Page 1
SuperSnap™ with Rod Connector
Instruction Sheet
Parts
Cable Clip
06-5050
SuperSnap
12S300
Instructions for assembly
Step 1
Insert single ball of ball chain into
inner channel of Cable Clip. The
cable should snap into place. Fig. 1
Align one round end of cable clip
with top channel of the rail and
insert. Once in place, insert end of
ball chain into channel. Then press
down on the other round end of the
cable clip and slide into rail by
pushing on the clip. Fig. 2
Note: Be sure to push on the cable
clip in order to slide the ball chain
into place. Do not pull on, or push
against, the ball chain as this will
cause it to bind in the channel.
Note: Position CableClip about
halfway down each SuperSnap. Fig. 3
End Caps
06-5475
Figure 1
6” Rod
97-0304-06
Ball Chains
96-0302P
Figure 2
Figure 3
Step 2
Push rod halfway into clip rail
of one SuperSnap. Fig. 4
Step 3
Insert rod into top clip rail of second
SuperSnap until both holders meet.
Fig. 5 & 6 Repeat steps 2-3 for
additional SuperSnaps.
Page 1 of 2
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
Incept-11.13.02
Figure 4
Figure 5
Figure 6
35 Congress Street, Salem, MA 01970
Tel# 1- 800 631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Page 2
SuperSnap™ with Rod Connector
Instruction Sheet
Parts
Cable Clip
06-5050
SuperSnap
12S300
Instructions for assembly
(continued)
Step 4
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 5
Insert poster (top and bottom) into
all sections of SuperSnap. Fig. 8
Step 6
To close, snap the SuperSnap shut.
Fig. 9
Step 7
Push end caps into place. Fig. 10
End Caps
06-5475
Open all
holders
6” Rod
97-0304-06
Ball Chains
Figure 7 Figure 8
96-0302P
Step 8
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Page 2 of 2
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
Incept-11.13.02
Figure 10Figure 9
Finished Look
35 Congress Street, Salem, MA 01970
Tel# 1- 800 631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Page 3
SuperSnap™ with Rod Connector
Instruction Sheet
Parts
Cable Clip
06-5050
SuperSnap
12S300
Instructions for assembly
Step 1
Insert single ball of ball chain into
inner channel of Cable Clip. The
cable should snap into place. Fig. 1
Align one round end of cable clip
with top channel of the rail and
insert. Once in place, insert end of
ball chain into channel. Then press
down on the other round end of the
cable clip and slide into rail by
pushing on the clip. Fig. 2
Note: Be sure to push on the cable
clip in order to slide the ball chain
into place. Do not pull on, or push
against, the ball chain as this will
cause it to bind in the channel.
Note: Position CableClip about
halfway down each SuperSnap. Fig. 3
End Caps
06-5475
Figure 1
6” Rod
97-0304-06
Ball Chains
96-0302P
Figure 2
Figure 3
Step 2
Push rod halfway into clip rail
of one SuperSnap. Fig. 4
Step 3
Insert rod into top clip rail of second
SuperSnap until both holders meet.
Fig. 5 & 6 Repeat steps 2-3 for
additional SuperSnaps.
Page 1 of 2
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
Incept-11.13.02
Figure 4
Figure 5
Figure 6
Page 4
SuperSnap™ with Rod Connector
Instruction Sheet
Parts
Cable Clip
06-5050
SuperSnap
12S300
Instructions for assembly
(continued)
Step 4
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 5
Insert poster (top and bottom) into
all sections of SuperSnap. Fig. 8
Step 6
To close, snap the SuperSnap shut.
Fig. 9
Step 7
Push end caps into place. Fig. 10
End Caps
06-5475
Open all
holders
6” Rod
97-0304-06
Ball Chains
Figure 7 Figure 8
96-0302P
Step 8
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Page 2 of 2
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
Incept-11.13.02
Figure 10Figure 9
Finished Look
Loading...