Rosemount 2088, 2090P, and 2090F Pressure Transmitters with 4–20 mA HART and 1–5 Vdc HART Low Power Protocol Quick Start Guide

Quick Start Guide

00825-0100-4690, Rev GD

February 2019

Rosemount™ 2088, 2090P, and 2090F
Pressure Transmitters

with 4–20 mA HART® and 1–5 Vdc HART
Low Power Protocol

Quick Start Guide February 2019

Contents

Mount the transmitter................................... 3

Set the jumpers..............................................7

Connect the wiring and power....................... 9

Verify configuration..................................... 12

Trim the transmitter.................................... 14

Safety instrumented systems.......................16

Product Certifications.................................. 19

Rosemount 2088 and 2090 Declaration of

Conformity.................................................. 40

2 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

1 Mount the transmitter

1.1 Rosemount™ 2088

Mount directly to the impulse line without using an additional mounting
bracket or mount directly to a wall, panel, or two-inch pipe using an optional
mounting bracket.

1.2 Rosemount™ 2090P

Mount directly to the process pipe using an existing weld spud, or have a
skilled welder install a new weld spud using a TIG welder. Refer to Reference

Manual for complete welding instructions. Improper installation may result in

weld spud distortion. Recommended mounting in upright or horizontal
position to allow proper draining of vent.

1.3 Rosemount™ 2090F

Mount directly to the process pipe using a standard sanitary fitting (either a

1.5- or 2-in. Tri Clamp connection). Recommended mounting in upright or
horizontal position to allow proper draining of vent.

Figure 1-1: Transmitter Direct Mounting

Do not apply torque directly to the electronics housing. To avoid damage,
apply torque only to the hex-shaped process connection.

Rosemount
2088

A. ½–14 NPT female process connection
B. Vessel wall
C. Weld spud

D. O-ring

E. 1½- or 2-in. Tri Clamp connection

Quick Start Guide 3

Rosemount 2090P Rosemount

2090F

Quick Start Guide February 2019

Figure 1-2: Panel and Pipe Mounting

Panel mount Pipe mount

1.4 Liquid flow applications

Transmitter mounting procedure for liquid flow applications.

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

Example

1.5 Gas flow applications

Transmitter mounting procedure for gas flow applications.

Procedure

1. Place taps in the top or side of the line.

2. Mount level or above the taps.

4 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

Example

1.6 Steam flow applications

Transmitter mounting procedure for steam flow applications.

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Example

1.7

Quick Start Guide 5

Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to
provide a water/dust tight conduit seal and meets requirements of NEMA
Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are
required. For M20 threads, install conduit plugs to full thread engagement or
until mechanical resistance is met.

®

A

Quick Start Guide February 2019

1.8 Gage transmitter orientation

The low side pressure port (atmospheric reference) on the gage transmitters
with aluminum housings are located in the neck of the transmitter, behind the
housing. The vent path is 360° around the transmitter between the housing
and sensor. (See Figure 1-3.)

Keep the vent path free of any obstruction, including but not limited to paint,
dust, and lubrication by mounting the transmitter so that the process can
drain away.

Figure 1-3: Gage Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

6 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

2 Set the jumpers

If alarm and security jumpers are not installed, the transmitter will operate
normally with the default alarm condition alarm high and the security off.

Procedure

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side. Do not
remove the instrument cover in explosive atmospheres when the
circuit is live.

3. Ensure full contact with terminal block screw and washer. When using
a direct wiring method, wrap wire clockwise to ensure it is in place
when tightening the terminal block screw.

Note

The use of a pin or a ferrule wire terminal is not recommended as the
connection may be more susceptible to loosening over time or under
vibration.

4. Reposition the jumper. Avoid contact with the leads and the terminals.
See Figure 2-1 for the location of the jumper and the ON and OFF
positions.

5. Reattach the transmitter cover. The cover must be fully engaged to
comply with explosion-proof requirements.

Example

Figure 2-1: Rosemount 2088 Transmitter Electronics Board

Without LCD display

Low power without LCD display Low power with LCD display

Quick Start Guide 7

With LCD display

Quick Start Guide February 2019

A. Alarm
B. Security

8 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

3 Connect the wiring and power

Use the following steps to wire the transmitter:

Procedure

1. Remove the housing cover on the side marked field terminals.

2. Connect the positive lead to the “PWR/COMM+” terminal, and the
negative lead to the “–” terminal.

3. Ensure proper grounding. It is important that the instrument cable
shield:

• Be trimmed close and insulated from touching the transmitter

housing

• Be connected to the next shield if cable is routed through a

junction box

• Be connected to a good earth ground at the power supply end

Note

Installation of the transient protection terminal block does not provide
transient protection unless the Rosemount 2088 case is properly
grounded.

Note

Do not connect the powered signal wiring to the test terminals. Power
could damage the test diode in the test connection. Twisted pair cable
yields best results. For high EMI/RFI environments, shielded twisted
pair cable should be used. Use 24 AWG or larger wire and do not
exceed 5,000 ft. (1,500 m).

4. Plug and seal unused conduit connections.

5. If applicable, install wiring with a drip loop. Arrange the drip loop
so the bottom is lower than the conduit connections and the
transmitter housing.

6. Replace the housing cover.

Figure 3-1 and Figure 3-2 show wiring connections necessary to power

a Rosemount 2088 Transmitter and enable communications with a
hand-held Field Communicator:

Quick Start Guide 9

Quick Start Guide February 2019

Example

Figure 3-1: Bench Hook-up Wiring Diagrams (4–20 mA Transmitters)

A. RL ≥ 250Ω
B. 24 Vdc supply
C. Current meter

Figure 3-2: Field Wiring for Rosemount 2088 — Low Power Option Code N

A. Voltmeter
B. Power supply

3.1

10 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

Power supply

The dc power supply (Option S: 10.5–42.4 V and Option N: 6–14 V) should
provide power with less than two percent ripple. The total resistance load is
the sum of the resistance of the signal leads and the load resistance of the
controller, indicator, and related pieces. The resistance of intrinsic safety
barriers, if used, must be included.

February 2019 Quick Start Guide

Figure 3-3: Maximum Loop Resistance = 43.5 × (Power Supply Voltage –

10.5)

The Field Communicator requires a minimum loop resistance of 250Ω for
communication.

Quick Start Guide 11

Quick Start Guide February 2019

4 Verify configuration

A check (✓) indicates the basic configuration parameters. At minimum, these
parameters should be verified as part of the configuration and startup
procedure.

