Rose displays ANOQUICK SQUARE WITH CABLE CLIP AND BALL CHAIN User Manual

AnoQuick™

Square Profile Instruction Sheet

Parts

Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.

Instructions For Hanging

Step 1

Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1

Step 2

Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2

Step 3

Insert single ball of ball chain into inner channel
of Cable Clip. The cable should snap into place.

Fig. 3

Step 4

Align one round end of cable clip with top chan­nel of the aluminum rail and insert. Once in
place, insert end of ball chain into channel. Then
press down on the other round end of the cable
clip and slide into rail by pushing on the clip.

Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or
push against, the ball chain as this will cause it to
bind in the channel.

Step 5

Push end caps into place. Fig. 5

Step 6

Suspend poster. Fig. 6

AnoQuick

12A300SQ

Cable Clips

06-5050

End Caps

06-5545

Figure 1

Ball Chains

96-0302P

Figure 2

Figure 3 Figure 4

Figure 5

Figure 6

The AnoQuick is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickSQCableClipBallChain

Incept-7.4.02

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]

AnoQuick™

Square Profile OneUp

Parts

Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.

Instructions For Hanging

Step 1

Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1

Step 2

Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2

Step 3

Insert single ball of ball chain into inner channel
of Cable Clip. The cable should snap into place.

Fig. 3

Step 4

Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4

Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or
push against, the ball chain as this will cause it to
bind in the channel.
Note: For OneUp applications, the AnoQuick

holder is conveniently marked in the center.
Slide the Cable Clip to the mark.

Step 5

Push end caps into place. Fig. 5

Step 6

Suspend poster. Fig. 6

AnoQuick

12A300SQ

Cable Clip

06-5050

®

Instruction Sheet

End Caps

06-5545

Figure 1

Ball Chain

96-0302P

Figure 2

Figure 3 Figure 4

Figure 5

Figure 6

The AnoQuick is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickSQCableClipBallChain

Incept-7.4.02

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]