Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702 Wireless Discrete
Transmitter
www.rosemount.com
Reference Manual
NOTICE
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Rosemount 702 Wireless
Discrete Transmitter
Rosemount 702 Hardware Revision
HART® Device Revision
Field Communicator Field Device Revision
Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure to thoroughly understand the contents before
installing, using, or maintaining this product.
The United States has two toll-free assistance numbers and one international number.
Customer Central
1-800-999-9307 (7:00 a.m. to 7:00 P.M. CST)
National Response Center
1-800-654-7768 (24 hours a day)
Equipment service needs
International
1-(952) 906-8888
The products described in this document are NOT designed for nuclear-qualified
applications.
Using non-nuclear qualified products in applications that require nuclear-qualified hardware
or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact a Emerson Process
Management Sales Representative.
1
1
Dev v1, DD v4
www.rosemount.com
Rosemount 702 Wireless Temperature Transmitter may be protected by one or more U.S.
Patents pending. Other foreign patents pending.
Rosemount 702
NOTICE
NOTICE
Reference Manual
00809-0100-4702, Rev AA
September 2007
Explosions could result in death or serious injury:
Installation of this transmitter in an explosive environment must be in accordance
with the appropriate local, national, and international standards, codes, and
practices. Please review the approvals section of the 702 reference manual for any
restrictions associated with a safe installation.
• Before connecting a Field Communicator in an explosive atmosphere, ensure the
instruments are installed in accordance with intrinsically safe or non-incendive
field wiring practices.
Process leaks may cause harm or result in death.
• Install and tighten process connectors before applying pressure.
Electrical shock can result in death or serious injury.
• Avoid contact with the leads and terminals. High voltage that may be present on
leads can cause electrical shock.
The Rosemount 702 and all other wireless devices should be installed only after the
1420 Wireless Gateway has been installed and is functioning properly. Wireless devices
should also be powered up in order of proximity from the 1420 Wireless Gateway,
beginning with the closest. This will result in a simpler and faster network installation.
Shipping considerations for wireless products (Lithium Batteries):
The unit was shipped to you without the battery installed. Please remove the battery pack
from the unit prior to shipping.
Primary lithium batteries are regulated in transportation by the U. S. Department of
Transportation, and are also covered by IATA (International Air Transport Association),
ICAO (International Civil Aviation Organization), and ARD (European Ground
Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure
compliance with these or any other local requirements. Please consult current regulations
and requirements before shipping.
The battery pack with the wireless unit contains two “C” size primary
lithium/thionyl chloride batteries. Each battery contains approximately 2.5
grams of lithium, for a total of 5 grams in each pack. Under normal conditions,
the battery materials are self-contained and are not reactive as long as the
batteries and the pack integrity are maintained. Care should be taken to
prevent thermal, electrical or mechanical damage. Contacts should be
protected to prevent premature discharge.
Battery hazards remain when cells are discharged.
Batteries should be stored in a clean and dry area. For maximum battery life,
storage temperature should not exceed 30° C.
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Table of Contents
Shipping considerations for wireless products (Lithium Batteries): 0-2
SECTION 1
Overview
SECTION 2
Configuration
SECTION 3
Mounting
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Return of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Switch Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Device Sensor Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Device Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
HART Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Fast Key Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Remove Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Direct Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Remote Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Ground the Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
SECTION 4
Commissioning
SECTION 5
Operation and
Maintenance
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Verify Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
LCD Screen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Startup Screen Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Diagnostic Button Screen Sequence . . . . . . . . . . . . . . . . . . . . . . . 5-3
Network Diagnostic Status Screens . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Device Diagnostic Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
TOC-1
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
APPENDIX A
Specifications and
Reference Data
APPENDIX B
Product Certifications
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Notes: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-5
Approved Manufacturing Locations . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
European Directive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Telecommunication Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Ordinary Location Certification for FM . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Hazardous Locations Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
TOC-2
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Section 1 Overview
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-2
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-3
Return of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-5
SAFETY MESSAGES Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Warnings
Failure to follow these installation guidelines could result in death or
serious injury.
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
• Before connecting a 375 Field Communicator in an explosive atmosphere, make
sure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Process leaks could result in death or serious injury.
• Do not remove the thermowell while in operation.
• Install and tighten thermowells and switches before applying pressure
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
www.rosemount.com
Reference Manual
00809-0100-4702, Rev AA
Rosemount 702
September 2007
OVERVIEW
Manual This manual is designed to assist in the installation, operation, and
maintenance of Rosemount 702.
Section 1: Overview
• Manual and Transmitter Overview
• Considerations
• Return of Materials
Section 2: Configuration
• Device switch Configuration
• Device Network Configuration
Section 3: Mounting
• Mount the switch
• Switch Assembly/Leads
• Grounding
• LCD Rotation
Section 4: Commissioning
• Network Status
• Verify Operation
Section 5: Operation and Maintenance
• LCD Screen Messages
• LCD Rotation
• Battery Replacement
Appendix A: Specifications and Reference Data
• Specifications
• Dimensional drawings
• Ordering Information
Appendix B: Approvals
• Product Certifications
• Installation Drawings
Transmitter Features of the Rosemount 702 include:
• An installation-ready solution that provides a variety of mounting
options, transmitter configurations, and switches/thermowells
• Flexibility to meet your most demanding applications
• Wireless output with >99% data reliability delivers rich HART data,
protected by industry leading security
• Single or dual switch input with logics for limit contact and opposing
contact applications.
1-2
Reference Manual
00809-0100-4702, Rev AA
September 2007
• The integral LCD conveniently displays the primary switch input and
diagnostics of the transmitter
• Simple and easy installation practices already used today for robust
installations
Rosemount 702
CONSIDERATIONS
General Switches produce either an open or closed signal. With simple HART
configuration the Rosemount 702 converts the switch signal to a
wireless-enabled signal.l.