Function HART Fast Key sequence

Analog Output Alarm 1, 4, 3, 2, 4

Burst Mode Control 1, 4, 3, 3, 3

Burst Option 1, 4, 3, 3, 4

Calibration 1, 2, 3

✓ Damping 1, 3, 5

Date 1, 3, 4, 1

Descriptor 1, 3, 4, 2

Digital To Analog Trim (4–20 mA Output) 1, 2, 3, 2, 1

Disable Local Span/Zero Adjustment 1, 4, 4, 1, 7

Field Device Info 1, 4, 4, 1

Keypad Input 1, 2, 3, 1, 1

Loop Test 1, 2, 2

Lower Range Value 4, 1

Lower Sensor Trim 1, 2, 3, 3, 2

Message 1, 3, 4, 3

Meter Type 1, 3, 6, 1

Number of Requested Preambles 1, 4, 3, 3, 2

Output Trim 1, 2, 3, 2

Percent Range 1, 1, 2

Poll Address 1, 4, 3, 3, 1

✓ Range Values 1, 3, 3

Rerange 1, 2, 3, 1

Scaled D/A Trim (4–20 mA Output) 1, 2, 3, 2, 2

Self Test (Transmitter) 1, 2, 1, 1

Sensor Info 1, 4, 4, 2

Sensor Trim (Full Trim) 1, 2, 3, 3

12 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

Function HART Fast Key sequence

Sensor Trim Points 1, 2, 3, 3, 5

Status 1, 2, 1, 2

✓ Tag 1, 3, 1

Transmitter Security (Write Protect) 1, 3, 4, 4

✓ Units (Process Variable) 1, 3, 2

Upper Range Value 5, 2

Upper Sensor Trim 1, 2, 3, 3, 3

Zero Trim 1, 2, 3, 3, 1

Quick Start Guide 13

Quick Start Guide February 2019

5 Trim the transmitter

Note

Transmitters are shipped fully calibrated per request or by the factory default
of full scale (span = upper range limit).

5.1 Zero trim

A zero trim is a single-point adjustment used for compensating mounting
position effects. If zero offset is less than 3 percent of true zero, follow the

Using the Field Communicator instructions below. If zero offset is greater than

3 percent of true zero, follow the Using the transmitter zero adjustment

button instructions below to rerange.

5.1.1 Using the Field Communicator

Fast Keys 1, 2, 3, 3, 1

Procedure

1. Vent the transmitter and connect Field Communicator.

2. At the menu, input the HART Fast Key sequence.

3. Follow the commands to perform a zero trim.

5.1.2 Using the transmitter zero adjustment button

Procedure

1. Loosen the certifications label screw and rotate the label to expose the
zero adjustment button.

2. Apply the desired pressure for the 4 mA output.

3. Set the 4 mA point by pressing the zero button for two seconds. Verify
that the output is 4 mA. The optional LCD display will show “ZERO
PASS”.

14 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

Example

A. Zero adjustment button

Quick Start Guide 15

Quick Start Guide February 2019

6 Safety instrumented systems

The following section applies to Rosemount 2088 Transmitters used in SIS
applications.

Note

Transmitter output is not safety-rated during the following: configuration
changes, multidrop, loop test. Alternative means should be used to ensure
process safety during transmitter configuration and maintenance activities.

6.1 Installation

No special installation is required in addition to the standard installation
practices outlined in this document. Always ensure a proper seal by installing
the electronics housing cover(s) so that metal contacts metal.

The loop must be designed so the terminal voltage does not drop below 10.5
Vdc when the transmitter output is 22.5 mA.

Position the security switch to the “ON” position to prevent accidental or
deliberate change of configuration data during normal operation.

6.2 Configuration

Use any HART-compliant master to communicate with and verify
configuration of the Rosemount 2088.

User-selected damping will affect the transmitters ability to respond to
changes in the applied process. The damping value + response time must not
exceed the loop requirements.

Note

DCS or safety logic solver must be configured to match transmitter
configuration. Figure 6-1 identifies the two alarm levels available and their
operation values. Position the alarm switch to the required HI or LO alarm
position.

Figure 6-1: Alarm Levels

Rosemount alarm level

16 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

Namur alarm level

A. Transmitter Failure, hardware alarm in LO position.
B. Transmitter Failure, hardware alarm in HI position.

Note

Some detected faults are indicated on the analog output at a level above high
alarm regardless of the alarm switch selection.

6.3 Operation and maintenance

6.3.1 Proof test and inspection

The following proof tests are recommended. Proof test results and corrective
actions taken must be documented at Emerson.com/Rosemount/Safety in
the event that an error is found in the safety functionality.

Use Table 7-1 to perform a Loop Test, Analog Output Trim, or Sensor Trim.
See the Rosemount 2088 Reference Manual for additional information.

6.3.2 Proof test

This proof test will detect 92 percent of DU failures not detected by the
Rosemount 2088 automatic diagnostics.

Procedure

1. Bypass the safety PLC and take appropriate action to avoid a false trip.

2. Send a HART command to the transmitter to go to the high alarm
current output and verify that the analog current reaches that value.

3. Send a HART command to the transmitter to go to the low alarm
current output and verify that the analog current reaches that value.

4. Perform a minimum two-point sensor calibration check using the 4-20
mA range points as the calibration points and verify that the mA
output corresponds to the pressure input value.

(3)

5. Restore loop to full operation.

(1) This tests for compliance voltage problems such as a low loop power supply voltage

or increased wiring resistance. This also tests for other possible failures.

(2) This tests for possible quiescent current related failures.
(3) If the two-point calibration is performed with electrical instrumentation, this proof

test will not detect any failures of the sensor.

Quick Start Guide 17

(1)

(2)

Quick Start Guide February 2019

6. Remove the bypass and otherwise restore normal operation.

6.3.3 Product repair

All failures detected by the transmitter diagnostics or by the proof-test must
be reported. Feedback can be submitted electronically at Emerson.com/

Rosemount/Safety.

The Rosemount 2088 is repairable by major component replacement. Follow
the instructions in the Rosemount 2088 Reference Manual for additional
information.

6.4 Reference

6.4.1 Specifications

The Rosemount 2088 must be operated in accordance to the functional and
performance specifications provided in the Rosemount 2088 Reference

Manual.

6.4.2 Failure rate data

The FMEDA report includes failure rates. This report is available at

Emerson.com/Rosemount.

6.4.3 2088 safety failure values

Safety accuracy: 2.0% Safety response time: 1.5 sec

Note

A 2% variation of the transmitter mA output is allowed before a safety trip.
Trip values in the DCS or safety logic solver should be derated by 2%.

Safety response time: 1.5 sec

6.4.4 Product life

50 years – based on worst case component wear-out mechanisms – not based
on wear-out process wetted materials.

