Rosemount 1055 pH Analzyer Manuals & Guides

Model Solu Comp®II

Dual Input pH Analyzer

Model Options 1055-22-32 and 1055-22

Instruction Manual

PN 51-1055pH/rev.M
February 2006

ESSENTIAL INSTRUCTIONS

READ THIS PAGE BEFORE PROCEEDING!

Your purchase from Rosemount Analytical, Inc. has
resulted in one of the finest instruments available for
your particular application. These instruments have
been designed, and tested to meet many national and
international standards. Experience indicates that its
performance is directly related to the quality of the
installation and knowledge of the user in operating and
maintaining the instrument. To ensure their continued
operation to the design specifications, personnel
should read this manual thoroughly before proceeding
with installation, commissioning, operation, and main­tenance of this instrument. If this equipment is used in
a manner not specified by the manufacturer, the pro­tection provided by it against hazards may be impaired.

• Failure to follow the proper instructions may cause
any one of the following situations to occur: Loss of
life; personal injury; property damage; damage to
this instrument; and warranty invalidation.

• Ensure that you have received the correct model
and options from your purchase order. Verify that
this manual covers your model and options. If not,
call 1-800-854-8257 or 949-757-8500 to request
correct manual.

• For clarification of instructions, contact your
Rosemount representative.

• Follow all warnings, cautions, and instructions
marked on and supplied with the product.

• Use only qualified personnel to install, operate,
update, program and maintain the product.

• Educate your personnel in the proper installation,
operation, and maintenance of the product.

• Install equipment as specified in the Installation
section of this manual. Follow appropriate local and
national codes. Only connect the product to electri­cal and pressure sources specified in this manual.

• Use only factory documented components for repair.
Tampering or unauthorized substitution of parts and
procedures can affect the performance and cause
unsafe operation of your process.

• All equipment doors must be closed and protective
covers must be in place unless qualified personnel
are performing maintenance.

• If this equipment is used in a manner not specified
by the manufacturer, the protection provided by it
against hazards may be impaired.

WARNINGS

RISK OF ELECTRICAL SHOCK

Equipment protected throughout by double insulation.

• Installation of cable connections and servicing of this
product require access to shock hazard voltage levels.

• Main power and relay contacts wired to separate power
source must be disconnected before servicing.

• Do not operate or energize instrument with case open!

• Signal wiring connected in this box must be rated at
least 240 V.

• Non-metallic cable strain reliefs do not provide grounding
between conduit connections! Use grounding type bush­ings and jumper wires.

• Unused cable conduit entries must be securely sealed by
non-flammable closures to provide enclosure integrity in
compliance with personal safety and environmental pro­tection requirements. Unused conduit openings must be
sealed with NEMA 4X or IP65 conduit plugs to maintain
the ingress protection rating (NEMA 4X).

• Electrical installation must be in accordance with the
National Electrical Code (ANSI/NFPA-70) and/or any
other applicable national or local codes.

• Operate only with front and rear panels fastened and in
place over terminal area.

• Safety and performance require that this instrument be
connected and properly grounded through a three-wire
power source.

• Proper relay use and configuration is the responsibility

of the user.

CAUTION

This product generates, uses, and can radiate radio fre­quency energy and thus can cause radio communication
interference. Improper installation, or operation, may
increase such interference. As temporarily permitted by
regulation, this unit has not been tested for compliance
within the limits of Class A computing devices, pursuant to
Subpart J of Part 15, of FCC Rules, which are designed to
provide reasonable protection against such interference.
Operation of this equipment in a residential area may cause
interference, in which case the user at his own expense, will
be required to take whatever measures may be required to
correct the interference.

WARNING

This product is not intended for use in the light
industrial, residential or commercial environments
per the instrument’s certification to EN50081-2.

Emerson Process Management

Rosemount Analytical Inc.

2400 Barranca Parkway
Irvine, CA 92606 USA
Tel: [phone]
Fax: [phone]

http://www.raihome.com

© Rosemount Analytical Inc. 2005

QUICK START GUIDE

FOR MODEL SOLU COMP II pH/ORP ANALYZER

(Model Options 1055-22-32 and 1055-22)

1. Refer to Section 2.0 for installation instructions.

2. Wire pH (or ORP) sensor(s) to the analyzer. See the drawings below. Refer to the sensor instruction sheet for
details. Make alarm, output, and power connections as shown below.

CONTINUED ON THE FOLLOWING PAGE

3. Once connections are secured and verified, apply power to the analyzer.

Wiring Connections for Solu Comp II Model 1055-01-10

(Panel Mount with 115/230 Vac Power)

Wiring Connections for Solu Comp II Model 1055-02-10

(Panel Mount with 24 Vdc Power)

Wiring Connections for Solu Comp II Model 1055-01-11

(Surface/Pipe Mounting with 115/230 Vac Power)

Wiring Connections for Solu Comp II Model 1055-02-11

(Surface/Pipe Mounting with 24 Vdc Power)

5. Choose the desired language. Choose >> to show more choices.

6. Choose the number of sensors wired to the analyzer.

NOTE

If One sensor is selected, only

S1 will be available. S2 cannot be disabled.

7. Choose the measurement for sensor 1.

8. Choose the measurement for sensor 2.

9. Choose temperature units.

10. The main display appears. The outputs and alarms are assigned to default val­ues. To change settings, refer to Section 5.0, Programming the Analyzer. To
reinstall factory settings and return to Quick Start, see Section 5.10.

# of sensors?

One

TTwwoo

Temperature in?

*

CC

*

F

S1 Measure?

ppHH

Redox ORP

S2 Measure?

ppHH

Redox ORP

4. When the analyzer is powered up for the first time, Quick Start screens appear. Using Quick Start is easy.

a. A blinking field shows the position of the cursor.

b. Use the  or  key to move the cursor left or right. Use the  or  key to move the cursor up or down or to

increase or decrease the value of a digit. Use the  or  key to move the decimal point.

c. Press ENTER to store a setting. Press EXIT to leave without storing changes. Pressing EXIT also returns the

display to the previous screen.

EEnngglliisshh

Fran ais

Espa ol >>

QUICK REFERENCE GUIDE

MENU TREE FOR pH/ORP/REDOX MEASUREMENTS

About This Document

This manual contains instructions for installation and operation of the Solu Comp II
Model 1055 Dual Input pH Analyzer.

The following list provides notes concerning all revisions of this document.

Rev

. Level

Date Notes

0 7/00 This is the initial release of the product manual. The manual

has been reformatted to reflect the Emerson documentation
style and updated to reflect any changes in the product offering.

A 2/02 Update specs (p. 2).

B 7/02 Added UL specs info

C 9/02 Fixed minor typos throughout

D 10/02 deleted option code -41 reference of p. 3

E 2/03 Revised specs & maintenance info (p. 5, 9, 45, 46)

F 4/03 Update CE specs info (p. 2, 9)

G 2/04 Update H

2SO4

specs info & recommended sensors (p. 4)

H 5/04 Updated list of compatible sensors

I 9/04 Update pipe and surface mounting drawings

J 11/04 Update panel mounting drawing

K 12/04 Revise USP references

L 4/05 Revise mounting drawing on p.12

M 2.06 Revise Case and Analog Output specifications on page 2.

i

MODEL SOLU COMP II TABLE OF CONTENTS

MODEL SOLU COMP II DUAL INPUT pH ANALYZER

TABLE OF CONTENTS

Section Title Page

1.0 DESCRIPTION AND SPECIFICATIONS ................................................................ 1

1.1 Features and Applications........................................................................................ 1

1.2 Specifications........................................................................................................... 2

1.3 Ordering Information and Accessories..................................................................... 8

2.0 INSTALLATION ....................................................................................................... 11

2.1 Unpacking and Inspection........................................................................................ 11

2.2 Installation................................................................................................................ 11

3.0 WIRING.................................................................................................................... 15

3.1 Preparing Conduit Openings.................................................................................... 15

3.2 Power, Alarm, Output, and Sensor Connections ..................................................... 15

4.0 DISPLAY AND OPERATION ................................................................................... 18

4.1 Display ..................................................................................................................... 18

4.2 Keypad..................................................................................................................... 18

4.3 Programming and Calibrating the Solu Comp II - Tutorial ....................................... 19

4.4 Security .................................................................................................................... 20

4.5 Using Hold ............................................................................................................... 20

5.0 PROGRAMMING THE ANALYZER ........................................................................ 21

5.1 General .................................................................................................................... 21

5.2 Changing StartUp Settings....................................................................................... 21

5.3 Configuring and Ranging the Outputs...................................................................... 23

5.4 Configuring Alarms and Assigning Setpoints ........................................................... 25

5.5 Selecting Type of Measurement and Activating Solution Temperature Correction .. 28

5.6 Choosing Temperature Units and Manual/Automatic Temperature Compensation . 30

5.7 Setting a Security Code ........................................................................................... 31

5.8 Noise Rejection........................................................................................................ 31

5.9 Single Sensor or Dual Sensor Input......................................................................... 32

5.10 Resetting Factory Calibration and Factory Default Settings .................................... 32

5.11 Selecting a Default Screen, Language, and Screen Contrast ................................. 33

6.0 CALIBRATION ........................................................................................................ 35

6.1 Introduction .............................................................................................................. 35

6.2 Calibrating Temperature........................................................................................... 35

6.3 Two-Point Buffer Calibration (Auto Calibration) ....................................................... 37

6.4 Two-Point Buffer Calibration (Manual Calibration) ................................................... 39

6.5 Making the Analyzer Reading Match a Second Instrument (Standardization) ......... 41

6.6 Entering a Known Slope .......................................................................................... 42

6.7 ORP Calibration ....................................................................................................... 43

7.0 MAINTENANCE ..................................................................................................... 44

7.1 Overview .................................................................................................................. 44

7.2 Replacement Parts .................................................................................................. 44

8.0 TROUBLESHOOTING ............................................................................................ 47

8.1 Overview .................................................................................................................. 47

8.2 Troubleshooting Using Fault Codes......................................................................... 47

8.3 Troubleshooting When No Error Message is Showing ............................................ 48

8.4 Simulating Inputs ..................................................................................................... 51

8.5 Simulating Temperature ........................................................................................... 52

8.6 Measuring Reference Voltage.................................................................................. 53

9.0 RETURN OF MATERIAL ........................................................................................ 54

MODEL SOLU COMP II TABLE OF CONTENTS

TABLE OF CONTENTS CONT’D

LIST OF FIGURES

Number Title Page

2-1 Panel Mount Installation ........................................................................................... 12

2-2 Pipe Mount Installation ............................................................................................. 13

2-3 Surface Mount Installation........................................................................................ 14

3-1 Removing the Knockouts ......................................................................................... 15

3-2 Wiring Connections for Solu Comp II Model 1055pH-01-10 ....................................

(Panel Mount with 115/230 Vac Power).................................................................... 16

3-3 Wiring Connections for Solu Comp II Model 1055pH-02-10 ....................................

(Panel Mount with 24 Vdc Power) ............................................................................ 16

3-4 Wiring Connections for Solu Comp II Model 1055pH-01-11 ....................................

(Wall/Pipe Mounting with 115/230 Vac Power)......................................................... 17

3-5 Wiring Connections for Solu Comp II Model 1055pH-02-11 ....................................

(Wall/Pipe Mounting with 24 Vdc Power) ................................................................. 17

4-1 Displays During Normal Operation........................................................................... 18

4-2 Solu Comp II Keypad ............................................................................................... 18

5-1 Assigning Outputs 1 and 2 ...................................................................................... 23

5-2 High Alarm Logic ..................................................................................................... 25

5-3 Low Alarm Logic ....................................................................................................... 25

6-1 Calibration Slope and Offset .................................................................................... 37

7-1 Exploded View of Solu Comp II (Panel Mount Version) ........................................... 45

7-2 Exploded View of Solu Comp II (Pipe/Surface Mount Version) ................................ 46

8-1 Simulating Inputs When the Preamplifier is in the Analyzer ..................................... 51

8-2 Simulating pH Input When the Preamplifier is in the Sensor.................................... 52

8-3 Three-Wire RTD Inputs ............................................................................................ 52

8-4 Simulating RTD Inputs.............................................................................................. 53

8-5 Checking for a Poisoned Reference Electrode ........................................................ 53

LIST OF TABLES

Number Title Page

5-1 Default Settings ........................................................................................................ 22

7-1 Replacement Parts for Solu Comp II (Panel Mount Version) ................................... 45

7-2 Replacement Parts for Solu Comp II (Pipe/Surface Mount Version) ........................ 46

ii

1

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

SECTION 1.0.

DESCRIPTION AND SPECIFICATIONS

1.1 FEATURES AND APPLICATIONS

1.2 SPECIFICATIONS

1.3 ORDERING INFORMATION AND ACCESSORIES

1.1 FEATURES AND APPLICATIONS

The Solu Comp II analyzers offer the choice of sin­gle or dual sensor input with measurement choices
of pH/ORP, resistivity/conductivity/TDS, % concen­tration, ratio conductivity, total and free chlorine, dis­solved oxygen, dissolved ozone, flow and tempera­ture. Dual measurement analyzers offer a wide
choice of measurement combinations thus reducing
the cost per loop and needed panel space.

FIELD COMMISSION OPTION: The Solu Comp II
can be ordered with the ability to commission meas­urements in the field. This added flexibility can
greatly reduce the number of spare instruments
required for field servicing.

QUICK START PROGRAMMING: Exclusive Quick
Start screens appear the first time the Solu Comp II
is powered up. Screen prompts direct the user to
register the number of sensors, the measurement
unit(s) and the language to display. Some measure­ment specific prompts are also displayed. The
measurement loop is ready for use in a matter of
minutes.

MENUS: Menu screens for calibrating and register­ing choices are simple and intuitive. Plain language
prompts guide the user through the procedures.
There are no service codes to enter before gaining
access to menus.

DUAL SENSOR INPUT AND OUTPUT: The Solu
Comp II accepts single or dual sensor input. The
two 4-20 mA outputs can be independently pro­grammed to correspond to any selected measure­ment or temperature. Output damping and linear or
log output may also be field selected.

ALARMS: The Solu Comp II has three fully pro­grammable alarm relays that can be assigned to
any selected measurement or temperature. Alarms
can be configured as high, low, or USP1. The third
relay has the additional choice of fault alarm opera­tion. When selected, a fault alarm will activate the
relay when a sensor or analyzer fault occurs.

ENCLOSURE: The panel mount version fits stan­dard ½ DIN panel cutouts, and its shallow depth is
ideally suited for easy mounting in Hoffman-type
enclosures. A panel mount gasket is included to
maintain the weather rating of the panel.
Surface/pipe mount enclosure includes self-tapping
screws for surface mounting. A pipe mounting
accessory kit is available for mounting to a 2-inch
pipe.

DISPLAY: The two-line, 16-character, back-lit dis­play can be customized to meet user requirements.
All operations and descriptive messages can be
field selected for English, French, German, Italian,
Spanish, or Portuguese. Informative screens, which
permit data not shown in the regular display, may
be seen at the push of a button.

