Rose displays ANOQUICK ROUND WITH CABLE CLIP AND BALL CHAIN User Manual

AnoQuick™

Instruction Sheet

Parts

Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.

Instructions for Hanging

Step 1

Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1

Step 2

Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping it
down firmly to seat the graphic fully. Fig. 2

Step 3

Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3

Step 4

Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4

Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.

Step 5

Push end caps into place. Fig. 5

Step 6

Suspend poster. Fig. 6

AnoQuick

12A300

Cable Clips

06-5050

Figure 3

End Caps

Figure 1

06-5525

Ball Chains

96-0302P

Figure 2

Figure 4

The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipBallChain

Incept-7.4.02

Figure 5

Figure 6

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]

AnoQuick™

OneUp® Instruction Sheet

Parts

Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.

Instructions for Hanging

Step 1

Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1

Step 2

Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping it
down firmly to seat the graphic fully. Fig. 2

Step 3

Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3

Step 4

Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4

Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.
Note: For OneUp applications, the AnoQuick holder

is conveniently marked in the center.
Slide the Cable Clip to the mark.

Step 5

Push end caps into place. Fig. 5

Step 6

Suspend poster. Fig. 6

AnoQuick

12A300

Cable Clip

06-5050

Figure 3

End Caps

Figure 1

Figure 5

06-5525

Ball Chain

96-0302P

Figure 2

Figure 4

Figure 6

The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipBallChain

Incept-7.4.02

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]