Page 1
2
CONNECT LEAD WIRES
Make sure the device is completely
turned OFF. Take the pads out of the
sealed package; insert the lead wire
pin into the electrode pigtail. Make
sure no bare metal is exposed.
Insert the lead wires into the output
sockets located at the top of the device. Note: If only using one channel,
only plug in 1 lead wire.
3
TURNING THE DEVICE ON OR OFF
Press the [ ] button to turn the device “ON” or “OFF”.
If there is an immediate need to pause treatment,
press the [ II ] button to pause treatment.
Press it again to continue treatment or press [ ]
to stop treatment and go back to the home screen.
6
SET PULSE RATE
8
7
TENS — SET PRESET PROGRAMS — P1 & P2
Select Treatment Mode
Press [ M/II ] button to select the TENS treatment
mode. Select the body part which you want to
treat. Press the body part button until the LCD
displays program “P1” or “P2” like the screen
on the left.
To set your treatment time refer back to Step 5.
To start your treatment refer back to Step 7.
5
9
TENS — SETTING THE MANUAL PROGRAM — U1
NMES — SETTING THE MANUAL PROGRAM — U1
Never remove the self-adhesive electrodes from the
skin while the device is turned on!
WARNING: Device will not work while charging. Device is
partially charged upon receipt. If the electrodes are not placed
rmly on the skin or the device has not connected with the lead
wires securely, and the output intensity level is equal or greater
than 10mA, the intensity will stop automatically.
IMPORTANT!
Select Treatment Mode
Press [ M/II ] button to select the TENS treatment
mode. Select the body part which you want to
treat. Then press the body part button until the
LCD displays program “U1” like the rst screen
on the left.
Set Treatment Time
Press [ S ] button to enter treatment time, “Min”
will ash. Press [ + ] or [ − ] adjust time.
Select Treatment Mode & Body Part
Press [ M/II ] button to select the NMES treatment
mode. Select the body part which you want to
treat. Then press the body part button until the
LCD displays program “U1” like the rst screen
on the left.
Set Treatment Time
Press [ S ] button to enter treatment time and the
“min.” will ash. Press [ + ] or [ − ] button to adjust
the treatment time.
Set Pulse Rate
Press [ S ] button to enter the pulse rate and
the “Hz” will ash. Press [ + ] or [ − ] button to
adjust pulse rate.
1
INSERT BATTERY
Press down on the belt clip to
release it. Remove the battery cover
and insert the battery as shown in
the diagram. Replace the battery
cover and belt clip.
1
2
3
4
5
6
7
12
11
10
9
8
LCD DISPLAY
Waveform Mode
Home Screen
Set Mode
Output: Start, Pause or Lock
Channel 1 intensity level
Compliance Meter (hours)
Output Intensity of Channel 1
Body Part Selection
Treatment Time (minutes)
Low-Battery Indicator
Load Indicator
Compliance Meter Mode
1
2
3
4
6
10
5
9
7
11
8
12
QUICK REFERENCE GUIDE – TWIN STIM IV PAG E 2 QUICK REFERENCE GUIDE – TWIN STIM IV PAG E 3 QUICK REFERENCE GUIDE – TWIN STIM IV PAG E 4
S
M /
Twin Stim IV
4
SELECT THERAPEUTIC BODY PART
There are 6 therapeutic body part buttons available:
neck, shoulder, hand, low back, knee and foot. Each
therapeutic part has 3 programs – P1, P2 and U1.
Total of 36 programs.
PULSE WIDTH & START TIME
Pulse Width
Press [ S ] button to enter the pulse width and the
“µs” will ash. Press [ + ] or [ − ] button to adjust the
pulse width.
Start Treatment
Press [CH1+] or [CH2+] to increase the output
intensity of channel 1 and/or channel 2. Press
[CH1−] or [CH2−] to decrease the output
intensity of channel 1 and/or channel 2.
When done, press [ S ] or [ ] to conrm and return
to the home screen.
10
SET PULSE WIDTH & PULSE RATE
Set Pulse Rate
Press [ S ] button to enter the pulse rate and
the “Hz” will ash. Press [ + ] or [ − ] button to
adjust pulse rate.
Pulse Width
Press [ S ] button to enter the pulse width and the
“µs” will ash. Press [ + ] or [ − ] button to adjust the
pulse width.
Page 2
QUICK REFERENCE GUIDE PAG E 1
Twin Stim IV
Model: DI2717
1
2
Top
Side Front Back
3
4
5
6
7
8
9
10
11
LCD Display
Body Part Selection
Channel 1 Intensity Buttons
Set Button
Power Button
Channel 2 intensity buttons
Pause Button
LED Charging Indicator Light
Lead Wire Output Sockets
Battery compartment cover
Belt Clip
USB Charging Port
1
2
3
4
5
6
7
8
9
10
11
12
The purpose of this guide is to assist you in correctly operating your InTENSity™
Twin Stim IV TENS/NMES (DI2717) unit. This device should only be used under
the continued supervision of a licensed physician. This guide is not intended
to replace or substitute the InTENSity™ Twin Stim IV Instruction Manual.
PLEASE READ THE INSTRUCTION MANUAL COMPLETELY BEFORE USING
THIS DEVICE. Read, understand and practice the IMPORTANT SAFETY
PRECAUTIONS AND WARNINGS found on pages 6 – 12 of your user manual.
Always follow the operating instructions prescribed by your healthcare provider.
S
M /
CH1 CH2
1
2
3
4
6
5
7
8
9
11
10
12
Twin Stim IV
ELECTRODES
4 PADS
WALL CHARGER
& USB CABLE
LEAD WIRES
1 PAIR
Li RECHARGEABLE
BATTERY
S
M /
Twin Stim IV
QUICK REFERENCE GUIDE – TWIN STIM IV PAG E 5 QUICK REFERENCE GUIDE – TWIN STIM IV PAG E 6
14
NMES — SET PRESET PROGRAMS — P1 & P2
11
SET RAMP UP TIME
12
SET CONTRACTION TIME
Set Ramp Up/Down Time
Press [ S ] button to set the ramp up and down
time and the “sec.” will ash and you will see
the below image circled in red on the screen.
Press [ + ] or [ − ] adjust the treatment time.
Set Contraction Time
Press [ S ] button to set the contraction time
and the “sec.” will ash along with the symbol
circled in red to the left. Then press [ + ] or [ − ]
button to adjust the time.
Set Relaxation Time
Press [ S ] button again to set the relaxation time
and the “sec.” will ash along with the symbol
circled in red to the left. Then press [ + ] or [ − ]
button to adjust the time.
After you nished settings, press [ S ] or [ ]
button to conrm, the device will back to standby
status.
To set your treatment time refer back to Step 5.
To start your treatment refer back to Step 7.
13
SET RELAXATION TIME
Select Treatment Mode
Press [ M/II ] button to select the NMES treatment
mode. Select the body part which you want to
treat. Press the body part button until the LCD
displays program “P1” or “P2” like the screen
on the left.
To set your treatment time refer back to Step 5.
To start your treatment refer back to Step 7.
Manufactured for:
Roscoe Medical
21973 Commerce Parkway
Strongsville, Ohio 44149
Ph: (800) 3-ROSCOE (376-7263)
www.roscoemedical.com
TM
Loading...