TEMPERATURE: Most measurements (except
ORP and flow) require temperature compensation.
The Solu Comp II will automatically recognize either
a Pt100 or Pt1000 RTD, normally built into the sen­sor. When this RTD is present, the Solu Comp II
can be set up to display the temperature in °C or °F
as well as set any one or more of the alarms and/or
outputs to respond to this sensor input. If two meas­urements with temperature are present either can
be chosen for each alarm and output selected.

1

USP alarm applies to conductivity/resistivity only.

2

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

1.2 SPECIFICATIONS - General

Case: ABS (panel-mount), polycarbonate (pipe- and

surface-mount). All versions are NEMA 4X/CSA 4
(IP65).

Dimensions

Panel (code -10): 6.10 x 6.10 x 3.72 in. (155 x

155 x 94.5 mm)
Surface/Pipe (code -11): 6.23 x 6.23 x 3.23 in.

(158 x 158 x 82 mm); see page 5 for dimensions
of pipe mounting bracket.

Conduit openings: Accepts PG13.5 or 1/2 in. con-

duit fittings

Display: Two line, 16-character, back-lit display.

Character height: 4.8 mm. Display can be cus­tomized to meet individual requirements.
Depending on number of sensors, as many as 14
display screens are available.

Ambient temperature and humidity: 0 to 50°C, (32

to 122°F) RH 5 to 95% (non-condensing)
Note: The analyzer is operable from -20 to 60°C

(-4 to 140°F) with some degradation in display
performance.

Power:

Code -01:

115/230 Vac

±15%, 50/60 Hz ±6%, 8.0W

Code -02*: 24 Vdc ±15%, 6.0W

Installation Category II

*

For +24Vdc Power Supply use only devices meeting
NEC Class II or UL recognized (UL 1950).

Equipment protected throughout by double insula­tion.

Hazardous Location:

Class I, Division 2,
Groups A, B, C, & D

POLLUTION DEGREE 4: Extended Environment

Outdoor use where conductive contamination
such as rain, snow, or dust may be present.

(Hazardous Location only)

RFI/EMI: EN-61326
LVD: EN-61010-1

Input: Choice of single or dual sensor input with

measurement choices of pH/ORP, conductivity/
resistivity, toroidal conductivity, flow, chlorine, dis­solved oxygen, and dissolved ozone. Field-com­missioned units allow user to change measure­ments on either or both inputs. See combination
guide for valid combinations. For contacting con­ductivity measurements, temperature element
must be a Pt 1000 RTD. For other measure­ments, use either a Pt100 RTD, Pt1000 RTD, or
22k NTC (D.O. only).

Outputs: Two 4-20 mA or 0-20 mA isolated outputs.

Continuously adjustable. Linear or logarithmic.
Maximum load 500 ohms. Output dampening with
time constant of 5 sec is user-selectable.

Alarms: Three alarm relays for process measure-

ment(s) or temperature. Alarm 3 can be
configured as a fault alarm, instead of a

process alarm. Each relay can be configured
independently. Alarm logic (high or low activation
or USP*) and deadband are user-programmable.
The USP* alarm can be programmed to activate
when the conductivity is within a user-selectable
percentage of the limit.

*conductivity/resistivity measurement only

Relays: Form C, single pole double throw, epoxy sealed

Terminal Connections Rating: 26-14 AWG wire size

Weight/Shipping weight (rounded up to nearest lb or

nearest 0.5 kg): 3 lb (1.5 kg)/4 lb (2.0 kg)

Resistive Inductive

28 Vdc 5.0 A 3.0 A
115 Vac 5.0 A 3.0 A
230 Vac 5.0 A 1.5 A

Ordinary Location: (-68 only)

POLLUTION DEGREE 2: Normally only non-con­ductive pollution occurs. Occasionally, however, a
temporary conductivity caused by condensation
must be expected.

12RN

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

Measures conductivity in the range 0 to 20,000 µS/cm.
Display choices are conductivity, resistivity, and TDS
(total dissolved solids). Three temperature corrections
are available: high purity water (dilute sodium chlo­ride), cation conductivity (dilute hydrochloric acid),
and adjustable linear temperature coefficient (0 to

5.00%/°C). Temperature correction can be disabled,
allowing the analyzer to display raw conductivity.

PERFORMANCE SPECIFICATIONS -

ANALYZER (CONDUCTIVITY INPUT)

Accuracy (Resistivity)**: 0.9% of reading

Accuracy (Temperature)**: ±0.1°C between 5°C and

100°C; ±1°C between 101°C and 200°C

Stability: 0.5% of reading/month

Ambient Temperature Effect: ±0.05% of reading/°C

Output Accuracy: ±0.1 mA

Temperature correction: High purity water (dilute

sodium chloride), cation conductivity (dilute
hydrochloric acid), linear temperature coefficient
(0.0 to 5.00%/°C), or none. High purity water and
cation conductivity temperature correction apply
between 0 and 100°C. Linear temperature coeffi­cient can be applied between -5 and 200°C.

Measurement Range: 0.0 to 20,000 µS/cm, 0.05 to

20 MΩ-cm, or 0 to 10,000 ppm TDS

Temperature Range: -5°C to 200°C (23°F to 392°F)

1

whichever is greater

2

Accuracy values pertain to Endurance Model 400
Series conductivity sensors only

RECOMMENDED SENSORS FOR
CONDUCTIVITY:

The Solu Comp II is intended for use with the
ENDURANCE Model 400 series conductivity sensor
(Pt 1000 RTD).

Model 400 Screw-in/Insertion

Model 400VP Screw-in/Insertion with 6.0 VP connector

Model 401 Screw-in/Insertion (except 401-15)

Model 402 Retractable

Model 402VP Retractable with 6.0 VP connector

Model 403 Sanitary Flanged

Model 403VP Sanitary Flanged with 6.0 VP connector

Model 404 Flow-Through

The analyzer can also be used with Rosemount
Analytical conductivity sensor Models 140, 141, 142, and
150 having a Pt 100 RTD.

Refer to the table to select the appropriate cell constant.

Ratio Conductivity (Codes -20-30):

The dual conductivity Solu Comp II can function as a
ratio analyzer or recovery device (% passage or %
rejection). Product sensor 2’s conductivity reading is
always displayed.

Ratio

%Pass

%Reject

CONTACTING CONDUCTIVITY (Codes -20 and/or -30)

Range Cell constant (/cm) Accuracy

1,2

0.055 - 9.99 µS/cm 0.01 0.9% of reading
or ±0.002 µS/cm

10 - 50 µS/cm 0.01 ±2% of reading

0.055 - 500 µS/cm 0.1 ±2% of reading
or ±0.1 µS/cm

0.055 - 5000 µS/cm 1.0 ±2% of reading
or ±1 µS/cm

0 - 5 mS/cm 1.0 ±2% of reading

or ±0.001 mS/cm

0 - 20 mS/cm 10 ±2% of reading

or ±0.01 mS/cm

Range, µµS/cm Cell constant, /cm

0.0 to 50 0.01
5 to 500 0.1

50 to 5,000 1.0

500 to 20,000 10

12.34 µS/cm 40.3 C

7.34pH 25.3 C

Ratio .3325

S2 4.621 µS/cm

%Passage 12.1

S2 4.621 µS/cm

%Reject 87.9

S2 4.621 µS/cm

3

4

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

When used with Model Series 200 Toroidal
Conductivity Sensors, display choices are conductiv­ity, resistivity, and percent concentration. The per­cent concentration selection includes the choice of
four common solutions (0-12% NaOH, 0-15% HCl,
and 0-25% or 96-99.7% H2SO4). The conductivity­concentration algorithms for these solutions are fully
temperature compensated. For other solutions, a
simple-to-use menu allows the customer to enter his
own data. The analyzer accepts as many as five (5)
data points and fits either a linear (two [2] points) or
a quadratic function (three [3] or more points) to the
data. Reference temperature and linear temperature
slope may also be adjusted for optimum results.

PERFORMANCE SPECIFICATIONS -

Measurement Range: see table below

Accuracy: ± 1% of reading and ± 0.01 mS/cm

Repeatability: ± 0.5% of reading and ± 0.005 mS/cm

Stability: ± 0.25% of reading and ± 0.005 mS/cm/month,

noncumulative

Ambient Temperature Effect: ± 0.05% of reading/°C

Temperature Compensation: -15 to 200°C (5 to

392°F) automatic or manual. Automatic requires
a Pt100/1000 RTD

Temperature correction: Linear temperature

coefficient (0.0 to 5.00%/°C) neutral salt (dilute
sodium chloride) or none

RECOMMENDED SENSORS:

Model 222 Flow-through conductivity sensor

Model 225 Clean-in-place conductivity sensor

Model 226 Large bore conductivity sensor

Model 228 Toroidal conductivity sensor

Model 242 Flow-through conductivity sensor

Model 247 Economy conductivity sensor

TOROIDAL CONDUCTIVITY (Codes -21 and/or -31)

FULL SCALE MICROSIEMENS/cm

INDUCTIVE SENSORS

Conductivity Sensor

Model Number 226 228 225 222 (1in.) 222 (2 in.)

Cell Constant* 1.0 3.0 3.0 6.0 4.0

Minimum Range 50 250 250 500 500

Maximum Range 1,000,000 2,000,000 2,000,000 2,000,000 2,000,000

* Typical

S1 1027mS/cm 100 C

S2 847.1µS/cm 100 C

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

For use with any standard pH or ORP sensor and all
Uniloc sensors and junction boxes with built-in diag­nostic style preamplifiers, display choices are pH,
ORP or Redox. The automatic buffer recognition fea­ture uses stored buffer values and their temperature
curves for the most common buffer standards avail­able worldwide. The analyzer will recognize the value
of the buffer being measured and perform a self stabi­lization check on the sensor before completing the
calibration. Manual or automatic temperature compen­sation is keypad selectable. Change in pH due to
process temperature can be compensated using a
programmable temperature coefficient or isopotential
point. Measurement and display of pH glass and ref­erence impedance helps alert the user to sensor
maintenance needs.

*reference impedance is suppressed with amperometric/pH
combinations (-24, -25, -26)

PERFORMANCE SPECIFICATIONS ­ANALYZER (pH INPUT)

Measurement Range [pH]: 0 to 14 pH

Accuracy: ±0.01 pH

Repeatability: ±0.01 pH

Stability: ±0.01 pH/month, non-cumulative

Temperature Coefficient: ±0.003 pH/°C

Temperature Compensation: Pt100/Pt1000 RTD,

Automatic or Manual -15 to 100°C (5 to 212°F)

Temperature Correction: Choose from standard

measurement compensation, solution temperature
correction for high purity or dilute base solutions,
and custom temperature correction.

PERFORMANCE SPECIFICATIONS ­ANALYZER (ORP INPUT)

Measurement Range [ORP]: -1400 to +1400 mV

Accuracy: ±2.0 mV

Repeatability: ±1.0 mV

Stability: ±1.0 mV/month, non-cumulative

Temperature Coefficient: ± 0.2 mV/°C

Temperature Measurement: -15 to 100°C

(5 to 212°F)

Temperature Correction: none required

RECOMMENDED SENSORS FOR pH:

Model 320B Flow Through pH
Model 320HP High Purity pH
Model 328A Steam Sterilizable pH
Model 370 and 371 EuroSenz pH
Model 381+ Insertion/Submersion/Flow Through pH
Model 385+ Insertion/Submersion/Retractable pH
Model 389 Insertion/Submersion pH
Model 396 Insertion/Submersion pH
Model 396VP Insertion/Submersion pH with VP 6.0 connector
Model 396P Insertion/Submersion pH
Model 396PVP Insertion/Submersion pH with VP 6.0 connector
Model 396R Retractable pH
Model 396RVP Retractable pH with VP 6.0 connector
Model 397 Quik Disconnect pH
Model 398 Insertion/Submersion pH
Model 398VP Insertion/Submersion with VP 6.0 connector
Model 398R Retractable pH
Model 398RVP Retractable pH with VP 6.0 connector
Model 399 Insertion/Submersion pH
Model Hx338 Steam Sterilizable pH
Model Hx348 Steam Sterilizable pH

RECOMMENDED SENSORS FOR ORP:

Model 330 Flow Through ORP
Model 371 EuroSenz ORP
Model 381+ Insertion/Submersion/Flow Through ORP
Model 385+ Insertion/Submersion/Retractable pH
Model 389 Insertion/Submersion ORP
Model 396P Insertion/Submersion ORP
Model 396PVP Insertion/Submersion ORP with VP 6.0 connector
Model 396R Retractable ORP
Model 398 Insertion/Submersion ORP
Model 398VP Insertion/Submersion with VP 6.0 connector
Model 398R Retractable ORP
Model 398RVP Retractable ORP with VP 6.0 connector

When used with conductivity (-20-32 or -22-30):

Model 320HP High Purity ORP
Model 381+ Insertion/Submersion/Flow Through ORP
Model 385+ Insertion/Submersion/Retractable ORP
Model 396P Insertion/Submersion ORP
Model 396PVP Insertion/Submersion ORP with VP 6.0 connector
Model 396R Retractable ORP
Model 396RVP Retractable ORP with VP 6.0 connector

pH/ORP (Codes -22 and/or -32)

S1 4.34pH 25 C

S2 12.34pH 27 C

5

6

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

When used with a chlorine specific membrane-covered
amperometric sensor, display choices are free chlorine
or total chlorine. (Total chlorine measurement requires
the use of the Model SCS921 or other sample condi­tioning system). Because the permeability of the mem­brane is a function of temperature, a correction is nec­essary when the sensor is used at a temperature dif­ferent from the one at which it was calibrated. The
Solu Comp II automatically applies the temperature
correction factor. The process temperature is meas­ured by an RTD in the sensor. An input filter allows the
user to configure the analyzer for rapid response or
low noise. The low noise option is recommended for
samples containing less than 0.1 ppm chlorine.

pH is also a factor in the measurement of free chlo­rine. An aqueous solution of free chlorine is a mixture
of hypochlorous acid and hypochlorite ion. The rela­tive amount of each depends on the temperature and
pH. Generally, increasing the pH and temperature
reduces the amount of hypochlorous acid in the mix­ture. Because the response of the sensor to
hypochlorous acid is greater than its response to
hypochlorite, accurate determination of chlorine
requires knowledge of the pH and temperature of the
sample. If the pH is relatively constant, a fixed pH cor­rection factor can be entered into the analyzer. If the
pH is greater than 7 and fluctuates by more than 0.2,
continuous measurement of the pH and automatic pH
correction is necessary. For automatic pH correction,
select code -32 and an appropriate pH sensor.

PERFORMANCE SPECIFICATIONS

Measurement Range: 0-20 ppm (mg/L) chlorine

(as Cl2)

Resolution: 0.001 ppm
Automatic pH Correction (requires Code -32): 5.0

to 9.5 pH

Temperature Correction: Automatic (with Pt100 RTD

in sensor) or manual 0-50°C. Can be disabled if
desired.