18 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

7 Product Certifications

7.1 Rosemount™ 2088

Mount directly to the impulse line without using an additional mounting
bracket or mount directly to a wall, panel, or two-inch pipe using an optional
mounting bracket.

7.1.1 European Directive Information

A copy of the EU Declaration of Conformity can be found at the end of the
Quick Start Guide. The most recent revision of the EU Declaration of
Conformity can be found at Emerson.com/Rosemount.

7.1.2 Ordinary Location Certification

As standard, the transmitter has been examined and tested to determine that
the design meets the basic electrical, mechanical, and fire protection
requirements by a nationally recognized test laboratory (NRTL) as accredited
by the Federal Occupational Safety and Health Administration (OSHA).

7.1.3 North America

E5 USA Explosionproof (XP) and Dust-Ignitionproof (DIP)

Certificate:

Standards:

Markings:

I5 USA Safety (IS) and Nonincendive (NI)

Certificate:

Standards:

Markings:

Special Condition for Safe Use (X):

1. The Rosemount 2088 Transmitter with the transient terminal block

Quick Start Guide 19

1V2A8.AE

FM Class 3600 – 2011, FM, Class 3615 – 2006, FM Class 3616 –
2011, FM Class 3810 – 2005, ANSI/NEMA 250 – 1991

XP CL I, DIV 1, GP B, C, D; DIP CL II, DIV 1, GP E, F, G; CL III; T5(–
40 °C ≤ Ta ≤ +85 °C); Factory Sealed; Type 4X

0V9A7.AX

FM Class 3600 – 1998, FM Class 3610 – 2010, FM Class 3611 –
2004, FM Class 3810 – 1989

IS CL I, DIV 1, GP A, B, C, D; CL II, DIV 1, GP E, F, G; Class III; DIV 1
when connected per Rosemount drawing 02088-1018; NI CL 1,
DIV 2, GP A, B, C, D; T4(–40 °C ≤ Ta ≤ +70 °C); Type 4x

(Option code T1) will not pass the 500 Vrms dielectric strength test
and this must be taken into account during installation.

Quick Start Guide February 2019

C6 Canada Explosionproof, Intrinsic Safety and Division 2, Dust­Ignitionproof

Certificate:

Standards:

Markings:

7.1.4 Europe

ED ATEX Flameproof

Certificate:

Standards:

Markings:

Special Conditions for Safe Use (X):

1. This device contains a thin wall diaphragm. Installation, maintenance

1015441

CAN/CSA C22.2 No. 0-M91 (R2001), CSA Std C22.2 No.
25-1966, CSA Std C22.2 No. 30-M1986, CAN/CSA-C22.2 No.
94-M91, CSA Std C22.2 No. 142-M1987, CAN/CSA-C22.2 No.
157-92, CSA Std C22.2 No. 213-M1987, ANSI­ISA-12.27.01-2003

Explosionproof for Class I, Division 1, Groups B,C and D; Dust­Ignitionproof Class II, Division 1, Groups E, F, G; Class III
Division 1; Intrinsically Safe Class I, Division 1 Groups A, B, C, D
when connected in accordance with Rosemount drawing
02088-1024, Temperature Code T3C; Class I Division 2 Groups
A, B, C and D; Type 4X; Factory Sealed; Single Seal

KEMA97ATEX2378X

EN60079-0:2012 + A11:2013, EN60079-1:2014,
EN60079-26:2015

II 1/2 G Ex db IIC T6....T4, Ga/Gb, T6(–60 °C ≤ Ta ≤ +70 °C),

T4/T5(–60 °C ≤ Ta ≤ +80 °C)

and use shall take into account the environmental conditions to which
the diaphragm will be subjected. The manufacturer’s instructions for
installation and maintenance shall be followed in detail to assure
safety during its expected lifetime.

2. Flameproof joints are not intended for repair.

3. Non-standard paint options may cause risk from electrostatic
discharge. Avoid installations that could cause electrostatic build-up
on painted surfaces, and only clean the painted surfaces with a damp
cloth. If paint is ordered through a special option code, contact the
manufacturer for more information.

I1 ATEX Intrinsic Safety

Certificate:

Standards:

20 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

BAS00ATEX1166X

EN60079-0:2012 + A11:2013, EN60079-11:2012

February 2019 Quick Start Guide

Markings:

II 1 G Ex ia IIC T4 Ga (–55 °C ≤ Ta ≤ +70 °C)

Table 7-1: Input Parameters

Parameter HART

Voltage U

Current I

Power P

Capacitance C

i

i

i

i

30 V

200 mA

0.9 W

0.012 μF

Special Condition for Safe Use (X):

1. The apparatus is not capable of withstanding the 500 V insulation test
required by EN60079-11. This must be taken into account when
installing the apparatus.

N1 ATEX Type n

Certificate:

Standards:

Markings:

BAS00ATEX3167X

EN60079-0:2012 + A11:2013, EN60079-15:2010

II 3 G Ex nA IIC T5 Gc (–40 °C ≤ Ta ≤ +70 °C)

Special Condition for Safe Use (X):

1. The apparatus is not capable of withstanding the 500 V insulation test
required by EN60079-15. This must be taken into account when
installing the apparatus.

ND ATEX Dust

Certificate:

Standards:

Markings:

BAS01ATEX1427X

EN60079-0:2012 + A11:2013, EN60079-31:2009

II 1 D Ex t IIIC T50 °C T

60 °C Da

500

Special Conditions for Safe Use (X):

1. The user must ensure the maximum rated voltage and current (36
volts, 24 milliamps, d.c.) are not exceeded. All connection to other
apparatus or associated apparatus shall have control over this voltage
and current to a category 'ib' circuit.

2. Cable entries must be used which maintain the ingress protection of
the enclosure to at least IP66.

3. Unused cable entries must be filled with suitable blanking plugs which
maintain the ingress protection of the enclosure to at least IP66.

Quick Start Guide 21

Quick Start Guide February 2019

4. Cable entries and blanking plugs must be suitable for the ambient
range of the apparatus and capable of withstanding a 7 J impact test.

5. The Rosemount 2088/2090 sensor module must be securely screwed
in place to maintain the ingress protection of the enclosure.

7.1.5 International

E7 IECEx Flameproof

Certificate:

Standards:

Markings:

IECEx KEM 06.0021X

IEC 60079-0:2011, IEC60079-1:2014, IEC60079-26:2014

Ex d IIC T6...T4 Ga/Gb, T6(–60 °C ≤ Ta ≤ +70 °C), T4/T5 (–60 °C ≤
Ta ≤ +80 °C)

Special Conditions for Safe Use (x):

1. This device contains a thin wall diaphragm. Installation, maintenance
and use shall take into account the environmental conditions to which
the diaphragm will be subjected. The manufacturer’s instructions for
installation and maintenance shall be followed in detail to assure
safety during its expected lifetime.