Commissioning The transmitter can be commissioned before or after installation. It may be
useful to commission it on the bench, before installation, to ensure proper
operation and to become familiar with its functionality. When applicable, make
sure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices. The device will be powered whenever the
battery is installed. To avoid depleting the battery, make sure it is removed
when the device is not in use.
Mechanical Location
When choosing an installation location and position, take into account the
need for access to the transmitter. For best performance, the antenna should
be vertical with some space between objects in a parallel metal plane such as
a pipe or metal framework, as the pipes or framework may adversely affect
the performance of the antenna.
Electrical Battery
The Rosemount 702 Wireless Temperature transmitter is battery powered.
The battery pack with the wireless unit contains 2 “C” size primary
lithium/thionyl chloride batteries. Each battery contains approximately 2.5
grams of lithium, for a total of 5 grams in each pack. Under normal conditions,
the battery materials are self-contained and are not reactive as long as the
batteries and the battery pack are maintained. Care should be taken to
prevent thermal, electrical or mechanical damage. Contacts should be
protected to prevent premature discharge.
Use caution when handling the battery pack. The battery pack may be
damaged if dropped from heights in excess of 20 feet.
Switch
Make switch connections through the cable entry in the side of the connection
head. Be sure to provide adequate clearance for cover removal.
Environmental Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Temperature Effects
The transmitter will operate within specifications for ambient temperatures
between –40 and 185 °F (–40 and 85 °C). Heat from the process is
transferred from the switch to the transmitter housing. If the expected process
temperature is near or beyond specification limits, consider the use of
additional thermowell and extension, or remote mounting the transmitter to
thermally isolate it from the process.
1-3
Rosemount 702
Housing Temperature Rise, Above
Ambient °C (°F)
3 4 5 6 7 8 9
0
60 (108)
50 (90)
40 (72)
30 (54)
20 (36)
10 (18)
4.2
55
Extension Length (in.)
815 °C (1500 °F) Process Temperature
540 °C (1000 °F) Process Temperature
250 °C (482 °F) Process Temperature
Figure 1-1. 702 Transmitter
Connection Head Temperature
Rise vs. Extension Length
Reference Manual
00809-0100-4702, Rev AA
September 2007
Figure 1-1 provides an example of the relationship between transmitter
housing temperature rise and thermowell extension length.
Example
The transmitter specification limit is 85 °C. If the ambient temperature is 55 °C
and the max process temperature to be measured is 815 °C, the maximum
permissible connection head temperature rise is the transmitter specification
limit minus the ambient temperature (moves 85 to 55 °C), or 30 °C.
In this case, an extension of 5” meets this requirement, but 6” provides an
additional margin of thermowell protection, thereby reducing risk of ambient
thermal damage.
Temperature Limits
Operating Limit Storage Limit
With LCD Display –4 to 175 °F
–20 to 80 °C
Without LCD Display –40 to 185 °F
–40 to 85 °C
–40 to 185 °F
–40 to 85 °C
–40 to 185 °F
–40 to 85 °C
1-4
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
RETURN OF MATERIALS To expedite the return process in North America, call the Emerson Process
Management National Response Center toll-free at 800-654-7768. This
center, available 24 hours a day, will assist you with any needed information
or materials.
The center will ask for the following information:
• Product model
• Serial numbers
• The last process material to which the product was exposed
The center will provide
• A Return Material Authorization (RMA) number
• Instructions and procedures that are necessary to return goods that
were exposed to hazardous substances
For other locations outside North America, please contact an Emerson
Process Management sales representative for further instructions.
NOTE
If the device has been exposed to a hazardous substance, a Material Safety
Data Sheet (MSDS) must be included with the returned materials. An MSDS
is required by law to be available to people exposed to specific hazardous
substances.
SHIPPING CONSIDERATIONS FOR WIRELESS PRODUCTS (LITHIUM
BATTERIES):
The unit was shipped to you without the battery installed. Please remove the
battery pack prior to shipping the unit.
Primary lithium batteries (charged or discharged) are regulated in
transportation by the U.S. Department of transportation, and are also covered
by IATA (International Air Transport Association), ICAO (International Civil
Aviation Organization), and ARD (European Ground Transportation of
Dangerous Goods). It is the responsibility of the shipper to ensure compliance
with these or any other local requirements. Please consult current regulations
and requirements before shipping.
1-5
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
1-6
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Section 2 Configuration
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
Device Sensor Configuration . . . . . . . . . . . . . . . . . . . . . . page 2-2
Device Network Configuration . . . . . . . . . . . . . . . . . . . . . page 2-2
Remove Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-5
SAFETY MESSAGES Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Warnings
Failure to follow these installation guidelines could result in death or
serious injury.
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
• Before connecting a 375 Field Communicator in an explosive atmosphere, make
sure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Process leaks could result in death or serious injury.
• Do not remove the thermowell while in operation.
• Install and tighten thermowells and sensors before applying pressure
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
www.rosemount.com
Reference Manual
00809-0100-4702, Rev AA
Rosemount 702
September 2007
Switch Connections The 702 is compatible with a number of simple switches. Figure 2-1 shows
the correct input connections to the switch terminals on the transmitter. To
ensure a proper switch connection, anchor the switch lead wires into the
appropriate compression terminals and tighten the screws.
Switch Leads
If the switch is installed in a high-voltage environment and a fault condition or
installation error occurs, the sensor leads and transmitter terminals could
carry lethal voltages. Use extreme caution when making contact with the
leads and terminals.
Use the following steps to wire the sensor and supply power to the
transmitter:
1. Remove the transmitter enclosure cover (if applicable).
2. Attach the sensor leads according to the wiring diagrams
3. Connect the battery.
4. Verify the connection by observing the LCD
5. Reattach and tighten the cover (if applicable).
DEVICE SENSOR
CONFIGURATION
DEVICE NETWORK
CONFIGURATION
Begin by removing the battery-side housing cover. This will expose the
terminal block and HART communication terminals. Connect the battery to
supply power for configuration.