Input filter: time constant 1 - 999 sec

RECOMMENDED SENSORS

Chlorine: 499A CL-01 Free Chlorine or 499A CL-02

Total Residual Chlorine (requires sample condi­tioning)

pH: 399-09-62, 399VP-09, 399-14

For use with most pulse signal flow sensors, the Solu
Comp II's user selectable units of measure include
flow rates in GPM (Gallon per minute), LPM (liters per
minute), or m3/hr (cubic meters per hour), and veloci­ty in ft/sec or m/sec. When configured to measure
flow, the unit also acts as a totalizer in the chosen unit
(gallons, liters, or cubic meters).

Dual flow instruments can be configured as a %
recovery device or a flow difference device.

PERFORMANCE SPECIFICATIONS

Frequency Range: 0.5 - 4000 Hz
Flow Rate: 0 - 9999 GPM, LPM, m3/hr
Totalized Flow: 0 - 9,999,999 Gallons;

37,850,000 Liters; 37,850 m3

Accuracy: ±1% (±1.5% from 3000 to 4000 Hz)
Repeatability: ±1%

RECOMMENDED SENSORS

+GF+ Signet 515 Rotor-X Flow sensor Model

515/8510-XX (PN P51530-PO)

Fluidyne Flow Sensor Model 2300A

(PN Hydro-Flow-2300-A-10-5R-3-1-1)

Consult factory for other pulse type sensor compatibility.

FREE AND TOTAL CHLORINE (Code -24)

FLOW

(Standard on all models or stand alone, Code -23 and/or -33)

S2 12.34 GPM

S2 47.25K Gal

12.34 ppm

26.3 C 8.34pH

7

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

When used with an oxygen permeable membrane­covered amperometric sensor, display choices are
ppb or ppm dissolved oxygen or % saturation.
Because the permeability of the membrane is a func­tion of temperature, a correction is necessary when
the sensor is used at a temperature different from the
one at which it was calibrated. The Solu Comp II
automatically applies the temperature correction fac­tor. The process temperature is measured by an RTD
in the sensor. Calibrating the analyzer is as simple as
exposing the sensor to air and keying in the baromet­ric pressure. If removing the sensor from the process
is impractical, the analyzer can also be calibrated
against a standard instrument. Solubility correction
factors for liquids containing high concentrations of
electrolytes can be registered into the analyzer. The
Solu Comp II automatically calculates ppb/ppm dis­solved oxygen taking into account the high salt con­centration.

PERFORMANCE SPECIFICATIONS

Measurement Range: 0-20 ppm (mg/L) dissolved

oxygen; 0- 250% saturation

Resolution: 0.01 ppm; 0.1 ppb for 499A TrDO sensor

(when O2<1.00 ppm); 0.1%

Temperature Correction for Membrane Permeability:

Automatic (with Pt100 RTD in sensor) or manual
0-50°C. Can be disabled if desired.

Input filter: 1- 255 samples

RECOMMENDED SENSORS

Model 499A DO Dissolved Oxygen Sensor
Model 499A TrDO Trace Dissolved Oxygen Sensor
Model Hx438 Steam Sterilizable Dissolved Oxygen

Sensor

Model Gx438 Steam Sterilizable Dissolved Oxygen

Sensor

Model Bx438 Steam Sterilizable Dissolved Oxygen

Sensor

DISSOLVED OXYGEN (Code -25)

For use with an ozone permeable membrane-covered
amperometric sensor. Because the permeability of the
membrane is a function of temperature, a correction is
necessary when the sensor is used at a temperature
different from the one at which it was calibrated. The
Solu Comp II automatically applies the temperature
correction factor. The process temperature is meas­ured by an RTD in the sensor. The Solu Comp II is
calibrated taking a measurement of the ozone level in
the process by an independent chemical method and
setting the display equal to the measured value. An
input filter allows the user to configure the analyzer
for rapid response of low noise. The low noise option
is recommended for samples containing less than 0.1
ppm dissolved ozone.

PERFORMANCE SPECIFICATIONS

Measurement Range: 0-10 ppm (mg/L)
Resolution: 0.001 ppm dissolved ozone
Temperature Correction for Membrane Permeability:

Automatic (with Pt100 RTD in sensor) or
manual 0-35°C. Can be disabled if desired.

Input filter: time constant 1 - 999 sec

RECOMMENDED SENSOR

Model 499A OZ Dissolved Ozone Sensor

LOOP SPECIFICATIONS WITH A MODEL

499A OZ SENSOR

Loop Accuracy: ±5% of reading or ± 3 ppb at 25°C,

whichever is greater

Repeatability: ±2% of reading at a constant tempera-

ture

DISSOLVED OZONE (Code -26)

10.34 ppm

29.3 C 12.34mA

10.34 ppm

29.3 C 12.34mA

8

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

1.3 ORDERING INFORMATION

The Solu Comp II analyzers offer the choice of single or dual sensor input with measurement choices of pH/ORP, conductivi-

ty/resistivity, toroidal conductivity, flow, chlorine, dissolved oxygen, and dissolved ozone. See combination guide (on the fol­lowing page) for valid combinations. Standard features include two isolated outputs, three alarm relays, customizable two-line
display, and temperature correction.

MODEL 1055 SOLU COMP II ANALYZER

CODE MEASUREMENT 2 (Optional)

30 Contacting Conductivity
31 Toroidal Conductivity
32 pH/ORP
33 Flow

CODE FIELD-COMMISSIONED SUITES (Optional) see tables below

S1 Suite 1 - Field Commissioned Measurement

(basic)

S1A Suite 1 - Field Commissioned Measurement

(includes amperometric)

S2 Suite 2 - Field Commissioned Measurement

(basic)

S2A Suite 2 - Field Commissioned Measurement

(includes amperometric)

CODE OPTIONAL

68 UL Approval

CODE POWER

01 115/230 Vac, 50/60 Hz
02 24 Vdc

CODE MEASUREMENT 1 (Required Selection)

20 Contacting Conductivity
21 Toroidal Conductivity
22 pH/ORP
23 Flow
24 Chlorine
25 Dissolved Oxygen
26 Ozone

CODE MOUNTING

10 Panel mounting enclosure
11 Pipe/Surface mounting enclosure

(Pipe mounting requires accessory kit PN 23820-00)

MODEL 1055 SOLU COMP II ANALYZER

CODE POWER

01 115/230 Vac, 50/60 Hz
02 24 Vdc

CODE MOUNTING

10 Panel mounting enclosure
11 Pipe/Surface mounting enclosure

(Pipe mounting requires accessory kit PN 23820-00)

CODE OPTIONAL

DM Dual Measurement

CODE OPTIONAL

68 UL Approval

Field Commisssioned Suites option offers the user the ability to commission the Solu Comp II to any valid measurement
combination. This feature provides the benefit of a reduction in the number of spare instruments required to meet emergency
inventory needs. Please refer to the Suites tables (on the following page) for valid measurement combinations. Suites include
a complete set of instrument wiring labels.

9

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

COMBINATION GUIDE

* For D.O. sensors with 22k thermistor,

use Suite 1 only.

10

MODEL SOLU COMP II SECTION 1.0

DESCRIPTION AND SPECIFICATIONS

ACCESSORIES (Weights are rounded up to nearest whole lb or 0.5 kg)

PART NUMBER DESCRIPTION WEIGHT SHIPPING WT.

23820-00 Pipe mounting kit, includes U-bolts, mounting bracket, nuts, 2 lb (1.0 kg) 4 lb (2.0 kg)

washers, and screws (complete)

23554-00 Gland fittings, PG 13.5, 5 per package 1 lb (0.5 kg) 2 lb (1.0 kg)

9240048-00 Tag, stainless steel (specify marking) 1 lb (0.5 kg) 1 lb (0.5 kg)

pH INPUT

9210012 Buffer Solution, 4.01 pH, 16 oz. 1 lb (0.5 kg) 2 lb (1.0 kg)

9210013 Buffer Solution, 6.86 pH, 16 oz. 1 lb (0.5 kg) 2 lb (1.0 kg)

9210014 Buffer Solution, 9.18 pH, 16 oz. 1 lb (0.5 kg) 2 lb (1.0 kg)

CONDUCTIVITY INPUT

SS-1 Conductivity Standard, 1409 µS/cm at 25°C, 1 quart (945 mL) 2 lb (1.0 kg) 4 lb (2.0 kg)

SS-1A Conductivity Standard, 1409 µS/cm at 25°C, 1 gallon (3785 mL) 9 lb (4.0 kg) 11 lb (5.0 kg)

SS-5 Conductivity Standard, 1000 µS/cm at 25°C, 1 quart (945 mL) 2 lb (1.0 kg) 4 lb (2.0 kg)

SS-5A Conductivity Standard, 1000 µS/cm at 25°C, 1 gallon (3785 mL) 9 lb (4.0 kg) 11 lb (5.0 kg)

SS-6 Conductivity Standard, 200 µS/cm at 25°C, 1 quart (945 mL) 2 lb (1.0 kg) 4 lb (2.0 kg)

SS-6A Conductivity Standard, 200 µS/cm at 25°C, 1 gallon (3785 mL) 9 lb (4.0 kg) 11 lb (5.0 kg)

SS-7 Conductivity Standard, 5000 µS/cm at 25°C, 1 quart (945 mL) 2 lb (1.0 kg) 4 lb (2.0 kg)

SS-7A Conductivity Standard, 5000 µS/cm at 25°C, 1 gallon (3785 mL) 9 lb (4.0 kg) 11 lb (5.0 kg)

11

SECTION 2.0.

INSTALLATION

MODEL SOLU COMP II SECTION 2.0

INSTALLATION

2.1 UNPACKING AND INSPECTION

2.2 INSTALLATION

Type of Mounting Section

Panel 2.2.2

Pipe 2.2.3

Surface 2.2.4

2.1 UNPACKING AND INSPECTION

Inspect the shipping container. If it is damaged, contact the shipper immediately for instructions. Save the box. If
there is no apparent damage, unpack the container. Be sure all items shown on the packing list are present. If
items are missing, notify Rosemount Analytical immediately.

2.2 INSTALLATION

2.2.1 General Information

1. Although the analyzer is suitable for outdoor use, do not install it in direct sunlight or in areas of extreme tem­peratures.

2. Install the analyzer in an area where vibrations and electromagnetic and radio frequency interference are min­imized or absent.

3. Keep the analyzer and sensor wiring at least one foot from high voltage conductors. Be sure there is easy
access to the analyzer.

4. AC power and relay wiring should not enter via top conduit openings and should be kept separated
from other wiring in the analyzer after installation.

5. The analyzer is suitable for panel, pipe, or surface mounting. Refer to the table below.

6. See Section 3.1 for removal of conduit knockouts.

7. To reduce the likelihood of stress on wiring connections, the hinged front panel (-11 models) shall not be
removed from the base during wiring installation, and there shall be sufficient wire leads to avoid stress on con­ductors.

8. For UL-approved models (-68), the clear wiring shield must be installed prior to operation.

12

MODEL SOLU COMP II SECTION 2.0

INSTALLATION

FIGURE 2-1. Panel Mount Installation

Access to the wiring terminals is through the rear cover. Four screws hold the cover in place.

2.2.2 Panel Mounting.

MILLIMETER

INCH

MODEL SOLU COMP II SECTION 2.0

INSTALLATION

FIGURE 2-2. Pipe Mount Installation

The front panel is hinged at the bottom. The panel swings down for access to the wiring terminals.

2.2.3 Pipe Mounting.

MILLIMETER

INCH

13

MODEL SOLU COMP II SECTION 2.0

INSTALLATION

14

FIGURE 2-3. Surface Mount Installation

The front panel is hinged at the bottom. The panel swings down for access to the wiring terminals.

2.2.4 Surface Mounting.

MILLIMETER

INCH

15

3.2 POWER, ALARM, OUTPUT, AND SENSOR CONNECTIONS

The Solu Comp II is available in two mounting configurations.The positions of the power, alarm, output, and sen­sor terminal blocks are different in each. Refer to the table to find the correct drawing.

For best EMI/RFI protection use
shielded output signal cable
enclosed in an earth-grounded
metal conduit. Connect the
shield to earth ground at termi­nal 4 on TB1.

AC wiring should be 14 gauge or greater. Provide a switch or breaker to disconnect the analyzer from the main power
supply. Install the switch or breaker near the analyzer and label it as the disconnecting device for the analyzer.

Keep sensor and output signal wiring separate from power wiring. Do not run sensor and power wiring in the same
conduit or close together in a cable tray.

Refer to the sensor manual or wiring sheet to identify the sensor wire colors and functions.

MODEL MOUNTING POWER FIGURE

1055pH-01-10 Panel 115/230 Vac 3-2
1055pH-02-10 24 Vdc 3-3
1055pH-01-11 Surface/Pipe 115/230 Vac 3-4
1055pH-02-11 24 Vdc 3-5

WARNING: RISK OF ELECTRICAL SHOCK

AC connections and grounding must be in compliance
with UL 508 or local electrical code. DO NOT apply
power to the analyzer until all electrical connections are
verified and secure.

SECTION 3.0.

WIRING

3.1 PREPARING CONDUIT OPENINGS

3.2 POWER, ALARM, OUTPUT, AND SENSOR
CONNECTIONS

MODEL SOLU COMP II SECTION 3.0

WIRING

3.1 PREPARING CONDUIT OPENINGS

The number of conduit openings and the location depend on
the model.

Conduit openings accept 1/2-inch conduit fittings or PG 13.5
cable glands. To keep the case watertight, block unused
openings with NEMA 4X or IP65 conduit plugs.

NOTE

Use watertight fittings and hubs that comply with the
requirements of UL514B. Connect the conduit hub to the
conduit before attaching the fitting to the analyzer (UL508-

26.16).

Figure 3-1 shows how to remove the knockouts. The knockout grooves are on the outside of the case. Place the
screwdriver blade on the inside of the case and align it approximately along the groove. Rap the screwdriver sharply
with a hammer until the groove cracks. Move the screwdriver to an uncracked portion of the groove and continue
the process until the knockout falls out. Use a small knife blade to remove the flash from the inside of the hole.

FIGURE 3-1. Removing the Knockouts

Model Description Conduit openings
1055-10 panel mount two open, three knockouts
1055-11 surface or pipe mount three open, no knockouts

16

MODEL SOLU COMP II SECTION 3.0

WIRING

FIGURE 3-2. Wiring Connections for Solu Comp II Model 1055-01-10

(Panel Mount with 115/230 Vac Power)

FIGURE 3-3. Wiring Connections for Solu Comp II Model 1055-02-10

(Panel Mount with 24 Vdc Power)

MODEL SOLU COMP II SECTION 3.0

WIRING

FIGURE 3-5. Wiring Connections for Solu Comp II Model 1055-02-11

(Surface/Pipe Mounting with 24 Vdc Power)

FIGURE 3-4. Wiring Connections for Solu Comp II Model 1055-01-11

(Surface/Pipe Mounting with 115/230 Vac Power)

17

18

MODEL SOLU COMP II SECTION 4.0

DISPLAY AND OPERATION

SECTION 4.0

DISPLAY AND OPERATION

4.1 DISPLAY

4.2 KEYPAD

4.3 PROGRAMMING AND CALIBRATING THE SOLU COMP II - TUTORIAL

4.4 SECURITY

4.5 USING HOLD

4.1. DISPLAY

The Solu Comp II has a two-line display.
The display can be customized to meet
user requirements (see Section 5.11).
Figure 4-1 shows some of the displays
available during normal operation. View
A is the default screen for a single sen­sor. View B is the default screen for dual
sensors.