2. Flameproof joints are not intended for repair.

3. Non-standard paint options may cause risk from electrostatic
discharge. Avoid installations that could cause electrostatic build-up
on painted surfaces, and only clean the painted surfaces with a damp
cloth. If paint is ordered through a special option code, contact the
manufacturer for more information.

I7 IECEx Intrinsic Safety

Certificate:

Standards:

Markings:

IECEx BAS 12.0071X

IEC60079-0:2011, IEC60079-11:2011

Ex ia IIC T4 Ga (–55 °C ≤ Ta ≤ +70 °C)

Table 7-2: Entity Parameters

Parameter HART

Voltage U

Current I

Power P

Capacitance C

22 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

i

i

i

30 V

200 mA

0.9 W

0.012 μF

i

February 2019 Quick Start Guide

Special Conditions for Safe Use (X):

1. When fitted with a transient suppression terminal block, the
Rosemount 2088 is incapable of passing the 500 V isolation test. This
must be taken into account during installation.

2. The enclosure may be made of aluminum alloy and given a protective
polyurethane paint finish; however, care should be taken to protect it
from impact or abrasion if located in a Zone 0 environment.

N7 IECEx Type n

Certificate:

Standards:

Markings:

IECEx BAS 12.0072X

IEC60079-0:2011, IEC60079-15:2010

Ex nA IIC T5 Gc (–40 °C ≤ Ta ≤ +70 °C)

Special Condition for Safe Use (X):

1. When fitted with a transient suppression terminal block, the
Rosemount 2088 is incapable of passing the 500 V isolation test. This
must be taking into account during installation.

NK IECEx Dust

Certificate:

Standards:

Markings:

IECEx BAS12.0073X

IEC60079-0:2011, IEC60079-31:2008

Ex t IIIC T50 °C T

60 °C Da

500

Table 7-3: Input Parameters

Parameter HART

Voltage U

Current I

i

i

36 V

24 mA

Special Conditions For Safe Use (x):

1. Cable entries must be used which maintain the ingress protection of
the enclosure to at least IP66.

2. Unused cable entries must be filled with suitable blanking plugs which
maintain the ingress protection of the enclosure to at least IP66.

3. Cable entries and blanking plugs must be suitable for the ambient
range of the apparatus and capable of withstanding a 7 J impact.

Quick Start Guide 23

Quick Start Guide February 2019

7.1.6 Brazil

E2 INMETRO Flameproof

Certificate:

Standards:

UL-BR 15.0728X

ABNT NBR IEC60079-0:2008 + Errata 1:2011, ABNT NBR IEC
60079-1:2009 + Errata 1:2011

Markings:

Ex d IIC T* Gb, *T4(–20 °C ≤ Ta ≤ +80 °C), *T6(–20 °C ≤ Ta ≤ +40
°C)

Special Conditions For Safe Use (x):

1. This device contains a thin wall diaphragm less than 1mm thickness
that forms a boundary between zone 0 (process connection) and zone
1 (all other parts of the equipment). The model code and data sheet
are to be consulted for details of the diaphragm material. Installations,
maintenance and use shall take into account the environmental
conditions to which the diaphragm will be subjected. The
manufacturer's instructions for installation and maintenance shall be
followed in detail to assure safety during its expected lifetime.

2. Flameproof joints are not intended for repair.

3. Non-standard paint options may cause risk from electrostatic
discharge. Avoid installations that could cause electrostatic build-up
on painted surfaces, and only clean the painted surfaces with a damp
cloth. If paint Is ordered through a special option code, contact the
manufacturer for more information.

I2 INMETRO Intrinsic Safety

Certificate:

Standards:

UL-BR 13.0246X

ABNT NBR IEC60079-0:2008 + Errata 1:2011, ABNT NBR
IEC60079-11:2009

Markings:

Ex ia IIC T4 Ga (–55 °C ≤ Ta ≤ +70 °C)

Table 7-4: Input Parameters

Parameter HART

Voltage U

Current I

Power P

Capacitance C

24 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

i

i

i

30 V

200 mA

0.9 W

0.012 μF

i

February 2019 Quick Start Guide

Special Conditions for Safe Use (X):

1. When fitted with a transient suppression terminal block, the
Rosemount 2088 is incapable of passing the 500 V isolation test. This
must be taken into account when installing the equipment.

2. The enclosure may be made of aluminum alloy and given a protective
polyurethane paint finish; however, care should be taken to protect it
from impact or abrasion if located in Zone 0.

7.1.7 China

E3 China Flameproof

Certificate:

Standards:

Markings:

GYJ15.1505

GB3836.1-2010, GB3836.2-2010

Ex d IIC T4/T6 Gb, T6(–20 °C ≤ Ta ≤ +40 °C), T4(–20 °C ≤ Ta ≤
+80 °C)

Special Conditions For Safe Use (X):

1. The ambient temperature is as follows:

T

a

–20 °C ≤ Ta ≤ 80 °C T4

–20 °C ≤ Ta ≤ 40 °C T6

Temperature class

2. The earth connection facility in the enclosure should be connected
reliably.

3. During installation in hazardous location, cable glands, conduits, and
blanking plugs, certified by state-appointed inspection bodies with Ex
d IIC type of protection, should be used.

4. During installation, use and maintenance in explosive gas
atmospheres, observe the warning “Do not open when energized”.

5. During installation, there should be no mixture harm to flameproof
housing.

6. End user is not permitted to change any components insides, but to
settle the problem in conjunction with manufacturer to avoid damage
to the product.

7. Maintenance should be done in non-hazardous location.

8. During installation, use and maintenance of this product, observe the
following standards: GB3836.13-2013, GB3836.15-2000,
GB3836.16-2006, GB50257-2014.

Quick Start Guide 25

Quick Start Guide February 2019

I3 China Intrinsic Safety

Certificate:

Standards:

Markings:

GYJ15.1507

GB3836.1-2010, GB3836.4-2010, GB3836.20-2010

Ex ia IIC T4/T5 Ga

Special Conditions for Safe Use (X):

1. The enclosure may be made of aluminum alloy and given a protective
polyurethane paint finish; however, care should be taken to protect it
from impact or abrasion if located in a zone 0 environment.

2. This apparatus is not capable of withstanding the 500 V r.m.s.
insulation test required by Clause 6.3.12 of GB3836.4-2010.