The Rosemount 702 will receive any HART communications from a handheld
Field Communicator, or AMS. When using a Field Communicator, any
configuration changes must be sent to the transmitter by using the Send key
(F2). AMS configuration changes are implemented when the Apply button is
clicked.
AMS Wireless and Direct Connections
AMS is capable of connecting to devices either directly, using a HART
modem, or through wireless via the 1420. When configuring on the bench
using a HART modem, double click the device icon (or right click and select
Configure/Setup), then choose the Configure/Setup tab. Configure the device
settings using the Direct Connection menu. When configuring wirelessly via
the 1420, double click the device icon (or right click and select
Configure/Setup), then choose the Configure/Setup tab. Configure the device
settings using the Wireless Connection menu.
In order to communicate with the 1420 Wireless Gateway, and ultimately the
Information System, the transmitter must be configured to communicate with
the wireless network. This step is the wireless equivalent of connecting wires
from a transmitter to the information system.
Using a Field Communicator or AMS, enter the Network ID and Join Key so
that they match the Network ID and Join Key of the gateway and other
devices in the network. If the Network ID and Join Key are not identical, the
transmitter will not communicate with the network. The Network ID and Join
Key may be obtained from the 1420 Wireless Gateway on the
Setup>Network>Settings page on the web server.
2-2
Reference Manual
1
2
4
3
00809-0100-4702, Rev AA
September 2007
Figure 2-1. 702 Terminal Block
Rosemount 702
The final device network configuration piece is the Update Rate. This by
default is 5 minutes. This may be changed at commissioning, or at any time
via AMS or the 1420 Wireless Gateway’s web server. The Update Rate
should be between 15 seconds and 60 minutes. For networks of up to 100
wireless devices, fastest Update Rate is 60 seconds. For networks of 50 or
fewer devices, the fastest Update Rate is 15 seconds
When device configuration is completed, remove the battery and replace the
battery cover. Tighten the cover to the proper tension for safety approvals.
To access the Network Settings using a 375 Field Communicator, enter the
following Fast Key Sequence: 1, 3, 3.
Figure 2-2. 375 Field
Communicator Connections
Connect the HART communication leads to the COMM terminals on the
terminal block.
1
2
P/N 00753-9200-0020
3
COMM
4
For HART communication, a 702 DD is required.
2-3
m
n-lin Mn
1. DEVIEET
P 1. PRE VARIABLE
1. TRAN
MITTER VAR
1. Dir In
1
2. PV i
2. PV i
2. Dir In
2
. Nw
r
. PV Diil V
l
.Amin Tm
Infrmi
n 4.l V
l
1. R
i
2. Mmr
.ri
n
2. DIANTI
AND 1. TE
T DEVI
E1.M
r R
4.
nfiri
n
ERVI
E 2. Wri
Pr
2.
.Dir In
.
L
1. L
Dir In
2.lr L
1. Vril Min
1. PV i
2.
V i
.TV i
4.
V i
1. Discr
ete
1 L
ead Resistance
2. Discr
ete
1 Inver
t
1. Discr
ete
In
put Type
1
3
.Discr
ete
1 S/N
2. Di
screte Co
nfiguration1.Di
screte
In
puts
2. Discr
ete
In
put Type
2
2. Am
bient Temp
1. Discr
ete
1 L
ead Resistance
1.Uni
ts
2. Discr
ete
1 Inver
t
3
.Discr
ete
1 S/N
1. P
o
l Addr
2. N
u
m Req Pream
s
3
. DEVICEOUTPUT 1. HARTOUTPUT
CO
NFIGURATION2.L
CDOutput
1. LCD M
ode
3.CO
NFIGURATION
1.
ag
2. D
ate
3.Descripto
r
4. M
essage
5.Model6.Mode
l Number I 1.Universal Rev
7. M
ode
l Number II 2. Field Dev Rev
4. DEVI
CE8.Mode
l Number III
3.Software Re
v
INF
O
RMATION1.N
etwork9
. Write Pr
otect
4. Hardware Rev
2. Fi
eld Device
Inf
o
10.Revision Number
s
3
.Discr
ete
In
put
11.Transmi
tterS/
N
Inf
ormatio
n 12. Dev ID
1
3
.Distri
buto
r
1. R
adio Mode
l Number
2. R
adio Type
3
. Wirel
ess Device Type
1. Discr
ete
In
put Type
14.
Get Unique
ID
2. Di
screte
In
put Type
2
5.RadioS
W M
ajo
r Rev
5
. MEASUREMENT
6.RadioS
W Minor Rev
FILTERIN
G
1.
50/60
Hz Filter7.R
adioS
W Buil
d
8.Radio
HW Rev
4. NETW
O
RK 1.Smart Power1.P
owe
r M
ode
2. Network ID 2.Transmit R
ate
3.Set Jo
in K
ey
3.Database Mode
l
4. R
adio State
4. High Power Refresh
1. R
adio Mode
l Number
2. R
i
T
. Wirl Dvi T
4.
ni
ID
.RiW M
r R
v
.RiW Min
r R
v
. REVIEW 1. Nwrk 7. RiW B
il
2. Rvii
n Nmr
1.
nivrl R
v
.Ri HW R
v
.Dvi Vril Rvi
w2.Fi
l Dvi Rv
.Pwr M
4. D
v
Rviw
.fwr R
v1
.Trnmi
R
.Dvi Infrmi
n4.H
rwr Rv 11. D
M
.Mrmn Fil
rin
1.
ni
1. Dir In
T
2. L
L2.Di
r
In
1
N
1. Wri
Pr
.
L
.Dir In
1 L Ri
n
2. Dvi ID 1. Dir In Rv4.Di
r
In
1 In
r
.TrnmirN2.Am
in T Rv
.Dir In
2
N
4. T
.l Vl R
v1.
ni
.Dir In
1 L Ri
n
.D
2. L
L7.Di
r
In
2 In
r
.Drir
.