The Solu Comp II has information
screens that supplement the data in the
main display. Press or to view the
information screens. The last informa-

tion screen is the software version.

During calibration and programming,
key presses cause different displays to
appear. The displays are self-explanato­ry and guide the user step-by-step
through the procedure.

4.2 KEYPAD

Figure 4-2 shows the Solu Comp II key­pad.

FIGURE 4-1. Displays During Normal Operation

Screen A shows pH, temperature, and current output for sensor 1. Screen
B shows pH for sensors 1 and 2. Although screens A and B are the most
useful, other screens can be selected. For example, screen C shows the
pH, temperature, and glass and reference impedance for sensor 1. If
screen C were for sensor 2, S2 would appear in the display. See Section

5.9 for more details.

FIGURE 4-2. Solu Comp II Keypad

Four arrow keys move the cursor around the screen. A blinking word or
numeral show the position of the cursor. The arrow keys are also used to
change the value of a numeral. Pressing ENTER stores numbers and set­tings and moves the display to the next screen. Pressing EXIT returns to
the previous screen without storing changes. Pressing MENU always
causes the main menu screen to appear. Pressing MENU followed by
EXIT causes the main display to appear.

19

MODEL SOLU COMP II SECTION 4.0

DISPLAY AND OPERATION

4.3 PROGRAMMING AND CALIBRATING THE SOLU COMP II

- TUTORIAL

Setting up and calibrating the Solu Comp II is easy. The following tutorial
describes how to move around in the programming menus. For practice, the
tutorial also describes how to assign conductivity values to the 4 and 20 mA
outputs for sensor 1.

1. If the MENU screen (shown at the left) is not already showing, press

MENU. Calibrate is blinking, which means the cursor is on Calibrate.

2. To assign pH values to current outputs, the Program sub-menu must be
open. Press . The cursor moves to Program (Program blinking). Press
ENTER. Pressing ENTER opens the Program sub-menu.

3. The Program sub-menu permits the user to set outputs, alarms, auto­matic or manual temperature compensation, and a security code. When
the sub-menu opens, Outputs is blinking, which means the cursor is on
Outputs. Press or (or any arrow key) to move the cursor around the
display. Move the cursor to >> and press ENTER to cause a second
screen with more program items to appear. There are three screens in the
Program menu. Pressing >> and ENTER in the third screen causes the
display to return to the first screen (Outputs, Alarms, Measurement).

4. For practice, assign pH values to the 4 and 20 mA outputs for sensor 1.
Move the cursor to Outputs and press ENTER.

5. The screen shown at left appears. The cursor is on Output Range (blink­ing). Output range is used to assign values to the low and high current
outputs. Press ENTER.

6. The screen shown at left appears. The Solu Comp II has two outputs, out­put 1 and output 2. Move the cursor to the desired output and press
ENTER. For purposes of the example, choose Output 1.

7. The screen shown at left appears. Out1 S1 in the top line means output
1 (Out1) is assigned to sensor 1 (S1). Either output can be assigned to
either sensor (sensor and output assignments are made under the
Output Configure menu shown in step 5). Use the Out1 S1 Range?
screen to assign a pH value to the 4 mA output.

a. Use the arrow keys to change the pH to the desired value. Press

or to move the cursor from digit to digit. Press or to increase
or decrease the value of the digit. Holding or down causes the
numeral to continuously scroll up or down.

b. To move the decimal point, press or until the cursor is on the

decimal point. Press to move the decimal point to the right. Press

to move the decimal point to the left.

c. Press ENTER to store the setting.

8. The screen shown at left appears. Use this screen to assign a full scale
pH value to the 20 mA output. Use the arrow keys to change the pH to
the desired value. Press ENTER to store the setting.

9. The screen shown at left appears. To assign pH values to the low and
high currents for output 2, select Output 2 and follow the prompts.

10. To return to the main menu, press MENU. To return to the main display
press MENU then EXIT, or press EXIT repeatedly until the main display
appears. To return to the previous display press EXIT.

NOTE

To store values or settings, press ENTER before pressing EXIT.

CCaalliibbrraattee

Hold

Program Display

Calibrate Hold

PPrrooggrraamm

Display

OOuuttppuuttss

Alarms

Measurement >>

OOuuttppuutt RRaannggee

Output Configure

Output Range?

OOuuttppuutt11

Output2

Out1 S1 Range?

4mA

00

.00pH

Out1 S1 Range?

20mA

11

4.00pH

Output Range?

OOuuttppuutt11

Output2

MODEL SOLU COMP II SECTION 4.0

DISPLAY AND OPERATION

1. If a security code has been programmed, pressing MENU causes the
security screen to appear.

2. Enter the three-digit security code.

3. If the entry is correct, the main menu screen appears. If the entry is incor­rect, the Invalid Code screen appears. The Enter Security Code screen
reappears after 2 seconds.

Enter Security

Code

000000

Invalid Code

Calibrate

HHoolldd

Program Display

Hold Outputs and

Alarms?

YYeess

No

20

4.4 SECURITY

4.4.1 How the Security Code Works

Use the security code to prevent accidental or unwanted changes to program settings, displays, and calibration.

4.4.2 Bypassing the Security Code

Enter 555. The main menu will open.

4.4.3 Setting a Security Code

See Section 5.6.

4.5 USING HOLD

4.5.1 Purpose

The analyzer output is always proportional to measured pH. To prevent unwanted alarms and improper operation
of control systems or dosing pumps, place the analyzer in hold before removing the sensor for calibration and

maintenance. Be sure to remove the analyzer from hold once calibration is
complete. During hold, both outputs remain at the last value. Once in hold, the
analyzer remains there indefinitely. While in hold, the screen shown to the
left appears periodically.

HHoolldd

4.5.2 Using the Hold Function

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Hold.

2. The Hold Outputs and Alarms ? screen appears. Choose Yes to place
the analyzer in hold. Choose No to take the analyzer out of hold.

3. The main display screen will appear.

21

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

SECTION 5.0

PROGRAMMING THE ANALYZER

5.1 GENERAL

5.2 CHANGING STARTUP SETTINGS

5.3 CONFIGURING AND RANGING THE OUTPUTS

5.4 CONFIGURING ALARMS AND ASSIGNING SETPOINTS

5.5 SELECTING THE TYPE OF MEASUREMENT AND ACTIVATING SOLUTION
TEMPERATURE CORRECTION

5.6 CHOOSING TEMPERATURE UNITS AND MANUAL OR AUTOMATIC TEM­PERATURE COMPENSATION

5.7 SETTING A SECURITY CODE

5.8 NOISE REJECTION

5.9 SINGLE SENSOR OR DUAL SENSOR INPUT

5.10 RESETTING FACTORY DEFAULT SETTINGS

5.11 SELECTING A DEFAULT SCREEN, LANGUAGE, AND SCREEN CONTRAST

5.1 GENERAL

This section describes how to do the following:

1. configure and assign values to the current outputs

2. configure and assign setpoints to the alarm relays

3. choose pH, ORP, or redox

4. choose temperature units and manual or automatic temperature compensation

5. set a security code

6. tell the analyzer the frequency of the ac power (needed for optimum noise rejection)

7. tell the analyzer the number of sensors being used

8. reset the analyzer to factory calibration and default settings

9. select a default display screen

Default settings are shown in Table 5-1 on the following page. To change a default setting, refer to the section list­ed in the table. To reset default settings, see Section 5.10.

5.2 CHANGING STARTUP SETTINGS

When the Solu Comp II is powered up for the first time, startup screens appear. The screens prompt the user to
identify the number of sensors being used and whether pH, ORP, or redox is being measured. If incorrect settings
were entered at startup, enter the correct settings now. To change the number of sensors refer to Section 5.9. To
change the measurement, refer to Section 5.5.

FOR BEST RESULTS, ENTER THE NUMBER OF SENSORS BEING USED
(SECTION 5.9) AND WHETHER pH, ORP, OR REDOX IS BEING MEASURED
(SECTION 5.5) BEFORE MAKING OTHER PROGRAM SETTINGS.

22

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

TABLE 5-1. DEFAULT SETTINGS

1. SENSOR-OUTPUT ASSIGNMENTS (pH, ORP, or redox is selected during Quick Start)

6. MISCELLANEOUS SETTINGS

Section

Language English 5.11

Hold off 4.5

Security code 000 (no security code) 5.7

ac power frequency 60 Hz 5.8

5. TEMPERATURE RELATED SETTINGS

Section

Units °C 5.6

Automatic temperature compensation On 5.6

Solution temperature correction Off 5.5

Isopotential pH 7.00 5.5

3. OUTPUT RANGES (pH, ORP, or redox is selected during Quick Start)

Measurement Range Section

pH 0 to 14 5.3

ORP/Redox -1400 to 1400 mV 5.3

Temperature 0 to 100°C 5.3

Sensor(s) Output 1 Output 2 Section

Single sensor pH/ORP/Redox Temperature 5.3 and 5.9

Dual sensor pH/ORP/Redox for sensor 1 pH/ORP/Redox for sensor 2 5.3 and 5.9

2. OTHER OUTPUT SETTINGS

Output Dampening 0 or 4 mA Mode Section

1 off 4 linear 5.3

2 off 4 linear 5.3

4. ALARM CONFIGURATION AND SETPOINTS

Alarm

1 2 3 Section

Assigned to Sensor 1 Sensor 1 (note) Fault 5.4

High or low High High NA 5.4

Deadband 0 0 NA 5.4

Setpoint (pH) 14 (high); 0 (low) 14 (high); 0 (low) NA 5.4

Setpoint (ORP/Redox) 1400 mV (high); -1400 mV (low) 1400 mV (high); -1400 mV (low) NA 5.4

Note: For dual sensor input, alarm 2 is assigned to sensor 2.

23

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.3 CONFIGURING AND RANGING THE OUTPUTS.

5.3.1 Purpose

The Solu Comp II accepts inputs from two pH or ORP sensors and has two current outputs. This section describes
how to configure and range the outputs. CONFIGURE THE OUTPUTS FIRST.

1. Configuring an output means

a. Selecting either a 4-20 mA or 0-20 mA output,

b. Assigning a sensor and a measurement (pH, ORP, or redox potential) to output 1 and output 2,

c. Turning on or turning off output current dampening.

d. Choosing a linear or logarithmic output.

2. Ranging the outputs means assigning values to the low (0 or 4 mA) and high (20 mA) outputs.

5.3.2 Definitions

1. CURRENT OUTPUTS. The analyzer provides either a continuous 4-20 mA or 0-20 mA output current directly
proportional to pH, ORP, redox potential, or temperature. The low and high current outputs can be set to any
value in the table.

Measurement Range Recommended Range

pH 0 to 14 NA

ORP/Redox -2000 to 2000 mV NA

Temperature -99 to 999°C or °F -5 to 200°C

2. ASSIGNING OUTPUTS. Figure 5-1 shows the ways in which the outputs can be assigned.

3. DAMPEN. Output dampening smooths out noisy readings. It also increases the response time of the output.
With output dampening the time to reach 63% of final reading following a step change is 5 sec. Output damp­ening does not affect the response time of the display.

4. MODE. The current output can be made directly proportional to the displayed value (linear mode) or directly
proportional to the common logarithm of the displayed value (log mode).

FIGURE 5-1. Assigning Outputs 1 and 2

24

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.3.3. Procedure: Configure Outputs.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose Outputs.

3. Choose Output Configure.

4. Choose Output1 or Output2.

5. Choose Sensor1 or Sensor2. Either sensor can be assigned to either

output.

6. Choose Measurement or Temp . The output will be pH (or Redox or
ORP) if Measurement is selected or the temperature if Temp is select-
ed.

7. Make the appropriate settings:

a. Choose 4-20 mA or 0-20 mA.

b. Choose Yes or No for output dampening.

c. Choose Linear or Log output.

8. The display returns to the Output Config? screen. Select the other out­put or press EXIT to return to the previous screen. To return to the main
display, press MENU followed by EXIT.

5.3.4. Procedure: Assigning Values to the Low and High Current Outputs (Output Ranging)

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose Outputs.

3. Choose Output Range. Choose Output1 or Output2.

4. Make the appropriate settings.

a. Assign a value to the low current (0 mA or 4 mA) output.

b. Assign a value to the high current (20 mA) output.

5. The display returns to the Output Range screen. Select the other output
or press EXIT to return to the previous screen. To return to the main dis­play, press MENU followed by EXIT.

Calibrate Hold

PPrrooggrraamm

Display

Output Config?

OOuuttppuutt11

Output2

OutM is for?

SSeennssoorr11

Sensor2

OutM is for?

MMeeaassuurreemmeenntt

Temp

Output Range

OOuuttppuutt CCoonnffiigguurree

OOuuttppuuttss

Alarms

Measurement >>

Calibrate Hold

PPrrooggrraamm

Display

OOuuttppuutt RRaannggee

Output Configure

OOuuttppuuttss

Alarms

Measurement >>

25

Alarm relays are single pole-double throw (SPDT). When an alarm is activated, the coil is energized.

When an alarm activates, AL1, AL2, or AL3 (as appropriate) appears periodically in the display.

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.4 CONFIGURING ALARMS AND ASSIGNING SETPOINTS

5.4.1 Purpose

This section describes how to do the following:

1. assign an alarm relay to a sensor,

2. set the alarm logic to high or low,

3. assign values to the alarm setpoints,

4. set the alarm deadbands.

ALARM RELAYS MUST BE CONFIGURED BEFORE ASSIGNING SETPOINTS.

5.4.2 Definitions

1. ASSIGNING ALARMS. There are three alarms (AL1, AL2, and AL3). Alarms 1 and 2 can be assigned to any
sensor. For example, AL1 and AL2 can be assigned to sensor 1 with, perhaps, one alarm configured as a high
alarm and the other as a low alarm, and AL3 can be assigned to sensor 2. Alarms are for pH, ORP, redox, or
temperature. Alarm 3 can be assigned to either sensor or used as a fault alarm. The fault alarm activates when
a fault exists in a sensor or the analyzer.

2. FAULT ALARM. A fault condition exists when the Solu Comp II detects a problem with a sensor or with the ana­lyzer that is likely to cause seriously erroneous readings. If Alarm 3 was programmed as a fault alarm, the
alarm 3 relay will activate. The word Fault will appear alternately in the display with the reading.