3. The ambient temperature is:

T

a

–55 °C ≤ Ta ≤ 70 °C T4

Temperature class

4. Intrinsically safe parameters:

Parameter HART

Voltage U

Current I

Power P

Capacitance C

Inductance L

i

i

i

i

i

30 V

200 mA

0.9 W

0.012 μF

0 mH

5. The product should be used with Ex-certified linear associated
apparatus to establish explosion protection system that can be used in
explosive gas atmospheres. Wiring and terminals should comply with
the instruction manual of the product and associated apparatus.

6. The cables between this product and associated apparatus should be
shielded cables (the cables must have insulated shields). The shield has
to be grounded reliably in a non-hazardous area.

7. End users are not permitted to change any internal components, but
to settle the problem in conjunction with the manufacturer to avoid
damage to the product.

8. During installation, use and maintenance of this product, observe the
following standards: GB3836.13-2013, GB3836.15-2000,
GB3836.16-2006, GB3836.18-2010, GB50257-2014.

26 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

N3 China Type n

Certificate:

Standards:

Markings:

Special Conditions For Safe Use (X):

7.1.8 Japan

GYJ15.1108X

GB3836.1-2000, GB3836. 8-2003

Ex nA nL IIC T5 Gc (–40 °C ≤ Ta ≤ +70 °C)

1. The apparatus is not capable of withstanding the 500 V r.m.s.
insulation test required by GB3836.8-2003.

2. The ambient temperature range is –40 °C ≤ Ta ≤ +70 °C.

3. Maximum input voltage: 50 V.

4. Cable glands, conduit or blanking plugs, certified by NEPSI with Ex e or
Ex n protection types should be used on external connections and
redundant cable entries.

5. Maintenance should be done in non-hazardous location.

6. End users are not permitted to change any internal components, but
to settle the problem in conjunction with manufacturer to avoid
damage to the product.

7. During installation, use and maintenance of this product, observe the
following standards: GB3836.13-2013, GB3836.15-2000,
GB3836.16-2006, GB50257-1996.

E4 Japan Flameproof

Certificate:

Markings:

TC20869, TC20870

Ex d IIC T5

7.1.9 Technical Regulations Customs Union (EAC)

EM EAC Flameproof

Certificate:

Markings:

Special Condition for Safe Use (X):

1. See certificate for special conditions.

Quick Start Guide 27

RU C-US.GB05.B.01197

Ga/Gb Ex d IIC T4/T6 X, T4(–40 °C ≤ Ta ≤ +80 °C), T6(–40 °C ≤ T
≤ +40 °C)

a

Quick Start Guide February 2019

IM EAC Intrinsically Safe

Certificate:

Markings:

RU C-US.GB05.B.01197

0Ex ia IIC T4 Ga X (–55 °C ≤ Ta ≤ +70 °C)

7.1.10 Combinations

K1 Combination of ED, I1, ND and N1

K2 Combination of E2 and I2

K5 Combination of E5 and I5

K6 Combination of C6, ED and I1

K7 Combination of E7, I7, NK and N7

KB Combination of K5 and C6

KM Combination of EM and IM

KH Combination of ED, I1, K5

7.1.11 Conduit Plugs and Adapters

IECEx Flameproof and Increased Safety

Certificate:

Standards:

Markings:

IECEx FMG 13.0032X

IEC60079-0:2011, IEC60079-1:2007-04, IEC60079-7:2006-07

Ex de IIC Gb

ATEX Flameproof and Increased Safety

Certificate:

Standards:

Markings:

FM13ATEX0076X

EN60079-0:2012, EN60079-1:2007, IEC60079-7:2007

II 2 G Ex de IIC Gb

Table 7-5: Conduit Plug Thread Sizes

Thread Identification mark

M20 × 1.5 – 6g M20

1/2–14 NPT 1/2 NPT

G1/2A G1/2

Table 7-6: Thread Adapter Thread Sizes

Male thread Identification mark

28 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

Table 7-6: Thread Adapter Thread Sizes

(continued)

M20 × 1.5 – 6H M20

1/2–14 NPT 1/2–14 NPT

3/4–14 NPT 3/4–14 NPT

Female thread Identification mark

M20 × 1.5 – 6H M20

1/2–14 NPT 1/2–14 NPT

G1/2 G1/2

Special Conditions For Safe Use (X):

1. When the thread adapter or blanking plug is used with an enclosure in
type of protection increased safety “e” the entry thread shall be
suitably sealed in order to maintain the ingress protection rating (IP) of
the enclosure.

2. The blanking plug shall not be used with an adapter.

3. Blanking Plug and Threaded Adapter shall be either NPT or Metric
thread forms. G1/2 thread forms are only acceptable for existing
(legacy) equipment installations.

7.1.12 Additional Certifications

SBS American Bureau of Shipping (ABS) Type Approval

Certificate:

Intended Use:

ABS Rules:

SBV Bureau Veritas (BV) Type Approval

Certificate:

Requirements:

Application:

Quick Start Guide 29

09-HS446883D-3-PDA

Measure gauge or absolute pressure of liquid, gas or vapor
applications on ABS classed vessels, marine, and offshore
installations.

2014 Steel Vessels Rules 1-1-4/7.7, 1-1-Appendix 3,
4-8-3/1.7, 4-8-3/13.1, 4-8-3/13.3.1 & 13.3.2, 4-8-4/27.5.1

23156/B0 BV

Bureau Veritas Rules for the Classification of Steel Ships

Class notations: AUT-UMS, AUT-CCS, AUT-PORT and AUT­IMS; Pressure transmitter type 2088 cannot be installed on
diesel engines

Quick Start Guide February 2019

SDN Det Norske Veritas (DNV) Type Approval

Certificate:

Intended Use:

Application:

TAA000004F

DNV GL Rules for Classification - Ships and offshore units

Location classes

Temperature D

Humidity B

Vibration A

EMC B

Enclosure D

SLL Lloyds Register (LR) Type Approval

Certificate:

Application:

11/60002

Environmental categories ENV1, ENV2, ENV3 and ENV5

7.2 Rosemount 2090 Product Certification

Rev 1.6

7.2.1 European Directive Information

A copy of the EU Declaration of Conformity can be found at the end of the
Quick Start Guide. The most recent revision of the EU Declaration of
Conformity can be found at EmersonProcess.com/Rosemount.

7.2.2 Ordinary Location Certification

As standard, the transmitter has been examined and tested to determine that
the design meets the basic electrical, mechanical, and fire protection
requirements by a nationally recognized test laboratory (NRTL) as accredited
by the Federal Occupational Safety and Health Administration (OSHA).