L
7. M
.M
l 1. Primr Vril
1. PV i
.Dirir 2. HART
1.Ml
.L
D M
1. P
llin Ar
11. D
v Fl
2. N
m R
Prml
12. M
l Nmr I 1.
Hz Fil
r
.Philin
lin
1.Ml Nmr II
14. M
l Nmr III
Reference Manual
00809-0100-4702, Rev AA
Rosemount 702
September 2007
HART Menu Tree For ease of operation, changing setup, such as switch type, can be completed
in several locations.
Figure 2-3. Field Communicator Menu Tree
2-4
T
Reference Manual
00809-0100-4702, Rev AA
Rosemount 702
September 2007
Fast Key Sequence Table 2-1 lists the fast key sequences for common transmitter functions.
NOTE:
The fast key sequences assume that DD Dev v1, DD v4 is being used.
Table 2-1. 702 Fast Key
Sequence
Calibration
REMOVE BATTERY
Function Key Sequence Menu Items
Device Information 1, 3, 4, 2 Tag, Date, Descriptor, Message, Model, Model Number I,
Wireless 1, 4 Smart Power, Network ID, Set Join Key, Radio State
Discrete Input Configuration 1, 3, 2, 1 Output configuration, Discrete Input Configuration
II, III, Write Protect, Revision Numbers, Transmitter Serial
Numbers, Device ID
After the sensor and network have been configured, remove the battery pack
and replace the transmitter cover. The battery pack should be inserted only
when the device is ready to be commissioned.
2-5
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
2-6
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Section 3 Mounting
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-2
Direct Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-2
Remote Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-3
LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-4
Ground the Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-5
SAFETY MESSAGES Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Warnings
Failure to follow these installation guidelines could result in death or
serious injury.
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
• Before connecting a 375 Field Communicator in an explosive atmosphere, make
sure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Process leaks could result in death or serious injury.
• Do not remove the thermowell while in operation.
• Install and tighten thermowells and switches before applying pressure
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired operation.
This device must be installed to ensure a minimum antenna separation distance of 20 cm
from all persons..
www.rosemount.com
Reference Manual
Housing Temperature Rise, Above
Ambient °C (°F)
3 4 5 6 7 8 9
0
60 (108)
50 (90)
40 (72)
30 (54)
20 (36)
10 (18)
4.2
55
Extension Length (in.)
815 °C (1500 °F) Process Temperature
540 °C (1000 °F) Process Temperature
250 °C (482 °F) Process Temperature
00809-0100-4702, Rev AA
Rosemount 702
September 2007
MOUNTING The Rosemount 702 can be installed in one of two configurations: Direct
Mount, where the switch is connected directly to the 702 housing’s conduit
entry, or Remote Mount, where the switch is mounted separate from the 702
housing, then connected to the 702 via conduit. Choose the installation
sequence that corresponds to the mounting configuration.
Figure 3-1 provides an example of the relationship between transmitter
housing temperature rise and extension length.
Figure 3-1. 702 Transmitter
Connection Head Temperature
Rise vs. Extension Length
Example
The transmitter specification limit is 85 °C. If the ambient temperature is 55 °C
and the max process temperature to be measured is 815 °C, the maximum
permissible connection head temperature rise is the transmitter specification
limit minus the ambient temperature (moves 85 to 55 °C), or 30 °C.
In this case, an extension of 5” meets this requirement, but 6” provides an
additional margin of thermowell protection, thereby reducing risk of ambient
thermal damage.
Direct Mount The direct mount installation should not be used when installing with a
Swagelok
®
fitting.
1. Install the switch according to standard installation practices. Be sure
to use thread sealant on all connections.
2. Attach the 702 housing to the switch using the threaded conduit entry.
3. Attach the switch wiring to the terminals as indicated on the wiring
NOTE
Use caution when handling the battery pack. The battery pack may be
damaged if dropped from heights in excess of 20 feet.
diagram.
4. Connect the battery pack if commissioning the device.
3-2
Reference Manual
Possible antenna rotation shown.
Antenna rotation allows for best
installation practices in any
configuration.
00809-0100-4702, Rev AA
September 2007
Rosemount 702
NOTE:
Wireless devices should be powered up after the 1420 Wireless Gateway and
in order of proximity from the 1420, beginning with the closest device to the
1420. This will result in a simpler and faster network installation.
5. Close the housing cover and tighten to safety specification. Always
ensure a proper seal by installing the electronics housing covers so
that metal touches metal, but do not over tighten.
6. Position the antenna such that it is vertical, typically straight up
(antenna may be pointed straight down as well).
Remote Mount 1. Install the switch/thermocouple according to standard installation
practices. Be sure to use thread sealant on all connections.
2. Run wiring (and conduit if necessary) from the switch/thermocouple
to the 702.
3. Pull the wiring through the threaded conduit entry of the 702.
4. Attach the switch/thermocouple wiring to the terminals as indicated
on the wiring diagram.
5. Connect the battery pack if commissioning.
NOTE
Use caution when handling the battery pack. The battery pack may be
damaged if dropped from heights in excess of 20 feet.
3-3
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
NOTE:
Wireless devices should be powered up after the 1420 Wireless Gateway and
in order of proximity from the 1420, beginning with the closest device to the
1420. This will result in a simpler and faster network installation.
6. Close the housing cover and tighten to safety specification. Always
ensure a proper seal by installing the electronics housing covers so
that metal touches metal, but do not over tighten.
7. Position the antenna such that it is vertical, typically straight up
(antenna may be pointed straight down as well).
LCD Display Transmitters ordered with the LCD display will be shipped with the display
installed.
The optional LCD display can be rotated in 90-degree increments by
squeezing the two tabs, pulling out, rotating and snapping back into place.
If LCD pins are inadvertently removed from the interface board, carefully
re-insert the pins before snapping the LCD display back into place.
Use the following procedure and Figure 3-2 to install the LCD display:
1. Remove the LCD cover. Do not remove the instrument covers in
explosive environments when the circuit is live.