3. ALARM LOGIC, SETPOINTS, AND DEADBANDS. See Figures 5-2 and 5-3.

FIGURE 5-2. High Alarm Logic

The alarm activates when the pH exceeds the high
setpoint. The alarm remains activated until the reading
drops below the value determined by the deadband.

FIGURE 5-3. Low Alarm Logic

The alarm activates when the pH drops below the low
setpoint. The alarm remains activated until the reading
increases above the value determined by the deadband.

26

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.4.3 Procedure: Configuring Alarms

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose Alarms.

3. Choose Alarm Configure.

4. Choose Alarm 1 (AL1), Alarm 2 (AL2), or Alarm 3 (AL3).

5. For AL1 or AL2

a. Choose Sensor 1 or Sensor 2. For a single input configuration, the

Sensor 1 Sensor 2 screen does not appear.

b. Choose Measurement or Temp.

c. Choose High or Low.

d. Set the alarm Deadband.

6. The display returns to the Alarm Configure? screen. Select another

alarm or press EXIT to return to the previous screen. To return to the main
display, press MENU followed by EXIT.

7. For AL3

a. Choose Sensor1, Sensor2, or Fault.

b. For Sensor1, select High or Low and set the deadband.

c. Choosing Fault means AL3 will activate when a sensor or analyzer

fault exists. There is no user setting to make.

8. The display returns to the Alarm Configure? screen. Select another

alarm or press EXIT to return to the previous screen. To return to the main
display, press MENU followed by EXIT.

Calibrate Hold

PPrrooggrraamm

Display

Alarm Setpoints

AAllaarrmm CCoonnffiigguurree

Alarm Config?

AALL11

AL2 AL3

AL1 is for?

SSeennssoorr11

Sensor2

AL1 S1 is for?

MMeeaassuurreemmeenntt

Temp

Outputs

AAllaarrmmss

Measurement >>

AL3 is for?

FFaauulltt

Sensor1 Sensor2

27

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.4.4 Procedure: Programming Alarm Setpoints

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose Alarms.

3. Choose Alarm Setpoints.

4. Choose Alarm 1 (AL1), Alarm 2 (AL2), or Alarm 3 (AL3).

5. The display shows the alarm selected (AL1) and the configuration. The
alarm is for Sensor 1 (S1), and the logic is high. Use the arrow keys to
change the alarm setpoint.

6. The display returns to the Select Alarm? screen. Select another alarm or
press EXIT to return to the previous screen. To return to the main display,
press MENU followed by EXIT.

Calibrate Hold

PPrrooggrraamm

Display

AAllaarrmm SSeettppooiinnttss

Alarm Configure

Select Alarm?

AALL11

AL2 AL3

AL1 S1 Setpoint?

High

11

4.00pH

Outputs

AAllaarrmmss

Measurement >>

28

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.5 SELECTING THE TYPE OF MEASUREMENT AND ACTIVATING SOLUTION
TEMPERATURE CORRECTION

5.5.1 Purpose

This section describes how to do the following:

1. Program the Solu Comp II to measure pH, ORP, or redox potential.

2. Select a solution temperature correction.

3. Change the analyzer isopotential point.

5.5.2 Definitions

1. ORP. ORP is oxidation-reduction potential. It is the voltage difference between a noble metal (usually plat-

inum) indicator electrode and a silver/silver chloride reference electrode.

2. REDOX. Redox is redox potential. Redox potential is measured the same way as ORP. The sign of the redox

potential is the negative of ORP.

2. SIGN CONVENTION. The ORP of a solution of 0.1 M iron (II) ammonium sulfate and 0.1 M iron (III) ammoni-

um sulfate in 1 M sulfuric acid is positive. The redox potential is negative.

4. SOLUTION TEMPERATURE CORRECTION. The pH of a solution, particularly an alkaline one, is a function

of temperature. If the temperature changes, so does the pH, even though the concentration of the acid or base
causing the pH remains constant. Solution temperature compensation converts the pH at the measurement
temperature to the pH at a reference temperature. The Solu Comp II corrects the pH to a reference tempera­ture of 25°C.

For an accurate solution temperature correction, the exact composition of the solution must be known. The
Solu Comp II has built-in temperature corrections for high purity water and for dilute solutions of a strong base.
The analyzer also accepts a custom correction.

5. CUSTOM TEMPERATURE CORRECTION. The custom temperature correction has units of ∆pH/°C. The

example shows how the analyzer uses the custom correction. Suppose the pH of the solution being measured
decreases 0.022 units for every Celsius degree rise in temperature. The temperature correction is

-0.022pH/°C. If the pH at 20°C is 8.95, the corrected pH (at 25°C) is 8.95 + (-0.022)(25 - 20) or 8.84.

6. ISOPOTENTIAL pH. The isopotential pH is the pH at which the cell voltage (the cell is the pH electrode, ref-

erence electrode, and solution being measured) is independent of temperature. Most pH cells have isopoten­tial pH reasonably close to 7.00, so the Solu Comp II assumes the cell isopotential pH is 7.00. However, cer­tain specialized electrodes have isopotential pH different from 7.00.

NOTE

Do NOT change the isopotential pH of the transmitter unless you are thoroughly
familiar with the role of sensor and analyzer isopotential point in pH measure­ment, OR the sensor operating instructions specifically state the isopotential pH
is a value other than pH 7.00.

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.5.3 Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

29

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose Measurement.

3. Choose Sensor 1 or Sensor 2. For a single input configuration, the
Sensor 1 Sensor 2 screen does not appear.

4. Choose pH, Redox, or ORP.

If you chose pH, do steps 5 through 9.

If you chose ORP or Redox, do step 10.

5. Choose No if a non-glass pH sensing electrode is being used.

6. Choose Soln Temp Corr or Sensor Isoptntl.

7. For Soln Temp Corr, choose Off, UltraPure, HighpH, or Custom. For
Custom, enter the desired temperature coefficient.

8. For Sensor Isoptntl, enter the desired sensor isopotential pH. Do not
change the sensor isopotential pH unless the sensor is known to have an
isopotential pH different from 7.00.

9. The display returns to the screen shown in step 3. Choose Sensor 2
(conductivity) and follow the prompts.

10. If Redox or ORP was selected, there are no further settings to make. The
display returns to the screen shown in step 3. Choose Sensor 2 (con­ductivity) and follow the prompts.

11. The display returns to the screen shown in step 3. Press EXIT to return to
the previous screen. To return to the main display, press MENU followed
by EXIT.

12. If TDS was selected, there are no further settings to make.The display
returns to the screen shown in step 3. Press EXIT to return to the previ­ous screen. To return to the main display, press MENU followed by EXIT.

Calibrate Hold

PPrrooggrraamm

Display

Config?

SSeennssoorr11

Sensor2

S1Measure?

ppHH

Redox ORP

S1 SolnTempCorr?

OOffff

Ultrapure >>

Sensor Isoptntl

S1:

00

7.00pH

S1 Glass Fault

Enable? Yes

NNoo

Outputs Alarms

MMeeaassuurreemmeenntt

>>

SSoollnn TTeemmpp CCoorrrr

Sensor Isoptntl

30

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.6.3 Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose >>.

3. Choose Temp.

4. Choose °C/F to change temperature units. Choose Live/Manual to turn
on (Live) or turn off (Manual) automatic temperature compensation.

a. If °C/F is chosen, select °C or °F in the next screen.
b. If Live/Manual is chosen, select Live or Manual for sensor 1 in the

next screen.

c. If Manual is chosen, enter the temperature in the next screen. The

temperature entered in this step will be used in all subsequent meas­urements, no matter what the process temperature is.

d. The display will return to the Live/Manual screen for sensor 2. Make

the desired selections for sensor 2.

Calibrate Hold

PPrrooggrraamm

Display

Config Temp?

°

CC//FF

Live/Manual

TTeemmpp

Security

#Sensors >>

Outputs Alarms

Measurement

>>>>

5.6 CHOOSING TEMPERATURE UNITS AND MANUAL OR AUTOMATIC TEMPERATURE
COMPENSATION

5.6.1 Purpose

This section describes how to do the following:

1. Choose temperature display units (°C or °F).

2. Choose automatic or manual temperature compensation.

3. Enter a temperature for manual temperature compensation

5.6.2 Definitions

1. AUTOMATIC TEMPERATURE COMPENSATION. The analyzer uses a temperature-dependent factor to con-

vert measured cell voltage to pH. In automatic temperature compensation, the analyzer measures the tem­perature and automatically calculates the correct conversion factor. For maximum accuracy, use automatic
temperature compensation.

2. MANUAL TEMPERATURE COMPENSATION. In manual temperature compensation, the analyzer converts

measured voltage to pH using the temperature entered by the user. It does not use the actual process tem­perature. Do NOT use manual temperature compensation unless the process temperature varies no more than
about ±2°C or the pH is between 6 and 8. Manual temperature compensation is useful if the sensor tempera­ture element has failed and a replacement sensor is not available. If manual temperature correction is select­ed, the display will not show the measured temperature. It will show the manually entered value.

31

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.8 NOISE REJECTION

5.8.1 Purpose.

For maximum noise rejection, the frequency of the ac power must be entered in the analyzer.

5.8.2. Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose >>.

3. Choose >>.

4. Choose Noise Rejection.

5. Enter the mains frequency, 50 Hz or 60 Hz.

6. The display returns to the Noise Rejection screen. To return to the main

menu, press EXIT. To return to the main display, press MENU followed by
EXIT.

Calibrate Hold

PPrrooggrraamm

Display

NNooiissee RReejjeeccttiioonn

ResetAnalyzer >>

OOuuttppuuttss

Alarms

Measurement >>

TTeemmpp

Security

#Sensors >>

5.7 SETTING A SECURITY CODE

5.7.1 Purpose.

This section describes how to set a security code. The security code prevents program and calibration settings
from accidentally being changed. Refer to Section 4.4 for additional information.

5.7.2 Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose >>, then Security.

3. Enter a three digit security code. The security code takes effect two min­utes after the last key stroke.

4. The display returns to the security menu screen. Press EXIT to return to
the previous screen. To return to the main display, press MENU followed
by EXIT.

Calibrate Hold

PPrrooggrraamm

Display

Temp

SSeeccuurriittyy

#Sensors >>

Outputs Alarms

Measurement

>>>>

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.10 RESETTING FACTORY DEFAULT SETTINGS

5.10.1 Purpose.

This section describes how to re-install factory default values. The process also clears all fault messages and
returns the display to the first quick start screen.

5.10.2. Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose >>.

3. Choose >>.

4. Choose ResetAnalyzer.

5.

Choose Yes or No. If Yes is selected, previous settings are cleared and
the Quick Start Menu appears.

Noise Rejection

ResetAnalyzer >>

Load factory

settings?

YYeess

No

OOuuttppuuttss

Alarms

Measurement >>

TTeemmpp

Security

#Sensors >>

Calibrate Hold

PPrrooggrraamm

Display

32

5.9 SINGLE SENSOR OR DUAL SENSOR INPUT

5.9.1 Purpose

The Solu Comp II accepts input from a single sensor or from two sensors. This section describes how to program
the analyzer for single or dual sensors. COMPLETE THIS SECTION BEFORE DOING OTHER PROGRAMMING.

5.9.2 Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

1. Press MENU. The main menu screen appears. Choose Program.

2. Choose >>.

3. Choose #Sensors.

4. Choose One or Tw o. Changing from Two to One will cause some set­tings to change.

NOTE

If One sensor is selected, only

S1 will be available. S2 cannot be

disabled.

5. The display returns to the # Sensors screen. To return to the main menu,
press MENU. To return to the main display, press MENU followed by
EXIT.

# of sensors?

One

ΤΤωωοο

OOuuttppuuttss

Alarms

Measurement >>

TTeemmpp

Security

#Sensors >>

Calibrate Hold

PPrrooggrraamm

Display

33

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.11.2 Procedure: Selecting a Display Screen

1. Press MENU. The main menu screen appears. Choose Display.

2. Choose Default Display.

3. Press or until the desired display appears. Press ENTER. For an
explanation of abbreviations, see Section 5.11.1.

4. The display returns to the screen in step 2. To return to the main menu,
press MENU. To return to the main display, press MENU followed by
EXIT.

Calibrate Hold

Program

DDiissppllaayy

DDeeffaauulltt DDiissppllaayy

Language Contrst

5.11.3 Procedure: Choosing a Language

1. Press MENU. The main menu screen appears. Choose Display.

2. Choose Language.

3. Choose English, Français, Español, Deutsch, Italiano, or Portugues.

4. The display returns to the screen in step 2. To return to the main menu,
press MENU. To return to the main display, press MENU followed by
EXIT.

Calibrate Hold

Program

DDiissppllaayy

Default Display

LLaanngguuaaggee

Contrast

EEnngglliisshh

Fran ais

Espa ol >>

5.11 SELECTING A DEFAULT SCREEN, LANGUAGE, AND SCREEN CONTRAST

5.11.1 Purpose

This section describes how to do the following:

1. set a default display screen

The default display screen is the screen shown during normal operation. The Solu Comp II allows the user to
choose from a large number of screens. Which screens are available depends on how the analyzer was con­figured. The following is an explanation of the abbreviations used in the screens.

In the display:

i. S means sensor. S1 is sensor 1, and S2 is sensor 2. If neither S1 nor S2 appears, then the analyzer has

been configured for a single sensor input.

ii. G is glass electrode impedance, and R is reference electrode impedance.

2. select a language

3. change the screen contrast

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

MODEL SOLU COMP II SECTION 5.0

PROGRAMMING THE ANALYZER

5.11.2 Procedure: Changing Screen Contrast

1. Press MENU. The main menu screen appears. Choose Display.

2. Choose Contrst.

3. Press or to increase or decrease the screen contrast. As contrast
increases, the number increases.

4. The display returns to the screen shown in step 2. To return to the main
menu, press MENU. To return to the main display, press MENU followed
by EXIT.

Calibrate Hold

Program

DDiissppllaayy

Default Display

Units

CCoonnttrrsstt

Screen Contrast:

5500

34

35

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

SECTION 6.0

CALIBRATION

6.1 INTRODUCTION

6.2 CALIBRATING TEMPERATURE

6.3 TWO-POINT BUFFER CALIBRATION (AUTO CALIBRATION)

6.4 TWO-POINT BUFFER CALIBRATION (MANUAL CALIBRATION)

6.5 MAKING THE ANALYZER READING MATCH A SECOND
INSTRUMENT (STANDARDIZATION)

6.6 ENTERING A KNOWN SLOPE

6.7 ORP CALIBRATION

6.1 INTRODUCTION

The Calibrate Menu allows the user to calibrate the pH, ORP (or redox), and temperature response of the sensor.

For pH sensors, two-point buffer calibration is standard. In auto calibration the Solu Comp II calculates the actual
pH of the buffer from the nominal value entered by the user and does not accept calibration data until readings are
stable. In manual calibration the user enters buffer values and judges when readings are stable. The pH reading
can also be standardized, that is, forced to match the reading from a referee instrument. Finally, if the user knows
the electrode slope (at 25°C), he can enter it directly.