7.2.3 North America

E5 USA Explosionproof (XP) and Dust-Ignitionproof (DIP)

Certificate:

Standards:

Markings:

30 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

1V2A8.AE

FM Class 3600 – 2011, FM Class 3615 – 2006, FM class 3616 –
2011, FM Class 3810 – 2005, ANSI/NEMA 250 – 1991

XP CL I, DIV 1, GP B, C, D; DIP CL II, DIV 1, GP E, F, G; CL III, DIV
1; T5(–40 °C ≤ Ta ≤ +85 °C); Factory Sealed; Type 4X

February 2019 Quick Start Guide

I5 USA Intrinsic Safety (IS) and Nonincendive (NI)

Certificate:

Standards:

0V9A7.AX

FM Class 3600 – 1998, FM Class 3610 – 2010, FM Class 3611 –
2004, FM Class 3810 – 1989

Markings:

IS CL I, DIV 1, GP A, B, C, D; CL II, DIV 1, GP E, F, G; Class III; DIV 1
when connected per Rosemount drawing 02088-1018; NI CL 1,
DIV 2, GP A, B, C, D; T4(–40 °C ≤ Ta ≤ +70 °C); Type 4x

Special Condition for Safe Use (X):

1. The Rosemount 2090 Transmitter with the transient terminal block
(option code T1) will not pass the 500 V r.m.s.dielectric strength test
and this must be taken into account during installation.

C6 Canada Explosionproof, Intrinsically Safe, and Division 2, Dust­Ignitionproof

Certificate:

Standards:

1015441

CAN/CSA C22.2 No. 0-M91 (R2001), CSA Std C22.2 No.
25-1966, CSA Std C22.2 No. 30-M1986, CAN/CSA-C22.2 No.
94-M91, CSA Std C22.2 No. 142-M1987, CAN/CSA-C22.2 No.
157-92, CSA Std C22.2 No. 213-M1987, ANSI­ISA-12.27.01-2003

Markings:

Explosionproof for Class I, Division 1, Groups B, C and D; Class
II, Groups E, F, and G; Class III; Intrinsically Safe Class I, Division
1 when connected in accordance with Rosemount drawing
02088-1024, Temperature Code T3C; Ex ia; Class I Division 2
Groups A, B, C and D; Type 4X; Factory Sealed

7.2.4 Europe

ED ATEX Flameproof

Certificate:

Standards:

Markings:

Special Conditions for Safe Use (X):

1. This device contains a thin wall diaphragm. Installation, maintenance

Quick Start Guide 31

KEMA97ATEX2378X

EN60079-0:2012 + A11:2013, EN60079-1:2014,
EN60079-26:2015

II 1/2 G Ex db IIC T6… T4, T6(–60 °C ≤ Ta ≤ +70 °C), T4/T5(–

60 °C ≤ Ta ≤ +80 °C)

and use shall take into account the environmental conditions to which
the diaphragm will be subjected. The manufacturer’s instructions for

Quick Start Guide February 2019

installation and maintenance shall be followed in detail to assure
safety during its expected lifetime.

2. Flameproof joints are not intended for repair.

3. Non-standard paint options may cause risk from electrostatic
discharge. Avoid installations that could cause electrostatic build-up
on painted surfaces, and only clean the painted surfaces with a damp
cloth. If paint is ordered through a special option code, contact the
manufacturer for more information.

I1 ATEX Intrinsic Safety

Certificate:

Standards:

Markings:

BAS00ATEX1166X

EN60079-0:2012, EN60079-11:2012

II 1 G Ex ia IIC T5/T4 Ga, T5(–55 °C ≤ Ta ≤ +40 °C), T4(–55 °C ≤

Ta ≤ +70 °C)

Table 7-7: Input Parameters

Parameter HART

Voltage U

Current I

Power P

Capacitance C

i

i

i

i

30 V

200 mA

0.9 W

0.012 μF

Special Condition for Safe Use (X):

1. The apparatus is not capable of withstanding the 500 V insulation test
required by EN60079-11. This must be taken into account when
installing the apparatus.

N1 ATEX Type n

Certificate:

Standards:

Markings:

BAS00ATEX3167X

EN60079-0:2012, EN60079-15:2010

II 3 G Ex nA IIC T5 Gc (–40 °C ≤ Ta ≤ +70 °C)

Special Condition for Safe Use (X):

1. This apparatus is not capable of withstanding the 500 V insulation test
that is required by EN60079-15. This must be taken into account when
installing the apparatus.

32 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

ND ATEX Dust

Certificate:

Standards:

Markings:

Special Conditions for Safe Use (X):

1. The user must ensure that the maximum rated voltage and current (36
volts, 24 milliamps, d.c.) are not exceeded. All connection to other
apparatus or associated apparatus shall have control over this voltage
and current to a category ‘ib’ circuit.

2. Cable entries must be used which maintain the ingress protection of
the enclosure to at least IP66.

3. Unused cable entries must be filled with suitable blanking plugs which
maintain the ingress protection of the enclosure to at least IP66.

4. Cable entries and blanking plugs must be suitable for the ambient
range of the apparatus and capable of withstanding a 7 J impact test.

5. The Rosemount 2090 sensor module must be securely screwed in
place to maintain the ingress protection of the enclosure.

7.2.5 International

K7 Combination

IECEx Flameproof

BAS01ATEX1427X

EN60079-0:2012, EN60079-31:2009

Ex t IIIC T 50 °C T

500

60 °C Da

Certificate:

Standards:

Markings:

IECEx KEM 06.0021X

IEC60079-0:2011, IEC60079-1:2014, IEC60079-26:2014

Ex db IIC T6…T4 Ga/Gb, T6(–60 °C ≤ Ta ≤ +70 °C), T4/T5(–60 °C
≤ Ta ≤ +80 °C)

Special Conditions for Safe Use (X):

1. This device contains a thin wall diaphragm. Installation, maintenance
and use shall take into account the environmental conditions to which
the diaphragm will be subjected. The manufacturer's instructions for
installation and maintenance shall be followed in detail to assure
safety during its expected lifetime.

2. Flameproof joints are not intended for repair.

3. Non-standard paint options may cause risk from electrostatic
discharge. Avoid installations that could cause electrostatic build-up
on painted surfaces, and only clean the painted surfaces with a damp

Quick Start Guide 33

Quick Start Guide February 2019

cloth. If paint is ordered through a special option code, contact the
manufacturer for more information.