2. Put the four-pin connector into the LCD display, rotate to the desired
position and snap into place.
Note the following LCD temperature limits:
3-4
Reference Manual
LCD Display
LCD
Cover
LCD
Pins
switch Wires
Shield ground point
Transmitter
00809-0100-4702, Rev AA
September 2007
Figure 3-2. Optional LCD
Display
Rosemount 702
Operating:–4 to 175 °F (–20 to 80 °C)
Storage:–40 to 185 °F (–40 to 85 °C)
3. Replace the transmitter cover.
NOTE
Only use Rosemount Wireless LCD Part Number: 00753-9004-0002.
Ground the Transmitter The transmitter will operate with the housing either floating or grounded.
However, the extra noise in floating systems affects many types of readout
devices. If the signal appears noisy or erratic, grounding the transmitter at a
single point may solve the problem.
The electronics enclosure should be grounded in accordance with local and
national installation codes. This can be accomplished via the process
connection, via the internal case grounding terminal, or via the external
grounding terminal.
Switch Inputs
Each process installation has different requirements for grounding. Use the
grounding options recommended by the facility for the specific switch type, or
begin with grounding Option 1 (the most common).
Option 1:
1. Connect switch wiring shield to the transmitter housing (only if the
housing is grounded).
2. Ensure the transmitter housing is electrically isolated from the switch
wiring.
3-5
Rosemount 702
switch Wires
Shield ground point
Transmitter
Reference Manual
00809-0100-4702, Rev AA
September 2007
Option 2:
1. Ground switch wiring shield at the switch.
2. Ensure that the switch wiring and shield is electrically isolated from
the transmitter housing.
NOTE:
Always use facility recommended wiring practices.
3-6
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Section 4 Commissioning
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-1
Verify Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-2
SAFETY MESSAGES Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Warnings
Failure to follow these installation guidelines could result in death or
serious injury.
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
• Before connecting a 375 Field Communicator in an explosive atmosphere, make
sure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Process leaks could result in death or serious injury.
• Do not remove the thermowell while in operation.
• Install and tighten thermowells and switches before applying pressure
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
www.rosemount.com
NOTE
The Rosemount 702 and all other wireless devices should be installed only
after the 1420 Wireless Gateway has been installed and is functioning
properly.
Wireless devices should also be powered up in order of proximity from the
1420 Wireless Gateway, beginning with the closest device to the 1420. This
will result in a simpler and faster network installation.
Reference Manual
n e t w k
13 0 5
I D
n e t w k
2 p a r n t
S u p l y
7. 2 1
v o l t s
n e t w k
1 p a r n t
n e t w k
2 p a r n t
00809-0100-4702, Rev AA
Rosemount 702
September 2007
VERIFY OPERATION Operation can be verified in three locations, at the device via the Local
Display, using the 375 Field Communicator, or at the Gateway via the 1420
Wireless Gateway’s integrated web server.
Local Display
During normal operation, the LCD will display the PV value at the wireless
transmit rate up to as fast as 1 minute intervals. Refer to LCD Screen
Messages on page 5-2 for error codes and other LCD messages. Press the
Diagnostic button to display the TAG, Device ID, Network ID, Network Join
Status and Device Status screens. For Device Status screens, see LCD
Screen Messages on page 5-2
Figure 4-1. Diagnostic Screen Sequence
Tag Device ID Network ID Network Status Device Variables
A b c d e
f g h
i d - X X
X X X X X X
Figure 4-2. Network Status Screens
Searching for
Network
n e t w k
a - s r c h
Joining Network Connected with
1Parent
n e t w k
j o i n g
Connected with
2 Parents
375 Field Communicator
To verify device operation using a HART Field Communicator, a 702 DD is
required.
Function Key Sequence Menu Items
Network 1, 4 Smart Power, Network ID, Set Join
Key, Radio State
1420 Wireless Gateway
To verify device operation using the 1420 Wireless Gateway’s integrated web
server, navigate to the Explorer>Status page. This page will show whether
the device has joined the network and if it is communicating properly.
4-2
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
If the Rosemount 702 was configured with the Network ID and Join Key and
sufficient time for network polling has passed, the transmitter will be
connected to the network. To verify connectivity, open the 1420 Wireless
Gateway’s integral web interface and navigate to the Explorer>Status page.
This page will display the transmitter’s tag, PV, SV, TV, QV, Last Update,
Update Rate, Battery Voltage, and Status. A green status indicator means that
the device is working properly. A red indicator means that there is a problem
with either the device or its communication path. For more detail on a specific
device, click on the tag name.
Troubleshooting
The most common cause of incorrect operation is the Network ID and Join
Key. The Network ID and Join Key in the device must match that of the 1420
Wireless Gateway. The Network ID and Join Key may be obtained from the
1420 Wireless Gateway on the Setup>Network>Settings page on the web
server.
4-3
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
4-4
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Section 5 Operation and Maintenance
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-1
LCD Screen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-2
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-9
SAFETY MESSAGES Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Warnings
Failure to follow these installation guidelines could result in death or
serious injury.
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
• Before connecting a 375 Field Communicator in an explosive atmosphere, make
sure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Process leaks could result in death or serious injury.
• Do not remove the thermowell while in operation.
• Install and tighten thermowells and switches before applying pressure
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
www.rosemount.com
Rosemount 702
LCD SCREEN
MESSAGES
Reference Manual
00809-0100-4702, Rev AA
September 2007
Startup Screen
Sequence
The following screens will display when the battery is first connected to the
Rosemount 702.
X X X X X
X X X X x x x
x x x x x x
702
W I r e l s
All Segments On: used to visually determine if
there are any bad segments on the LCD
Device Identification: used to determine Device
Type.