The ORP calibration is a single-point calibration against an ORP standard.

6.2 CALIBRATING TEMPERATURE

6.2.1 Purpose

Temperature affects the measurement of pH in three ways.

1. The analyzer uses a temperature dependent factor to convert measured cell voltage to pH. Normally, a slight
inaccuracy in the temperature reading is unimportant unless the pH reading is significantly different from 7.00.
Even then, the error is small. For example, at pH 12 and 25°C, a 1°C error produces a pH error less than ±0.02.

2. During auto calibration, the Solu Comp II recognizes the buffer being used and calculates the actual pH of the
buffer at the measured temperature. Because the pH of most buffers changes only slightly with temperature,
reasonable errors in temperature do not produce large errors in the buffer pH. For example, a 1°C error caus­es at most an error of ±0.03 in the calculated buffer pH.

3. The Solu Comp II can be programmed to calculate and display pH at a reference temperature (25°C). The
maximum change in solution pH with temperature is about ±0.04 pH/°C, so a 1°C temperature error does intro­duce a small error. However, the major source of error in solution temperature compensation is using an incor­rect temperature coefficient.

Temperature affects the measurement of ORP in a complicated fashion that is best determined empirically.

Without calibration the accuracy of the temperature measurement is about ±0.4°C. Calibrate the sensor/analyzer
combination if

1. ±0.4°C accuracy is not acceptable

2. the temperature measurement is suspected of being in error. Calibrate temperature by making the analyzer
reading match the temperature measured with a standard thermometer.

6.2.2 Procedure

1. Remove the sensor from the process. Place it in an insulated container of water along with a calibrated ther­mometer. Submerge at least the bottom two inches of the sensor. Stir continuously.

2. Allow the sensor to reach thermal equilibrium. For some sensors, the time constant for a change in tempera­ture is 5 min., so it may take as long as 30 min. for temperature equilibration.

3. If the sensor cannot be removed from the process, measure the temperature of a flowing sample taken from
a point as close to the sensor as possible. Let the sample continuously overflow an insulated container hold­ing a calibrated thermometer.

4. Change the Solu Comp II display to match the calibrated thermometer using the procedure below.

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

a. Press MENU. The main menu screen appears. Choose Calibrate.

b. Choose Sensor1 or Sensor2. For a single input configuration, the

Sensor1 Sensor2 screen does not appear.

c. Choose Temp.

d. If the analyzer was programmed in Section 5.6 to use the actual process

temperature, the screen at left will appear. To calibrate the temperature,
change the number in the second line to match the temperature meas­ured with the standard thermometer. Press ENTER. The display
changes to the screen in step f.

If the analyzer was programmed to use a temperature entered by the
user, the screen shown in step e will appear.

e. If the analyzer was programmed in Section 5.6 to use the temperature

entered by the user, the screen at left will appear. Change the tempera­ture to the desired value, then press ENTER. The analyzer will use the
temperature entered in this step in all measurements and calculations, no
matter what the true temperature is.

f. The screen at left will appear. Press EXIT.

g. Choose the other sensor and enter the temperature.

h. To return to the main display, press MENU followed by EXIT.

CCaalliibbrraattee

Hold

Program Display

CalSensor1?

Measurement

TTeemmpp

CalSensor1?

Measurement

TTeemmpp

Calibrate?

Sensor1

SSeennssoorr22

Calibrate?

SSeennssoorr11

Sensor2

Live 25.0°C

CalS1

++

25.0°C

ManualTemp?

S1: +25.0°C

36

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

6.3 TWO-POINT BUFFER CALIBRATION (AUTO CALIBRATION)

6.3.1 Purpose

1. New sensors must be calibrated before use. Regular recalibration is also necessary.

2. Use auto calibration instead of manual calibration. Auto calibration avoids common pitfalls and reduces errors.

6.3.2 Definitions

1. AUTO CALIBRATION. The analyzer recognizes the buffers and uses temperature-corrected pH values in the
calibration. The table lists the buffers the Solu Comp II recognizes.

Note 1: NIST is National Institute of Standards, DIN is Deutsche Institute für
Normung, JSI is Japan Standards Institute, and BSI is British Standards
Institute.

Note 2: pH 7 buffer is not a standard buffer. It is a popular commercial buffer
in the United States.

The Solu Comp II also measures noise and drift and does not accept calibration data until readings are sta­ble. Calibration data will be accepted as soon as the pH reading is constant to within 0.02 units for 10 sec­onds. The stability settings cannot be changed.

2. SLOPE AND OFFSET. Once the Solu Comp II suc­cessfully completes the calibration, it calculates and
displays the calibration slope and offset. The slope is
reported as the slope at 25°C. Figure 6-1 defines the
terms.

6.3.3 Procedure

1. Obtain two buffer solutions. Ideally the buffer pH val­ues should bracket the range of pH values to be meas­ured.

2. Remove the sensor from the process liquid. If the
process and buffer temperatures are appreciably dif­ferent, place the sensor in a container of tap water at
the buffer temperature. Do not start the calibration until
the sensor has reached the buffer temperature. Thirty
minutes is usually adequate.

3. Calibrate the sensor by using the procedure on the following page.

pH at 25°C Standard(s)

(nominal pH)

1.68 NIST, DIN 19266, JSI 8802, BSI (see note 1)

3.56 NIST, BSI

3.78 NIST

4.01 NIST, DIN 19266, JSI 8802, BSI

6.86 NIST, DIN 19266, JSI 8802, BSI

7.00 (see note 2)

7.41 NIST

9.18 NIST, DIN 19266, JSI 8802, BSI

10.01 NIST, JSI 8802, BSI

12.45 NIST, DIN 19266

FIGURE 6-1. Calibration Slope and Offset

37

38

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

a. Press MENU. The main menu screen appears. Choose Calibrate.

b. Choose Sensor 1 or Sensor 2. For a single input configuration, the

Sensor1 Sensor2 screen does not appear.

c. Choose Measurement.

d. Choose BufferCal.

e. Choose Auto.

f. Rinse the sensor with water and place it in buffer 1. Be sure the glass bulb

and reference junction are completely submerged. Swirl the sensor.

g. Choose Buffer1.

h. The screen at left is displayed until the reading is stable (<0.02 pH change

in 10 sec). When the reading is stable, the screen in step i appears. To
bypass automatic stabilization, press ENTER at any time.

i. The top line shows the actual reading (S1Live). The analyzer also identifies

the buffer and displays the nominal buffer value (buffer pH at 25°C). If the
displayed value is not correct, press or to select the correct value. The
nominal value will change, for example, from 7.01 pH to 6.86 pH. Press
ENTER.

j. The screen shown at left appears.

k. Remove the sensor from buffer 1, rinse it with water, and place it in buffer

2. Swirl the sensor. Choose Buffer2.

l. The screen at left is displayed until the reading is stable (<0.02 pH change

in 10 sec). When the reading is stable, the screen in step m appears. To
bypass automatic stabilization, press ENTER at any time.

m. The top line shows the actual reading (S1Live). The analyzer also identifies

the buffer and displays the nominal buffer value (buffer pH at 25°C). If the
displayed value is not correct, press or to select the correct value. The
nominal value will change, for example, from 7.01 pH to 6.86 pH. Press
ENTER to accept the nominal value.

n. If the calibration was successful, the analyzer will display the offset and

slope (at 25°C).

o. If the calibration was successful and if two sensors are wired to the analyz-

er, the Calibrate? screen appears. Choose the other sensor and repeat
steps d through m.

p. If the slope is out of range (less than 45 mV/pH or greater than 60 mV/pH),

an error screen appears. The display then returns to step f. Repeat the cal­ibration.

q. To return to the main display, press MENU followed by EXIT.

CCaalliibbrraattee

Hold

Program Display

Calibrate?

SSeennssoorr11

Sensor2

Calibrate?

SSeennssoorr11

Sensor2

CalSensor1?

MMeeaassuurreemmeenntt

Temp

S1BufferCal?

AAuuttoo

Manual

S1AutoCal?

BBuuffffeerr11

Buffer2

S1AutoCal?

BBuuffffeerr11

Buffer2

S1 Standardize

Slope

BBuuffffeerrCCaall

S1Live 7.00pH

AutoBuf1

WWaaiitt

S1Live 7.00pH

AutoBuf1

77..0011ppHH

S1Live 7.00pH

Buf2

WWaaiitt

S1Live 7.00pH

AutoBuf2

77..0011ppHH

S1Offset 6mV

Slope 59.16 25

°C

Calibration

Error

S1AutoCal?

Buffer1

BBuuffffeerr22

39

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

6.4 TWO-POINT BUFFER CALIBRATION (MANUAL CALIBRATION)

6.4.1 Purpose

1. New sensors must be calibrated before use. Regular recalibration is also necessary.

2. Use manual calibration if non-standard buffers are being used; otherwise, use auto calibration. Auto calibra­tion avoids common pitfalls and reduces errors.

6.4.2 Definitions

1. MANUAL CALIBRATION. In auto calibration the analyzer recognizes the buffer and uses the temperature-cor­rected pH value in the calibration. The analyzer also measures noise and drift and does not accept calibration
data until readings are stable. During manual calibration, the user must judge when readings are stable and
look up and enter the buffer values.

2. SLOPE AND OFFSET. Once the Solu Comp II successfully completes the calibration, it calculates and dis­plays the calibration slope and offset. The slope is reported as the slope at 25ºC. Figure 6-1 defines the terms.

6.4.3 Procedure

1. Obtain two buffer solutions. Ideally, the buffer pHs should bracket the range of pH values to be measured. Also
obtain a thermometer. The pH of most buffer solutions is a function of temperature. To calibrate the sensor
properly, the pH of the buffer at the measurement temperature must be entered in the analyzer.

2. Remove the sensor from the process liquid. If the process and buffer temperature are appreciably different,
place the sensor in a container of tap water at the buffer temperature. Do not start the calibration until the sen­sor has reached the buffer temperature. Thirty minutes is usually adequate.

3. Calibrate the sensor using the procedure on the following page.

40

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

a. Press MENU. The main menu screen appears. Choose Calibrate.

b. Choose Sensor 1 or Sensor 2. For a single input configuration, the

Sensor1 Sensor2 screen does not appear.

c. Choose Measurement.

d. Choose BufferCal.

e. Choose Manual.

f. Choose Buffer1.

g. Rinse the sensor with water and place it in buffer 1. Be sure the glass bulb

and junction are completely submerged. Swirl the sensor. Also place a
thermometer in the buffer. Press ENTER

h. The top line shows the actual buffer reading (S1 Live). Wait until the read-

ing is stable, then note the temperature. Change the pH in the second line
to the pH of the buffer at the measured temperature. Press ENTER.

i. The screen at left appears. Choose Buffer2. Rinse the sensor and ther-

mometer with water and place them in buffer 2. Be sure the bulb and junc­tion are submerged. Swirl the sensor.

j. The top line shows the actual buffer reading (S1 Live). Wait until the read-

ing is stable, then note the temperature. Change the pH in the second line
to the pH of the buffer at the measured temperature. Press ENTER.

k. If the calibration was successful, the analyzer will display the offset and

slope (at 25°C).

l. If the calibration was successful and if two sensors are wired to the ana-

lyzer, the Calibrate? screen appears. Choose the other sensor and
repeat steps c through j.

m. If the slope is out of range (less than 45 mV/pH or greater than 60 mV/pH),

an error screen appears. The display then returns to step g. Repeat the
calibration.

n. To return to the main display, press MENU followed by EXIT.

CCaalliibbrraattee

Hold

Program Display

Calibrate?

SSeennssoorr11

Sensor2

Calibrate?

Sensor1

SSeennssoorr22

CalSensor1?

MMeeaassuurreemmeenntt

Temp

S1BufferCal?

Auto

MMaannuuaall

S1ManualCal?

BBuuffffeerr11

Buffer2

S1 Standardize

Slope

BBuuffffeerrCCaall

S1Live 7.00pH

Buf1

00

7.00pH

S1Live 10.00pH

Buf2

11

0.00pH

S1Offset 6mV

Slope 59.16 25

°C

Calibration Error!

S1ManualCal?

Buffer1

BBuuffffeerr22

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

6.5 MAKING THE ANALYZER READING MATCH A SECOND INSTRUMENT

(STANDARDIZATION)

6.5.1 Purpose

1. The pH measured by the Solu Comp II analyzer can be changed to match the reading from a second or ref­eree instrument. The process of making the two readings agree is called standardization.

2. During standardization, the difference between the two pH values is converted to the equivalent voltage. The
voltage, called the reference offset, is added to all subsequent measured cell voltages before they are con­verted to pH. If a standardized sensor is placed in a buffer solution, the measured pH will differ from the buffer
pH by an amount equivalent to the standardization offset.

6.5.2 Procedure

1. Install the sensor in the process liquid.

2. Once readings are stable, measure the pH of the liquid using a referee instrument.

3. Because the pH of the process liquid may change if the temperature changes, measure the pH of the grab
sample immediately after taking it.

4. For poorly buffered samples, it is best to determine the pH of a continuously flowing sample from a point as
close as possible to the sensor.

5. Standardize the Solu Comp II analyzer by following the steps below.

CCaalliibbrraattee

Hold

Program Display

Calibrate?

SSeennssoorr11

Sensor2

CalSensor1?

MMeeaassuurreemmeenntt

Temp

Invalid Input!

Max: 14.00pH

S1

SSttaannddaarrddiizzee

Slope BufferCal

S1

SSttaannddaarrddiizzee

Slope BufferCal

Live 7.00pH

CalS1

00

7.00pH

a. Press MENU. The main menu screen appears. Choose Calibrate.

b. Choose Sensor1 or Sensor2. For a single input configuration, the

Sensor1 Sensor2 screen does not appear.

c. Choose Measurement.

d. Choose Standardize.

e. The top line shows the present pH reading. Change the pH reading in the

second line to match the referee instrument. Press ENTER.

f. The screen at left appears if the entered pH was greater than 14.00. The

display then returns to step e. Repeat the standardization.

g. If the entry was accepted, the screen at left appears. To verify that the

new pH was accepted, return to the main display by pressing MENU fol­lowed by EXIT.

h. To standardize the second sensor, repeat steps a through e.

i. To return to the main display, press MENU followed by EXIT.

41

42

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

6.6 ENTERING A KNOWN SLOPE VALUE

6.6.1 Purpose

If the electrode slope is known from other measurements, it can be entered directly in the Solu Comp II analyzer.
The slope must be entered as the slope at 25°C. To calculate the slope at 25°C from the slope at temperature t°C,
use the equation:

slope at 25°C = (slope at t°C)

Changing the slope overrides the slope determined from the previous buffer calibration.

6.6.2 Procedure

CCaalliibbrraattee

Hold

Program Display

Calibrate?

SSeennssoorr11

Sensor2

CalSensor1?

MMeeaassuurreemmeenntt

Temp

pH Slope 25°C?

