Rose displays ANOGOTCHA STAND User Manual

AnoGotcha

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

Finished look.

Read this instruction sheet carefully
before assembly. Separate all parts and
check quantities. Make sure all parts
are accounted for before discarding
any packaging materials.

If you experience any problems with
the assembly, please call Rose Displays
at 1-800-631-9707.

™

Stand

Instruction Sheet

Parts

AnoGotcha

Shell

12AT300

Important terms:

top AnoGotcha holder

vertical post

ball knobs

These are all the parts required to assemble 1 AnoGotcha Stand.

T-Gotcha

12GT100

9” round base

97-0302

vertical poles

97-0301

ball knobs &

threaded rods

97-0303
97-0304

shaped

end caps

97-0305

bottom AnoGotcha holder

9” round base

AnoGotcha

™

Stand

assembly continued

Step 1

• Locate four ball knobs and
two threaded rods.

• Screw one ball knob
onto one end of each
threaded rod.

Note:

Do not screw a ball
knob onto both ends
of threaded rods.

Step 2

• Screw the end of one
vertical pole onto the
threaded stud of each
9” round base.

• Repeat for both poles.

Screw ball knobs onto threaded rods.

Screw vertical poles onto 9” round bases.

Screw one ball knob on one end of
threaded rod and tighten.

You should have one ball knob on one end of each threaded rod.

vertical

pole

9” round
base

Screw one vertical pole onto each
9” round base.

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStand

Tighten with hands.

You should have two matching vertical poles with bases.

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]

AnoGotcha

™

Stand

assembly continued

Step 3

• Slide one T-Gotcha holder
into each AnoGotcha shell.

• Attach one shaped end
cap onto each end of both
AnoGotcha shells.

Step 4

• Slide one threaded rod with
ball knob (created in step 1)
through top hole in one
vertical pole (created in
step 2).

Insert T-Gotcha holders into AnoGotcha shells.

Attach top AnoGotcha holder onto vertical poles.

Slide T-Gotcha holder into each
AnoGotcha shell as shown.

Attach one shaped end cap onto
each end of AnoGotcha holders,
as shown.

shaped
end cap

AnoGotcha
shell

T-Gotcha

You should have two AnoGotcha holders with one
shaped end cap on each end.

ball knobs

top
AnoGotcha
holder

• Slide threaded rod
completely through top
channel of one AnoGotcha
holder (created in step 3)
and through top hole of
second vertical pole.

• Screw second ball knob
onto other end of threaded
rod. Tighten securely.

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStand

Slide threaded rod through the
top hole of one vertical pole and
then through top channel of one
AnoGotcha holder.

Slide threaded rod through top hole
in second vertical pole. Screw ball
knob tightly onto threaded rod.

9” round
base

Your stand should now look like this.

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]

vertical
pole

AnoGotcha

™

Stand

assembly continued

Step 5

• Choose the height slot
that matches the length
of your graphic.

• Slide one threaded rod with
ball knob (created in step 1)
through appropriate hole in
one vertical pole (created in
step 2) and through bottom
channel of one AnoGotcha
holder (created in step 3).

• Slide threaded rod through
corresponding slot of second
vertical pole.

Note:

Make sure the hinge on the
bottom T-Gotcha faces up
and in the same direction as
the hinge on the T-Gotcha
at the top of the stand.

Attach bottom AnoGotcha holder to vertical poles.

28”

48”

28”

48”

60”

Bottom AnoGotcha must be
attached at slot that matches
the length of your graphic.

T-Gotcha hinge must face up and in the same direction as T-Gotcha on the top.

• Loosely screw second
ball knob onto end of
threaded rod.

Note:

Ball knob must be kept loose
until graphic is inserted.

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStand

60”

Slide threaded rod through height
slot that matches the length of your
graphic and through bottom channel
of remaining AnoGotcha holder.

Slide threaded rod through matching
hole on opposite vertical pole.

Attach ball knob, but do not
tighten. Leave loose until
graphic is inserted.

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]

AnoGotcha

™

Stand

assembly continued

Step 6

• Open top AnoGotcha
holder and insert top
edge of your graphic
until it reaches the
top of the holder.
Snap shut top holder.

• Open the bottom
AnoGotcha holder and
insert bottom edge of your
graphic until it reaches the
bottom of the holder. Snap
shut bottom holder.

Step 7

• Hold both ball knobs on
bottom AnoGotcha holder,
and pull down slightly,
to tighten and straighten
your graphic.

Insert your graphic into AnoGotcha Stand.

Tension poster and tighten bottom AnoGotcha holder.

Poster inserted into top AnoGotcha holder. Poster inserted into bottom AnoGotcha holder.

Insert graphic into top
AnoGotcha holder.

Snap the holder shut.

AnoGotcha holder.

Snap the holder shut.Insert graphic into bottom

• Turn ball knobs in opposite
directions to secure bottom
AnoGotcha holder.

Your AnoGotcha stand is now
complete and ready for display.

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStand

Hold both knobs and pull down
slightly to tension graphic.

If you have any questions about your AnoGotcha Stand assembly, please call

Rose Displays at 1-800-631-9707 and we will assist you.

To tighten, turn ball knob in
your left hand towards you.

Turn ball knob in your right
hand away from you.

Your completed AnoGotcha Stand
should look similar to this.

35 Congress Street, Salem, MA 01970

Tel# [phone] Fax# [phone]

e-mail:[e-mail]