A b c d e
f g h
s n s r1
True
Device Information - Tag: user entered tag which
is 8 characters long - will not display if all characters
are blank
PV Screen - Discrete input 1 or logic output value
depending on how the device is configured
5-2
Reference Manual
S N S R 2
True
S u p l y
7. 2 1
v o l t s
00809-0100-4702, Rev AA
September 2007
Rosemount 702
SV Screen - Discrete input 2
D E V
2 5. 2 5
d e g c
a l e r t
p r e s n t
TV Screen - feature board temperature value
QV Screen - voltage reading at the power supply
terminals
Alert Screen - at least one alert is present - this
screen will not display if no alerts are present
Diagnostic Button
Screen Sequence
The following five screens will display when the device is operating properly
and the Diagnostic Button has been pressed.
A b c d e
f g h
Device Information - Tag: user entered tag which
is 8 characters long - will not display if all characters
are blank
5-3
Rosemount 702
n e t w k
u n k n w n
Reference Manual
00809-0100-4702, Rev AA
September 2007
i d - X X
X X X X X X
n e t w k
13 0 5
I D
n e t w k
2 p a r n t
Device Identification: used to determine Device ID
Diagnostic Button Screen 3: assuming the device
has the correct join key, this ID tells the user what
network the device can connect with
Diagnostic Button Screen 4.11: the device has
joined a network and has been fully configured and
has multiple parents
Network Diagnostic
Status Screens
5-4
S u p l y
Diagnostic Button Screen 5: voltage reading at
the power supply terminals
7. 2 1
v o l t s
These screens display the network status of the device. Only one will be
shown during the startup sequence or diagnostic sequence.
Diagnostic Button Screen 4.1: the device has yet
to retrieve the information from the 1420 and is still
in the process of being activated
Reference Manual
n e t w k
a - s r c h
n e t w k
s l e e p
00809-0100-4702, Rev AA
September 2007
n e t w k
a c t i v e
n e t w k
j o i n g
Rosemount 702
Diagnostic Button Screen 4.2: the device has
received the ACTIVATE command from the 1420,
but is in the process of being configured to the
wireless network
Diagnostic Button Screen 4.3: the device has
sent JOIN request and is waiting for the ACTIVATE
command
n e t w k
p - s r c h
Diagnostic Button Screen 4.4: the device is in
active search
Diagnostic Button Screen 4.5: the device is in
passive search
Diagnostic Button Screen 4.6: the device
couldn’t find the network and is in deep sleep
mode to preserve battery power
5-5
Rosemount 702
n e t w k
r e s e t
Reference Manual
00809-0100-4702, Rev AA
September 2007
n e t w k
s y n c
n e t w k
b c k o f f
Diagnostic Button Screen 4.7: the device
synchronized to a network
Diagnostic Button Screen 4.8: the device will
reset
Diagnostic Button Screen 4.9: the device
couldn’t join because of dropped packets and will
reset
Device Diagnostic
Screens
5-6
Diagnostic Button Screen 4.10: the device has
n e t w k
1 p a r n t
The following screens will show the device diagnostics depending on the state
of the device.
D E V
f A i l u r
joined a network and has been fully configured but
has only 1 parent device
Device Information - Status: there is a critical error
which may prevent the device from operating
correctly. Check additional status screens for more
information.
Reference Manual
S N S R 2
True
00809-0100-4702, Rev AA
September 2007
Rosemount 702
s n s r1
True
D E V
2 5. 2 5
d e g c
PV Screen - Discrete input 1 or logic output value
depending on how the device is configured
SV Screen - Discrete input 2
TV Screen - feature board temperature value
S u p l y
7. 2 1
v o l t s
a l e r t
p r e s n t
QV Screen - voltage reading at the power supply
terminals
Alert Screen - at least one alert is present - this
screen will not display if no alerts are present
5-7
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
A b c d e
f g h
i d - 1 2
3 4 5 6 7 8
s u p l y
f a i l u r
Diagnostic Button Screen 1 - Tag: user entered
tag which is 8 characters long - will not display if all
characters are blank
Diagnostic Button Screen 2: the device’s identifier
that is used to make up the HART long address - the
1420 Wireless Gateway may use this to help identify
devices if no unique user tag is available
Diagnostic Button Screen 7.1: the terminal
voltage has dropped below level of operating limit.
Replace the battery
(Part Number: 00753-9220-XXXX)
5-8
s u p l y
l o w
r a d i o
f a i l u r
Diagnostic Button Screen 7.2: the terminal
voltage is below the recommended operating range
- if this is a battery operated device, the battery
should be replaced - for line powered devices, the
supply voltage should be increased
Diagnostic Button Screen 8: the device cannot
retrieve information from the radio in the device - the
device may still be operational and publishing HART
data
Reference Manual
c o n f g
w a r n
00809-0100-4702, Rev AA
September 2007
c o n f g
f a i l u r
Rosemount 702
Diagnostic Button Screen 9.1: configuration of the
transmitter is invalid such that critical operation of
the device may be affected - check the extended
configuration status to identify which configuration
item(s) need to be corrected
Diagnostic Button Screen 9.2: configuration of the
transmitter is invalid such that non-critical operation
of the device may be affected - check the extended
configuration status to identify which configuration
item(s) need to be corrected
BATTERY
REPLACEMENT
Diagnostic Button Screen 10.1: a switch attached
to the transmitter has failed, and valid readings from
s n s r
f a i l u r
NOTE
Use the Rosemount Wireless LCD Part Number: 00753-9004-0002.
Expected battery life is eight years at reference conditions.
When battery replacement is required, remove the battery cover and remove
the battery pack. Replace the pack (part number 00753-9220-XXXX) and
replace the cover. Tighten to specification and verify operation.
Handling Considerations
The battery pack with the wireless unit contains 2 “C” size primary
lithium/thionyl chloride batteries. Each battery contains approximately 2.5
grams of lithium, for a total of 5 grams in each pack. Under normal conditions,
the battery materials are self-contained and are not reactive as long as the
batteries and the battery pack integrity are maintained. Care should be taken
to prevent thermal, electrical or mechanical damage. Contacts should be
protected to prevent premature discharge.
that switch are no longer possible - check the switch
and switch wiring connections - check additional
status for more detailed information of the failure
source
(1)
(1) Reference conditions are 70° F (21° C), transmit rate of once per minute, and routing data
for three additional network devices.