S1: 59.16mV/pH

Changing slope

overrides bufcal.

Invalid Input!

S1 Standardize

SSllooppee

BufferCal

S1 Standardize

SSllooppee

BufferCal

1. Press MENU. The main menu screen appears. Choose Calibrate.

2. Choose Sensor1 or Sensor2. For a single input configuration, the
Sensor1 Sensor2 screen does not appear.

3. Choose Measurement.

4. Choose Slope.

5. The screen at left appears briefly.

6. Change the slope to the desired value. Press ENTER.

7. The slope must be between 45 and 60 mV/pH. If the value entered is out­side this range, the screen at left appears.

8. If the entry was accepted, the screen at left appears.

9. To enter the slope for the other sensor, press EXIT twice. Choose the
other sensor and repeat steps 3 through 6.

10. To return to the main display, press MENU followed by EXIT.

298

t°C + 273

MODEL SOLU COMP II SECTION 6.0

CALIBRATION

6.7 ORP CALIBRATION

6.7.1 Purpose

1. For process control, it is often important to make the measured ORP agree with the ORP of a standard solu­tion.

2. During calibration, the measured ORP is made equal to the ORP of a standard solution at a single point.

6.7.2 Preparation of ORP standard solutions

ASTM D1498-93 gives procedures for the preparation of iron (II) - iron (III) and quinhydrone ORP standards. The
iron (II) - iron (III) standard is recommended. It is fairly easy to make, is not particularly hazardous, and has a shelf
life of about one year. In contrast, quinhydrone standards contain toxic quinhydrone and have only an eight-hour
shelf life.

Iron (II) - iron (III) standard is available from Rosemount Analytical as PN R508-16OZ. The ORP of the standard
solution measured against a silver-silver chloride reference electrode is 476±20mA at 25°C. The redox potential is

-476±20mA at 25°C.

6.7.3 Procedure

CCaalliibbrraattee

Hold

Program Display

Calibrate?

SSeennssoorr11

Sensor2

CalSensorN?

MMeeaassuurreemmeenntt

Temp

Live 600mV

CalSN

++

0000mV

1. Press MENU. The main menu screen appears. Choose Calibrate.

2. Choose Sensor1 or Sensor2. For a single input configuration, the
Sensor1 Sensor2 screen does not appear.

3. Choose Measurement.

4. The top line shows the actual ORP or redox potential (S1Live). Once the
reading is stable, change the number in the second line to the desired
value. Press ENTER.

5. The display returns to the Cal Sensor screen. Press EXIT. Choose the
other sensor and repeat steps 2 through 4.

43

44

MODEL SOLU COMP II SECTION 7.0

MAINTENANCE

SECTION 7.0

MAINTENANCE

7.1 OVERVIEW

7.2 REPLACEMENT PARTS

7.1 OVERVIEW

The Solu Comp II analyzer needs little routine maintenance. The calibration of the analyzer and sensor should
be checked periodically. To recalibrate the analyzer and sensor, see Section 6.0.

Clean the analyzer case and front panel by wiping with a clean soft cloth dampened with water ONLY. Do not
use solvent, like alcohol, that might cause a buildup of static charge.

7.2 REPLACEMENT PARTS

Many components of the analyzer are replaceable. Refer to the table below to find the correct parts diagram.

Model Description See Figure

1055pH-10 Panel mounting enclosure 7-1

1055pH-11 Pipe/surface mounting enclosure 7-2

45

MODEL SOLU COMP II SECTION 7.0

MAINTENANCE

Location in Shipping

Figure 7-1 PN Description Weight

1 23823-00 Panel mounting kit, includes four brackets and 2 lb/1.0 kg

four set screws

2 note Enclosure, front, for panel mount version, includes keypad

3 33654-00 Gasket, front, for panel mount version 2 lb/1.0 kg

4 note Screw, 2-56 x 0.187 in., with integral washer

5 note Display board, LCD

6 note PCB, microprocessor

7 note Screw, self-tapping, #4 x 0.375 in.

8 note PCB, power supply, 115/230 Vac or 24 Vdc

9 note Screw, 4-40 x 0.31 in., with integral washer

10 33658-00 Gasket, rear cover, for panel mount version 2 lb/1.0 kg

11 note Enclosure cover, rear, for panel mount version, 115/230 Vac

11 note Enclosure cover, rear, for panel mount version, 24 Vdc

12 note Self-tapping screws, #6 x 1.25 in.

TABLE 7-1. Replacement Parts for Solu Comp II (Panel Mount Version)

FIGURE 7-1. Exploded View of Solu Comp II (Panel Mount Version)

Note: Information about circuit boards and size of screws and washers is for information only. Circuit boards, enclosure, display
board, and screws and washers cannot be purchased from Rosemount Analytical.
Shipping weights are rounded up to the nearest whole lb or 0.5 kg.

46

MODEL SOLU COMP II SECTION 7.0

MAINTENANCE

Location in Shipping

Figure 7-2 PN Description Weight

1 note Screw, 6-32 x 1.38 in.

2 note Washer

3 note Enclosure, front, for pipe/surface mount version,

includes keypad and hinge

4 33655-00 Gasket for pipe/surface mount version 2 lb/1.0 kg

5 note Screw, 2-56 x 0.187 in., with integral washer

6 note Display board, LCD

7 note PCB, microprocessor

8 note Self-tapping screw, #4 x 0.375 in.

9 note PCB, power supply, 115/230 Vac or 24 Vdc

10 note Screw, 4-40 x 0.31 in., with integral washer

11 note Enclosure, rear, for pipe/surface mount version,

includes standoffs and hinge brackets

not shown 23833-00 Surface mount kit; consists of four self-tapping 1 lb/0.5 kg

screws #6 x 1.75 in. and four O-rings

TABLE 7-2. Replacement Parts for Solu Comp II (Pipe/Surface Mount Version)

FIGURE 7-2. Exploded View of Solu Comp II (Pipe/Surface Mount Version)

Note: Information about circuit boards and size of screws and washers is for information only. Circuit boards, enclosure, display
board, and screws and washers cannot be purchased from Rosemount Analytical.
Shipping weights are rounded up to the nearest whole lb or 0.5 kg.

47

MODEL SOLU COMP II SECTION 8.0

TROUBLESHOOTING

SECTION 8.0

TROUBLESHOOTING

8.1 OVERVIEW

8.2 TROUBLESHOOTING USING FAULT CODES

8.3 TROUBLESHOOTING WHEN NO ERROR MESSAGE IS SHOWING

8.4 SIMULATING INPUTS

8.5 SIMULATING TEMPERATURE

8.6 MEASURING REFERENCE VOLTAGE

8.1 OVERVIEW

The Solu Comp II continuously monitors itself and the sensor for faults. When the analyzer detects a fault, the
word fault appears in the display alternately with the measurement. If alarm 3 was configured as a fault alarm,
the alarm relay will energize. The outputs do not change during a fault condition. They continue to reflect the
measured pH, ORP, or temperature. Press "to display the fault codes.

8.2 TROUBLESHOOTING USING FAULT CODES

8.2.1 Absolute Value of Measured Voltage Exceeds 2500 mV

The voltage of a pH cell is usually between 600 mV and -600 mV, and the voltage of an ORP cell is between 2000
and -2000 mV. Readings outside the range -2500 mV to 2500 mV usually indicate a problem with sensor wiring or
analyzer electronics.

A. If the sensor is being installed for the first time, check the wiring connections. See Section 3.3. If a junction

box is being used, be sure to check all connections at the junction box, too.

B. If the preamplifier is in a junction box, verify that the wires supplying the power (±5 Vdc) to the preamplifier are

connected at the analyzer and junction box.

C. Verify that the sensor is completely submerged in the process liquid.

8.2.2 pH Sensitive Glass Membrane is Broken

The Solu Comp II continuously measures the impedance between the sensor solution ground and the inside of the
pH-sensing electrode. If the glass membrane is intact, the impedance is normally between 10 MΩ and 1000 MΩ.
If the membrane is cracked or broken, the impedance drops below 10 MΩ. If the membrane is cracked or broken,
the sensor must be replaced.

8.2.3 RTD for Sensor 1 or Sensor 2 Open or Shorted.

There is an open or short in the sensor RTD or wiring.
A. If sensor is being installed for the first time, check the wiring connections. See Section 3.0.
B. Disconnect the sensor from the analyzer and measure the resistance between the RTD lead wires. See the

sensor manual to identify the RTD leads. If there is an open or short circuit, replace the sensor.

C. If there is no open or short, check the analyzer. See Section 8.4.

Fault Code Explanation See Section

S1 or S2 Out of Range Absolute value of measured voltage exceeds 2500 mV 8.2.1
S1 or S2 Broken Glass pH sensitive glass membrane is broken 8.2.2
TC1 Open or TC2 Open RTD for sensor 1 or sensor 2 is open 8.2.3
TC1 Shorted or TC2 Shorted RTD for sensor 1 or sensor 2 is shorted 8.2.3
S1 or S2 Sense Line Open RTD sense line for sensor 1 or sensor 2 is open 8.2.4
EEPROM Failure EEPROM failure 8.2.5

48

MODEL SOLU COMP II SECTION 8.0

TROUBLESHOOTING

8.2.4 RTD Sense Line for Sensor 1 or Sensor 2 is Open.

The Solu Comp II measures temperature using a three-wire RTD inside the sensor. See Figure 8-3. The in and
return leads connect the RTD to the measuring circuit in the analyzer. A third wire, called the sense line, is con­nected to the return line. The sense line allows the analyzer to correct for the resistance of the in and return leads
and to correct for changes in lead wire resistance with temperature.

A. Verify that all wiring connections are secure.

B. The analyzer can be operated with the sense line open. The measurement will be less accurate because the

analyzer can no longer correct for lead wire resistance and for changes in lead wire resistance with ambient
temperature. However, if the sensor is to be used at approximately constant temperature, the lead wire resist­ance error can be eliminated by calibrating the sensor at the measurement temperature. Errors caused by
changes in lead wire resistance with changes in ambient temperature cannot be eliminated.To make the error
message disappear, connect the RTD sense and return terminals with a jumper.

8.2.5 EEPROM Failure.

Call the factory at [phone].

8.3 TROUBLESHOOTING WHEN NO ERROR MESSAGE IS SHOWING.

Problem See Section

New temperature during calibration more than 2-3°C different from the live reading 8.3.1

Calibration Error warning during two-point calibration 8.3.2

Calibration Error warning during standardization 8.3.3

Invalid Input while manually entering slope 8.3.4

Sensor does not respond to known pH changes 8.3.5

Calibration was successful, but process pH is slightly different from expected value 8.3.6

Calibration was successful, but process pH is grossly wrong and/or noisy 8.3.7

Current output too low 8.3.8

Alarm relays do not operate when alarm setpoint is exceeded 8.3.9

Display is unreadable -- too faint or all pixels dark 8.3.10

8.3.1 Difference Between Solu Comp II and Standard Thermometer is Greater Than 3°C.

If an error message appears during a temperature calibration, check the following:

A. Is the standard thermometer, RTD, or thermistor accurate? General purpose liquid-in-glass thermometers, par-

ticularly ones that have been mistreated, can have surprisingly large errors.

B. Is the temperature element in the pH sensor completely submerged in the test liquid?

C. Is the standard temperature sensor submerged to the correct level?

D. Review Section 6.2.2.

MODEL SOLU COMP II SECTION 8.0

TROUBLESHOOTING

8.3.2 Calibration Error During Two-Point Calibration

Once the two-point (manual or automatic) calibration is complete, the Solu Comp II automatically calculates the
sensor slope (at 25°). If the slope is greater than 60 mV/pH or less than 45 mV/pH, the analyzer displays the
Calibration Error screen and does not update the calibration. Check the following:

A. Are the buffers accurate? Inspect the buffers for obvious signs of deterioration, such as turbidity or mold

growth. Neutral and slightly acidic buffers are highly susceptible to molds. Alkaline buffers (pH 9 and greater),
if they have been exposed to air for long periods, may also be inaccurate. Alkaline buffers absorb carbon diox­ide from the atmosphere, which lowers the pH. If a high pH buffer was used in the failed calibration, repeat the
calibration using a fresh buffer. If fresh buffer is not available, use a lower pH buffer. For example, use pH 4
and 7 buffer instead of pH 7 and 10 buffer.

B. Was adequate time allowed for temperature equilibration? If the sensor was in a process substantially hotter

or colder than the buffer, place it in a container of water at ambient temperature for at least 20 minutes before
starting the calibration. Using auto calibration avoids calibration errors caused by temperature drift. The ana­lyzer will not update readings until the drift is less than 0.02 pH over 10 seconds.

C. Were correct pH values entered during manual calibration? Using auto calibration eliminates errors caused by

improperly entering data.

D. Is the sensor properly wired to the analyzer? Check the sensor wiring including any connections in a junction

box. See Section 3.0.

E. Is the sensor dirty or coated? See the sensor instruction manual for cleaning instructions.

F. Is the sensor faulty? With the main display showing, use or to scroll through

the information screens until the electrode impedance screen (at left) is displayed.
Refer to the table for an interpretation of the impedance readings.

Another way of checking for a faulty sensor is to replace it with a new one. If the new sensor can be calibrat­ed, the old sensor has failed.

G. Is the analyzer faulty? The best way to check for a faulty analyzer is to simulate pH and temperature inputs.

See Section 8.4.

8.3.3 Calibration Error during Standardization.

During standardization, the millivolt signal from the pH cell is increased or decreased to force it to agree with the
pH reading from a referee instrument. A unit change in pH requires an offset of about 59 mV. The Solu Comp II
limits the offset to ±1400 mV. If the standardization causes an offset greater than ±1400 mV, the analyzer will dis­play the Calibration Error screen. The standardization will not be updated. Check the following:

A. Is the referee pH meter working and properly calibrated? Check the response of the referee sensor in buffers.

B. Is the process sensor working properly? Check the process sensor in buffers.

C. Is the sensor fully immersed in the process liquid? If the sensor is not completely submerged, it may be meas-

uring the pH of the liquid film covering the glass bulb and reference element. The pH of this film may be dif­ferent from the pH of the bulk liquid.

SRef Imp 123k^

Glass Imp 123M^

REFERENCE IMPEDANCE (Ref Imp)

less than 40 kΩ Normal reading, reference junction is clean.

between 40 and 140 kΩ Reference junction is fouled or dirty.

greater than 140 kΩ Reference junction is blocked or electrolyte is depleted. Sensor has failed.

GLASS IMPEDANCE (Glass Imp)

less than 10 MΩ Glass bulb is cracked or broken. Sensor has failed.

between 10 and 1000 MΩ Normal reading.

greater than 1000 MΩ pH sensor may be nearing the end of its service life.

49

50

MODEL SOLU COMP II SECTION 8.0

TROUBLESHOOTING

D. Is the sensor fouled? The sensor measures the pH of the liquid adjacent to the glass bulb. If the sensor is

heav-ily fouled, the pH of liquid trapped against the bulb may be different from the bulk liquid.

