

b: Value of variable “calibration” 0 = Relay without power >0 = Relay active

b Meaning

0 No Calibration
1 Zeroing channel 1
2 Zeroing channel 2
3 Zeroing channel 1 + 2
4 Spanning channel 1
5 Spanning channel 2
6 Spanning channel 1 + 2
7 Spanning channel 1 first, then channel 2
8 reserved
9 reserved
10 Waiting for flushing time and t90 response time

c: Gas sampling pump

*)

BINOS® 100 2M/F from program version 5.0 is required

ETC00781(3) Series 100 e 01/2003

*)

0 = Relay without power 1 = Relay active

(pump OFF) (pump ON)

12 - 13

SERIAL INTERFACE (OPTION)

RESPONSE TELEGRAMS

Rosemount Analytical

12.5.2.2 Pump Status (Instruction 008)

*)

The response telegram for instruction

“$ID;008;LPB<CR> SP Pump status”

shows as follows:

$ID;008;w;LPB<CR>

with w = pump status 0: Pump Off 1: Pump On

12 - 14

*) BINOS® 100 2M/F from program version 5.0 is required

ETC00781(3) Series 100 e 01/2003