5-9
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
Use caution when handling the battery pack. The battery pack may be
damaged if dropped from heights in excess of 20 feet.
Battery hazards remain when cells are discharged.
Environmental Considerations
As with any battery, local environmental rules and regulations should be
consulted for proper management of spent batteries. If no specific
requirements exist, recycling through a qualified recycler is encouraged.
Consult the materials safety data sheet for battery specific information.
Shipping Considerations
The unit is shipped to you without the battery installed. Unless specifically
instructed to do otherwise, remover the battery pack from the unit prior to
shipping.
Primary lithium batteries are regulated in transportation by the U.S.
Department of Transportation, and are also covered by International Air
Transport Association (IATA), International Civil Aviation Organization (ICAO),
and European Ground Transportation of Dangerous Goods (ARD). It is the
responsibility of the shipper to ensure compliance with these or any other
local requirements. Please consult current regulations and requirements
before shipping.
5-10
Reference Manual
00809-0100-4702, Rev AA
September 2007
Appendix A Specifications and
Reference Data
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-1
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-3
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-4
SPECIFICATIONS
Rosemount 702
Functional
Specifications
Input
Supports Dry Switch input types. Does not support NAMUR type switches.
Output
Wireless enabled, single or dual switch states or limit or opposing contact
output.
Local Display
The optional five-digit integral LCD Display can display switch status or logic
output. Display updates at transmit rate up to once per minute.
Humidity Limits
0–100% relative humidity
Transmit Rate
User selectable, 15 sec. to 60 min.
Switch Pole Rate
User selectable, 15 sec. to 60 min. same as transmit rate.
Physical Specifications Electrical Connections / Battery
• Replaceable, non-rechargeable, Intrinsically Safe Lithium-Thionyl
Chloride battery pack with PBT enclosure.
• Eight year battery life at reference conditions.
• 4 Screw Terminals for switch connection.
(1)
www.rosemount.com
Field Communicator Connections
Communication Terminals
Clips permanently fixed to terminal block
Materials of Construction
Enclosure
(1) Reference conditions are 70° F (21° C), transmit rate of once per minute, and routing data
for three additional network devices.
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
Housing
• Low-copper aluminum
Paint
• Polyurethane
Cover O-ring
• Buna-N
Terminal Block and Battery Pack
•PBT
Antenna
• PBT/PC integrated omnidirectional antenna
Mounting
Transmitters may be attached directly to the switch. Mounting brackets also
permit remote mounting. See “Dimensional Drawings” on page A-3.
Weight
702 without LCD - 4.6 lbs. (2 kg)
702 with M5 LCD - 4.7 lbs (2.1 kg)
Performance
Specifications
Enclosure Ratings (702)
Housing option code D is NEMA 4X, and IP66.
EMC (ElectroMagnetic Compatibility)
The 702 meets all requirements listed under IEC 61326.
Self Calibration
The analog-to-digital measurement circuitry automatically self-calibrates for
each switch status update by comparing the dynamic measurement
to extremely stable and accurate internal reference elements.
Vibration Effect
Tested per the requirements of IEC60770-1 field or pipeline with high vibration
level (10-60 Hz 0.21 mm displacement peak amplitude / 60-2000 Hz 3g).
A-2
Reference Manual
Possible antenna rotation shown.
900 mHz ANTENNA
2.4 GHz ANTENNA
3.457
(87.8)
00809-0100-4702, Rev AA
September 2007
DIMENSIONAL DRAWINGS
Rosemount 702
702 Direct Mount
Dimensions are in inches (millimeters)
A-3
Rosemount 702
ORDERING INFORMATION
Model Product Description
702 DiscreteTransmitter
Code Transmitter Type
D Wireless Field Mount
Code Output
X Wireless
Code Measurement
22 Dual Input
Code Housing Metal
D Dual Compartment Housing - Aluminum AL
Code Conduit Threads
1 1/2 - 14 NPT
Code Certifications
I5 FM Intrinsically Safe, Non-incendive
I6 CSA Intrinsically Safe
I1 ATEX Intrinsically Safe
I7 IECEx Intrinsically Safe
NA No Approval
Code Wireless Options
Wireless Transmitter Rate
WA User Configurable Transmit Rate
Operating Frequency and Protocol
1 2.4 GHz DSSS, HART
2 900MHz FHSS, HART
Antenna
WK Integral, Omnidirectional Antenna Long-life
SmartPower™
1 Intrinsically Safe Battery Pack
Note: Battery must be shipped separately, order Part #00753-9220-0001
Meter
M5 LCD Meter
Mounting Bracket
B4 Universal L mounting bracket for 2-inch pipe mounting - SST bracket and bolts
Configuration
C1 Factory Configure Date, Descriptor, Message Fields, and Wireless Parameters
Cable Gland
G2 Cable gland (7.5 mm - 11.9 mm)
G4 Thin Wire Cable Gland (3 mm - 8 mm)
Typical Model Number: 702 D X 22 D 1 NA WA1 WK1 M5
Reference Manual
00809-0100-4702, Rev AA
September 2007
A-4
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Appendix B Product Certifications
Approved Manufacturing Locations . . . . . . . . . . . . . . . . . page B-1
Telecommunication Compliance . . . . . . . . . . . . . . . . . . . . page B-1
FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B-1
European Directive Information . . . . . . . . . . . . . . . . . . . . page B-1
Ordinary Location Certification for FM . . . . . . . . . . . . . . . page B-1
Hazardous Locations Certificates . . . . . . . . . . . . . . . . . . . page B-2
Approved Manufacturing
Locations
Telecommunication
Compliance
Rosemount Inc. – Chanhassen, Minnesota, USA
Emerson Process Management GmbH & Co. - Karlstein, Germany
Emerson Process Management Asia Pacific Private Limited - Singapore
All wireless devices require certification to ensure that they adhere to
regulations regarding the use of the RF spectrum. Nearly every country
requires this type of product certification. Emerson is working with
governmental agencies around the world to supply fully compliant products
and remove the risk of violating country directives or laws governing wireless
device usage. To see which countries our devices have received certification
for use in, see www.rosemount.com/smartwireless.