E. Has the sensor been exposed to poisoning agents (sulfides or cyanides) or has it been exposed to extreme

temperature? Poisoning agents and high temperature can shift the reference voltage many hundred millivolts.
To check the reference voltage, see Section 8.6.

8.3.4 Invalid Input While Manually Entering Slope.

If the sensor slope is known from other sources, it can be entered directly into the analyzer. The Solu Comp II will
not accept a slope (at 25°C) outside the range 45 to 60 mV/pH. See section 8.3.2 for troubleshooting sensor slope
problems.

8.3.5 Sensor Does Not Respond to Known pH Changes.

A. Did the expected pH change really occur? If the process pH reading was not what was expected, check the

performance of the sensor in buffers. Also, use a second pH meter to verify the change.

B. Is the sensor properly wired to the analyzer?

C. Is the glass bulb cracked or broken? Check the glass electrode impedance. See Section 8.3.2.

D. Is the analyzer working properly. Check the analyzer by simulating the pH input.

8.3.6 Buffer Calibration Is Acceptable, Process pH Is Slightly Different from Expected Value.

Differences between pH readings made with an on-line instrument and a laboratory or portable instrument are nor­mal. The on-line instrument is subject to process variables, for example ground potentials, stray voltages, and ori­entation effects that may not affect the laboratory or portable instrument. To make the process reading agree with
a referee instrument, see Section 6.5.

8.3.7 Calibration Was Successful, but Process pH Is Grossly Wrong and/or Noisy.

Grossly wrong or noisy readings suggest a ground loop (measurement system connected to earth ground at more
than one point), a floating system (no earth ground), or noise being brought into the analyzer by the sensor cable.
The problem arises from the process or installation. It is not a fault of the analyzer. The problem should disappear
once the sensor is taken out of the system. Check the following:

A. Is a ground loop present?

1. Verify that the system works properly in buffers. Be sure there is no direct electrical connection between
the buffer containers and the process liquid or piping.

2. Strip back the ends of a heavy gauge wire. Connect one end of the wire to the process piping or place it
in the process liquid. Place the other end of the wire in the container of buffer with the sensor. The wire
makes an electrical connection between the process and sensor.

3. If offsets and noise appear after making the connection, a ground loop exists.

B. Is the process grounded?

1. The measurement system needs one path to ground: through the process liquid and piping. Plastic pip­ing, fiberglass tanks, and ungrounded or poorly grounded vessels do not provide a path. A floating system
can pick up stray voltages from other electrical equipment.

2. Ground the piping or tank to a local earth ground.

3. If noise still persists, simple grounding is not the problem. Noise is probably being carried into the instru­ment through the sensor wiring.

C. Simplify the sensor wiring.

1. Disconnect all sensor wires at the analyzer except pH/mV IN, REFERENCE IN, RTD IN and RTD RE­TURN. See the wiring diagrams in Section xx.xx. If the sensor is wired to the analyzer through a remote
junction box containing a preamplifier, disconnect the wires at the sensor side of the junction box.

2. Tape back the ends of the disconnected wires to keep them from making accidental connections with other
wires or terminals.

MODEL SOLU COMP II SECTION 8.0

TROUBLESHOOTING

3. Connect a jumper wire between the RTD RETURN and RTD SENSE terminals (see wiring diagrams in
Section 3.2). Connect a second jumper wire between the REFERENCE IN and SOLUTION GROUND ter­minals.

4. If noise and/or offsets disappear, the interference was coming into the analyzer through one of the sensor
wires. The system can be operated permanently with the simplified wiring.

D. Check for extra ground connections or induced noise.

1. If the sensor cable is run inside conduit, there may be a short between the cable and the conduit. Re-run
the cable outside the conduit. If symptoms disappear, there is a short between the cable and the conduit.
Likely a shield is exposed and touching the conduit. Repair the cable and reinstall it in the conduit.

2. To avoid induced noise in the sensor cable, run it as far away as possible from power cables, relays, and
electric motors. Keep sensor wiring out of crowded panels and cable trays.

3. If ground loops persist, consult the factory. A visit from an experienced technician may be required to solve
the problem.

8.3.8 Current Output Too Low.

Load resistance is too high. Maximum load is 600 Ω.

8.3.9 Alarm Relays Do Not Work

A. Verify the relays are properly wired.
B. Replace power supply PCB (PN 23818-00)

8.3.10 Display is Unreadable.

While holding down the MENU key, press or until the display has the correct contrast.

8.4 SIMULATING INPUTS

8.4.1 General

This section describes how to simulate a pH input into the Solu Comp analyzer. To simulate a pH measurement,
connect a standard millivolt source to the transmitter. If the transmitter is working properly, it will accurately meas­ure the input voltage and convert it to pH. Although the general procedure is the same, the wiring details depend
on the location of the preamplifier.

8.4.2 Simulating pH input when the preamplifier is in the
analyzer.

1. Turn off automatic temperature correction and solution temper-

ature correction. From the Program menu, choose Temp. Then
choose Live/Manual and enter 25°C. See Section 5.6 for
details.

2. Disconnect the sensor and connect a jumper wire between the
pH IN and REFERENCE IN terminals.

3. From the display menu choose the pH/temperature/mV screen.
The measured voltage should be 0 mV and the pH should be

7.00. Because calibration data stored in the analyzer may be
offsetting the input voltage, the displayed pH may not be exact­ly 7.00.

4. If a standard millivolt source is available, disconnect the jumper
wire between pH IN and REFERENCE IN and connect the volt­age source as shown in Figure 8-1. Be sure to jumper the ref­erence and solution ground terminals.

FIGURE 8-1. Simulating Inputs When

the Preamplifier is in the Analyzer

51

52

MODEL SOLU COMP II SECTION 8.0

TROUBLESHOOTING

5. Calibrate the analyzer using the procedure in Section 6.3. Use 0.0 mV for Buffer 1 (pH 7.00) and -177.4 mV
for Buffer 2 (pH 10.00). If the analyzer is working properly it should accept the calibration. The slope should
be 59.16 mV/pH and the offset should be zero.

6. To check linearity, return to the main display and the pH/temperature/mV screen. Set the voltage source to the
values shown in the table and verify that the pH and millivolt readings match the values in the table.

8.4.3 Simulating pH input when the preamplifier is in a

junction box.

The procedure is the same as described in section 8.4.2.
Keep the connections between the analyzer and the junction
box in place. Disconnect the sensor at the sensor side of the
junction box and connect the voltage source as shown in
Figure 8-2.

8.4.4 Simulating pH input when the preamplifier is in

the sensor.

The preamplifier in the sensor simply converts the high
impedance signal into a low impedance signal without
amplifying it. To simulate pH values, follow the procedure in
Section 8.4.2.

8.5 SIMULATING TEMPERATURE

8.5.1 General.

The Solu Comp II accepts either a Pt100 or a Pt1000 RTD
in a three-wire configuration. See Figure 8-3.

Voltage (mV) pH (at 25°)

295.8 2.00

177.5 4.00

59.2 6.00

-59.2 8.00

-177.5 10.00

-295.8 12.00

FIGURE 8-2. Simulating pH Input When the

Preamplifier is in the Sensor.

FIGURE 8-3. Three-Wire RTD Configuration.

Although only two wires are required to connect
the RTD to the analyzer, using a third (and some­times fourth) wire allows the analyzer to correct
for the resistance of the lead wires and for
changes in the lead wire resistance with tempera­ture.

MODEL SOLU COMP II SECTION 8.0

TROUBLESHOOTING

8.5.2 Simulating temperature

To simulate the temperature input, wire a decade box
to the analyzer or junction box as shown in Figure 8-4.

To check the accuracy of the temperature measure­ment, set the resistor simulating the RTD to the values
indicated in the table and note the temperature read­ings. The measured temperature might not agree with
the value in the table. During sensor calibration an off­set might have been applied to make the measured
temperature agree with a standard thermometer. The
offset is also applied to the simulated resistance. The
Solu Comp II is measuring temperature correctly if the
difference between measured temperatures equals
the difference between the values in the table to with­in ±0.1°C.

For example, start with a simulated resistance of

103.9 Ω, which corresponds to 10.0°C. Assume the

offset from the sensor calibration was -0.3 Ω.
Because of the offset, the analyzer calculates tem­perature using 103.6 Ω. The result is 9.2°C. Now
change the resistance to 107.8 Ω, which corre­sponds to 20.0°C. The analyzer uses 107.5 Ω to cal­culate the temperature, so the display reads 19.2°C.
Because the difference between the displayed tem­peratures (10.0°C) is the same as the difference
between the simulated temperatures, the analyzer is
working correctly.

8.6 MEASURING REFERENCE VOLTAGE

Some processes contain substances that poison or
shift the potential of the reference electrode. Sulfide
is a good example. Prolonged exposure to sulfide
converts the reference electrode from a silver/silver
chloride electrode to a silver/silver sulfide electrode.
The change in reference voltage is several hundred
millivolts. A good way to check for poisoning is to
compare the voltage of the reference electrode with
a silver/silver chloride electrode known to be good.
The reference electrode from a new sensor is best.
See Figure 8-5. If the reference electrode is good,
the voltage difference should be no more than about
20 mV. A poisoned reference electrode usually
requires replacement.

Temp. (°C) Pt 100 (ΩΩ) Pt 1000 (ΩΩ)

0 100.0 1000
10 103.9 1039
20 107.8 1078
25 109.7 1097
30 111.7 1117
40 115.5 1155
50 119.4 1194
60 123.2 1232
70 127.1 1271
80 130.9 1309
85 132.8 1328
90 134.7 1347

100 138.5 1385

FIGURE 8-4. Simulating RTD Inputs.

FIGURE 8-5. Checking for a Poisoned

Reference Electrode.

Refer to the sensor wiring diagram to identify the
reference leads. A laboratory silver/silver chloride

electrode can be used in place of the second sensor.

53

54

MODEL SOLU COMP II SECTION 9.0

RETURN OF MATERIAL

SECTION 9.0

RETURN OF MATERIAL

9.1 GENERAL.

To expedite the repair and return of instruments, proper communication between the customer and the factory is
important. Before returning a product for repair, call 1-949-757-8500 for a Return Materials Authorization (RMA)
number.

9.2 WARRANTY REPAIR.

The following is the procedure for returning instruments still under warranty:

1. Call Rosemount Analytical for authorization.

2. To verify warranty, supply the factory sales order number or the original purchase order number. In the case
of individual parts or sub-assemblies, the serial number on the unit must be supplied.

3. Carefully package the materials and enclose your “Letter of Transmittal” (see Warranty). If possible, pack the
materials in the same manner as they were received.

4. Send the package prepaid to:

Emerson Process Management, Liquid Division
Liquid Division
2400 Barranca Parkway
Irvine, CA 92606

Attn: Factory Repair

RMA No. ____________

Mark the package: Returned for Repair

Model No. ____

9.3 NON-WARRANTY REPAIR.

The following is the procedure for returning for repair instruments that are no longer under warranty:

1. Call Rosemount Analytical for authorization.

2. Supply the purchase order number, and make sure to provide the name and telephone number of the individ­ual to be contacted should additional information be needed.

3. Do Steps 3 and 4 of Section 9.2.

NOTE

Consult the factory for additional information regarding service or repair.

9.1 GENERAL

9.2 WARRANTY REPAIR

9.3 NON-WARRANTY REPAIR

WARRANTY

Seller warrants that the firmware will execute the programming instructions provided by Seller, and that the Goods manufactured
or Services provided by Seller will be free from defects in materials or workmanship under normal use and care until the expira­tion of the applicable warranty period. Goods are warranted for twelve (12) months from the date of initial installation or eighteen
(18) months from the date of shipment by Seller, whichever period expires first. Consumables, such as glass electrodes,

membranes, liquid junctions, electrolyte, o-rings, catalytic beads, etc., and Services are warranted for a period of 90
days from the date of shipment or provision.

Products purchased by Seller from a third party for resale to Buyer ("Resale Products") shall carry only the warranty extended by
the original manufacturer. Buyer agrees that Seller has no liability for Resale Products beyond making a reasonable commercial
effort to arrange for procurement and shipping of the Resale Products.

If Buyer discovers any warranty defects and notifies Seller thereof in writing during the applicable warranty period, Seller shall, at
its option, promptly correct any errors that are found by Seller in the firmware or Services, or repair or replace F.O.B. point of man­ufacture that portion of the Goods or firmware found by Seller to be defective, or refund the purchase price of the defective por­tion of the Goods/Services.

All replacements or repairs necessitated by inadequate maintenance, normal wear and usage, unsuitable power sources, unsuit­able environmental conditions, accident, misuse, improper installation, modification, repair, storage or handling, or any other
cause not the fault of Seller are not covered by this limited warranty, and shall be at Buyer's expense. Seller shall not be obli­gated to pay any costs or charges incurred by Buyer or any other party except as may be agreed upon in writing in advance by
an authorized Seller representative. All costs of dismantling, reinstallation and freight and the time and expenses of Seller's per­sonnel for site travel and diagnosis under this warranty clause shall be borne by Buyer unless accepted in writing by Seller.

Goods repaired and parts replaced during the warranty period shall be in warranty for the remainder of the original warranty peri­od or ninety (90) days, whichever is longer. This limited warranty is the only warranty made by Seller and can be amended only
in a writing signed by an authorized representative of Seller. Except as otherwise expressly provided in the Agreement, THERE
ARE NO REPRESENTATIONS OR WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FIT­NESS FOR PARTICULAR PURPOSE, OR ANY OTHER MATTER WITH RESPECT TO ANY OF THE GOODS OR SERVICES.

RETURN OF MATERIAL

Material returned for repair, whether in or out of warranty, should be shipped prepaid to:

Emerson Process Management

Liquid Division

2400 Barranca Parkway

Irvine, CA 92606

The shipping container should be marked:

Return for Repair
Model

_______________________________

The returned material should be accompanied by a letter of transmittal which should include the following information (make a
copy of the "Return of Materials Request" found on the last page of the Manual and provide the following thereon):

1. Location type of service, and length of time of service of the device.

2. Description of the faulty operation of the device and the circumstances of the failure.

3. Name and telephone number of the person to contact if there are questions about the returned material.

4. Statement as to whether warranty or non-warranty service is requested.

5. Complete shipping instructions for return of the material.

Adherence to these procedures will expedite handling of the returned material and will prevent unnecessary additional charges
for inspection and testing to determine the problem with the device.

If the material is returned for out-of-warranty repairs, a purchase order for repairs should be enclosed.

Credit Cards for U.S. Purchases Only.

The right people,
the right answers,
right now.

ON-LINE ORDERING NOW AVAILABLE ON OUR WEB SITE

http://www.raihome.com

Specifications subject to change without notice.

Emerson Process Management

Liquid Division

2400 Barranca Parkway
Irvine, CA 92606 USA
Tel: [phone]
Fax: [phone]

http://www.raihome.com

© Rosemount Analytical Inc. 2005