IECEx Dust

Certificate:

Standards:

Markings:

IECEx BAS12.0073X

IEC60079-0:2011, IEC60079-31:2008

Ex t IIIC T 50 °C T

500

60 °C Da

Table 7-8: Input Parameters

Parameter HART

Voltage U

Current I

i

i

36 Vdc

24 mA

Special Conditions for Safe Use (X):

1. Cable entries must be used which maintain the ingress protection of
the enclosure to at least IP66.

2. Unused cable entries must be filled with suitable blanking plugs which
maintain the ingress protection of the enclosure to at least IP66.

3. Cable entries and blanking plugs must be suitable for the ambient
temperature range of the apparatus and capable of withstanding a 7 J
impact test.

IECEx Intrinsic Safety

Certificate:

Standards:

Markings:

IECEx BAS 12.0071X

IEC60079-0:2011, IEC60079-11:2011

Ex ia IIC T5/T4 Ga, T5(–55 °C ≤ Ta ≤ +40 °C), T4(–55 °C ≤ Ta ≤
+70 °C)

Table 7-9: Input Parameters

Parameter HART

Voltage U

Current I

Power P

Capacitance C

34 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

i

i

i

i

30 V

200 mA

0.9 W

0.012 μF

February 2019 Quick Start Guide

Special Conditions for Safe Use (X):

1. When fitted with a transient suppression terminal block, the
Rosemount 2090 is incapable of passing the 500 V isolation test. This
must be taken into account during installation.

2. The enclosure may be made of aluminum alloy and given a protective
polyurethane paint finish; however, care should be taken to protect it
from impact or abrasion if located in a Zone 0 environment.

IECEx Type n

Certificate:

Standards:

Markings:

IECEx BAS 12.0072X

IEC60079-0:2011, IEC60079-15:2010

Ex nA IIC T5 Gc (–40 °C ≤ Ta ≤ +70 °C)

Special Conditions for Safe Use (X):

1. When fitted with a transient suppression terminal block, the
Rosemount 2090 is incapable of passing the 500 V isolation test. This
must be taken into account during installation.

NK IECEx Dust

Certificate:

Standards:

Markings:

IECEx BAS12.0073X

IEC60079-0:2011, IEC60079-31:2008

Ex t IIIC T 50 °C T

60 °C Da

500

Table 7-10: Input Parameters

Parameter HART

Voltage U

Current I

i

i

36 Vdc

24 mA

Special Conditions for Safe Use (X):

1. Cable entries must be used which mention the ingress protection of
the enclosure to at least IP66.

2. Unused cable entries must be filled with suitable blanking plugs which
maintain the ingress protection of the enclosure to at least IP66.

3. Cable entries and blanking plugs must be suitable for the ambient
range of the apparatus and capable of withstanding a 7 J impact test.

Quick Start Guide 35

Quick Start Guide February 2019

7.2.6 China

E3 China Flameproof

Certificate:

Standards:

Markings:

GYJ15.1506X

GB3836.1-2010, GB3836.2-2010

Ex d IIC T6/T4 Gb, T6(–20 °C ≤ Ta ≤ +40 °C), T4(–20 °C ≤ Ta ≤
+80 °C)

Special Conditions for Safe Use (X):

1. The ambient temperature is as follows:

T

a

–20 °C ≤ Ta ≤ 80 °C T4

–20 °C ≤ Ta ≤ 40 °C T6

Temperature class

2. The earth connection facility in the enclosure should be connected
reliably.

3. During installation in hazardous location, cable glands, conduits, and
blanking plugs, certified by state-appointed inspection bodies with Ex
d IIC type of protection, should be used.

4. During installation, use and maintenance in explosive gas
atmospheres, observe the warning “Do not open when energized.”

5. During installation, there should be no mixture harm to flameproof
housing.

6. End user is not permitted to change any components insides, but to
settle the problem in conjunction with manufacturer to avoid damage
to the product.

7. Maintenance should be done in non-hazardous location.

8. During installation, use and maintenance of this product, observe the
following standards: GB3836.13-2013, GB3836.15-2000,
GB3836.16-2006, GB50257-2014.

I3 China Intrinsic Safety

Certificate:

Standards:

Markings:

36 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

GYJ15.1508X

GB3836.1-2010, GB3836.4-2010, GB3836.20-2010

Ex ia IIC T4/T5 Ga

February 2019 Quick Start Guide

Special Conditions for Safe Use (X):

1. The enclosure may be made of aluminum alloy and given a protective
polyurethane paint finish; however, care should be taken to protect it
from impact or abrasion if located in a zone 0 environment.

2. This apparatus is not capable of withstanding the 500 V r.m.s.
insulation test required by Clause 6.3.12 of GB3836.4-2010.

3. The ambient temperature is:

T

a

–55 °C ≤ Ta ≤ 40 °C T5

–55 °C ≤ Ta ≤ 70 °C T4

Temperature class

4. Intrinsically safe parameters:

Parameter HART

Voltage U

Current I

Power P

Capacitance C

Inductance L

i

i

i

i

i

30 V

200 mA

0.9 W

0.012 μF

0 mH

5. The product should be used with Ex-certified linear associated
apparatus to establish explosion protection system that can be used in
explosive gas atmospheres. Wiring and terminals should comply with
the instruction manual of the product and associated apparatus.

6. The cables between this product and associated apparatus should be
shielded cables (the cables must have insulated shields). The shield has
to be grounded reliably in a non-hazardous area.

7. End users are not permitted to change any internal components, but
to settle the problem in conjunction with the manufacturer to avoid
damage to the product.

8. During installation, use and maintenance of this product, observe the
following standards: GB3836.13-2013, GB3836.15-2000,
GB3836.16-2006, G3836.18-2010, GB50257-2014.

Quick Start Guide 37

Quick Start Guide February 2019

7.2.7 Technical Regulations Customs Union (EAC)

EM EAC Flameproof

Certificate:

Markings:

Special Conditions for Safe Use (X):

See certificate for special conditions.

IM EAC Intrinsically Safe

Certificate:

Markings:

Special Conditions for Safe Use (X):

See certificate for special conditions.