FCC and IC This device complies with Part 15 of the FCC Rules. Operation is subject to
the following conditions: This device may not cause harmful interference. This
device must accept any interference received, including interference that may
cause undesired operation.
This device must be installed to ensure a minimum antenna separation
distance of 20 cm from all persons.
European Directive
Information
The EC declaration of conformity for all applicable European directives for this
product can be found at www.rosemount.com. A hard copy may be obtained
by contacting an Emerson Process Management representative.
ATEX Directive (94/9/EC)
Emerson Process Management complies with the ATEX Directive.
Electro Magnetic Compatibility (EMC) (2004/108/EC)
EN 61326-1 1997, Amendments A1, A2, and A3
Radio and Telecommunications Terminal Equipment Directive (R&TTE)
(1999/5/EC)
Emerson Process Management complies with the R&TTE Directive.
Ordinary Location
Certification for FM
www.rosemount.com
As standard, the transmitter has been examined and tested to determine that
the design meets basic electrical, mechanical, and fire protection
requirements by FM, a nationally recognized testing laboratory (NRTL) as
accredited by the Federal Occupational Safety and Health Administration
(OSHA).
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
Hazardous Locations
Certificates
North American Certifications
Factory Mutual (FM) Approvals
I5 FM Intrinsic Safety and Non-incendive
Intrinsically Safe for Class I/II/III, Division 1, Groups A, B, C, D, E, F, and G.
Zone Marking: Class I, Zone 0, AEx ia llC
Temperature Codes T4 (T
T5 (T
Non-incendive for Class I, Division 2, Groups A, B, C, and D.
Dust Ignition proof for Class II/III, Division 1, Groups E, F, and G
Ambient temperature limits: -50 to 85 °C
Intrinsically Safe and non-incendive when installed in accordance with
Rosemount drawing 00702-1000.
For use with Rosemount battery pack P/N 753-9220-XXXX only.
Enclosure Type 4X / IP66
CSA - Canadian Standards Association
I6 CSA Intrinsic Safety
Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D.
Temp Code T3C
Enclosure Type 4X / IP66
For use with Rosemount battery pack P/N 753-9220-XXXX only.
Intrinsically Safe when installed per Rosemount drawing 00702-1020
= -50 to 70° C)
amb
= -50 to 40° C)
amb
Table B-1. Switch Parameters
European Certifications
I1 ATEX Intrinsic Safety
Certificate No.: See Certificate II 1G
Ex ia IIC T5 (T
Ex ia IIC T4 (T
For use with Rosemount battery pack P/N 753-9220-XXXX only
IP66
1180
Sensor
Uo = 6.6 V
Io = 3.6 mA
Po = 23.3 mW
Co = 11 uF
Lo = 500 mH
= -50 °C to 40 °C)
a
= -50 °C to 70 °C)
a
B-2
Reference Manual
Radio Power Label
00809-0100-4702, Rev AA
September 2007
Table B-2. Switch Parameters
Rosemount 702
IECEx Certifications
I7 IECEx Intrinsic Safety
Certificate No.: See Certificate
Ex ia IIC T5 (T
Ex ia IIC T4 (T
IP66
For use with Rosemount battery pack P/N 753-9220-XXXX only
1180
Sensor
Uo = 6.6 V
Io = 3.6 mA
Po = 23.3 mW
Co = 11 uF
Lo = 500 mH
= -50 °C to 40 °C)
amb
= -50 °C to 70 °C)
amb
Table B-3.
Country Restriction
Bulgaria General authorization required for outdoor use and public service
France Outdoor use limited to 10mW e.i.r.p.
Italy If used outside of own premises, general authorization is required.
Norway May be restricted in the geographical area within a radius of 20 km
Romania Use on a secondary basis. Individual license required.
.
Radio Power Label - see Figure B-1 - indicates output power configuration of
the radio. Devices with this label are configured for output power less than 10
mW e.i.r.p. At time of purchase the customer must specify ultimate country of
installation and operation
Figure B-1. Radio Power Label Positioning
from the center of Ny-Alesund.
B-3
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702 FM Intrinsically Safe Installation Drawing
B-4
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
Rosemount 702 CSA Intrinsic Safety Installation Drawing
B-5
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
B-6
Reference Manual
00809-0100-4702, Rev AA
September 2007
Rosemount 702
B-7
Rosemount 702
Reference Manual
00809-0100-4702, Rev AA
September 2007
B-8
Reference Manual
00809-0100-4702, Rev AA
September 2007
The Emerson logo is a trade mark and service mark of Emerson Electric Co.
Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc.
PlantWeb is a registered trademark of one of the Emerson Process Management group of companies.
HART is a registered trademark of the HART Communication Foundation.
Lexan and Noryl are registered trademark of General Electric.
All other marks are the property of their respective owners.
Standard Terms and Conditions of Sale can be found at www.rosemount.com\terms_of_sale
Emerson Process Management
Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN 55317 USA
T (U.S.) 1-800-999-9307
T (International) (952) 906-8888
F (952) 949-7001
www.rosemount.com
Emerson Process Management
Heath Place
Bognor Regis
West Sussex PO22 9SH
England
T 44 (1243) 863 121
F 44 (1243) 867 554
Emerson Process Management Asia
Pacific Private Limited
1 Pandan Crescent
Singapore 128461
T (65) 6777 8211
F (65) 6777 0947
AP.RMT-Specialist@emersonprocess.com
¢00809-0100-4728g¤
© 2007 Rosemount Inc. All rights reserved.
Loading...