7.2.8 Combinations

K1 Combination of ED, I1, ND, and N1

K5 Combination of E5 and I5

K6 Combination of C6, ED, and I1

K7 Combination of E7, I7, NK, and N7

KB Combination of K5 and C6

RU C-US.GB05.B.01197

Ga/Gb Ex d IIC T4/T6 X, T4(-40 °C ≤ Ta ≤ +80 °C), T6(-40 °C ≤ T
≤ +40 °C)

RU C-US.GB05.B.01197

0Ex ia IIC T4 Ga X (-55 °C ≤ Ta ≤ +70 °C)

a

KM Combination of EM and IM

KH Combination of ED, I1, and K5

7.2.9 Conduit plugs and adapters

IECEx Flameproof and Increased Safety

Certificate:

Standards:

Markings:

ATEX Flameproof and Increased Safety

Certificate:

Standards:

38 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

IECEx FMG 13.0032X

IEC60079-0:2011, IEC60079-1:2007, IEC60079-7:2006-2007

Ex de IIC Gb

FM13ATEX0076X

EN60079-0:2012, EN60079-1:2007, EN60079-7:2007

February 2019 Quick Start Guide

Markings:

II 2 G Ex de IIC Gb

Table 7-11: Conduit Plug Thread Sizes

Thread Identification mark

M20 × 1.5 M20

1/2–14 NPT 1/2 NPT

G1/2A G1/2

Table 7-12: Thread Adapter Thread Sizes

Male thread Identification mark

M20 × 1.5 – 6H M20

1/2–14 NPT 1/2–14 NPT

3/4–14 NPT 3/4–14 NPT

Female thread Identification mark

M20 × 1.5 – 6H M20

1/2–14 NPT 1/2–14 NPT

PG 13.5 PG 13.5

Special Conditions for Safe Use (X):

1. When the thread adapter or blanking plug is used with an enclosure in
type of protection increased safety “e” the entry thread shall be
suitably sealed in order to maintain the ingress protection rating (IP) of
the enclosure.

2. The blanking plug shall not be used with an adapter.

3. Blanking Plug and Threaded Adapter shall be either NPT or Metric
thread forms. G1/2 and PG 13.5 thread forms are only acceptable for
existing (legacy) equipment installations.

Quick Start Guide 39

EU Declaration of Conformity

No: RMD 1010 Rev. N

Page 1 of 3

We,

Rosemount, Inc.
8200 Market Boulevard
Chanhassen, MN 55317-9685
USA

declare under our sole responsibility that the product,

Rosemount Pressure Transmitters 3051P, 2051G, 2088, and 2090

manufactured by,

Rosemount, Inc.
8200 Market Boulevard
Chanhassen, MN 55317-9685
USA

to which this declaration relates, is in conformity with the provisions of the European Union
Directives, including the latest amendments, as shown in the attached schedule.

Assumption of conformity is based on the application of the harmonized standards and, when
applicable or required, a European Union notified body certification, as shown in the attached
schedule.

(signature)

Vice President of Global Quality

(function)

Chris LaPoint

(name)

1-Feb-19; Shakopee, MN USA (date of issue)

Quick Start Guide February 2019

8 Rosemount 2088 and 2090 Declaration of

Conformity

40 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

EU Declaration of Conformity

No: RMD 1010 Rev. N

Page 2 of 3

EMC Directive (2014/30/EU)

Harmonized Standards: EN 61326-1:2013, EN 61326-2-3:2013

RoHS Directive (2011/65/EU)

Model 2090F Pressure Transmitter

Harmonized Standard: EN 50581:2012

ATEX Directive (2014/34/EU)

BAS00ATEX1166X - Intrinsic Safety Certificate

Equipment Group II Category 1 G

Ex ia IIC T4 Ga

Harmonized Standards:

EN60079-0:2012 + A11:2013, EN60079-11:2012

BAS00ATEX3167X - Type n Certificate

Equipment Group II Category 3 G

Ex nA IIC T5 Gc

Harmonized Standards:

EN60079-0:2012 + A11:2013, EN60079-15:2010

BAS01ATEX1427X - Dust Certificate

Equipment Group II Category 1 D

Ex t IIIC T50°C T

500

60°C Da

Harmonized Standards:

EN60079-0:2012 + A11:2013

Other Standards:

EN60079-31:2009
(A review against EN60079-31:2014 which is harmonized, shows no significant
changes relevant to this equipment so EN60079-31:2009 continues to represent
“State of the Art”.)

KEMA97ATEX2378X - Flameproof Certificate

Equipment Group II Category 1/2 G

Ex db IIC T6...T4 Ga/Gb

Harmonized Standards:

EN 60079-0:2012 + A11:2013; EN60079-1:2014; EN60079-26:2015

February 2019 Quick Start Guide

Quick Start Guide 41

EU Declaration of Conformity

No: RMD 1010 Rev. N

Page 3 of 3

ATEX Notified Bodies

DEKRA (KEMA) [Notified Body Number: 0344]

Utrechtseweg 310, 6812 AR Arnhem
P.O. Box 5185, 6802 ED Arnhem
The Netherlands
Postbank 6794687

SGS FIMCO OY [Notified Body Number: 0598]
P.O. Box 30 (Särkiniementie 3)
00211 HELSINKI
Finland

ATEX Notified Body for Quality Assurance

SGS FIMCO OY [Notified Body Number: 0598]

P.O. Box 30 (Särkiniementie 3)
00211 HELSINKI
Finland

Quick Start Guide February 2019

42 Rosemount 2088, 2090P, and 2090F Pressure Transmitters

February 2019 Quick Start Guide

Quick Start Guide 43

*00825-0100-4690*

00825-0100-4690, Rev. GD

Quick Start Guide

February 2019

Global Headquarters

Emerson Automation Solutions
6021 Innovation Blvd.
Shakopee, MN 55379, USA

[phone] or [phone]
[phone]
[e-mail]

Latin America Regional Office

Emerson Automation Solutions
1300 Concord Terrace, Suite 400
Sunrise, FL 33323, USA

[phone]
[phone]
[e-mail]

Asia Pacific Regional Office

Emerson Automation Solutions
1 Pandan Crescent
Singapore 128461

[phone]
[phone]
[e-mail]

North America Regional Office

Emerson Automation Solutions
8200 Market Blvd.
Chanhassen, MN 55317, USA

[phone] or [phone]
[phone]
[e-mail]

Europe Regional Office

Emerson Automation Solutions Europe
GmbH
Neuhofstrasse 19a P.O. Box 1046
CH 6340 Baar
Switzerland

[phone]
[phone]
[e-mail]

Middle East and Africa Regional Office

Emerson Automation Solutions
Emerson FZE P.O. Box 17033
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates

[phone]
[phone]
[e-mail]

Linkedin.com/company/Emerson-

Automation-Solutions

Twitter.com/Rosemount_News

Facebook.com/Rosemount

Youtube.com/user/

RosemountMeasurement

Google.com/+RosemountMeasurement

©

2019 Emerson. All rights reserved.

Emerson Terms and Conditions of Sale are
available upon request. The Emerson logo is a
trademark and service mark of Emerson Electric
Co. Rosemount is mark of one of the Emerson
family of companies. All other marks are the
property of their respective owners.