Page 1
QUICK REFERENCE GUIDE PAGE 1
The purpose of this guide is to assist you in correctly operating your TENS 7000 To Go™ unit.
Do not use this device for undiagnosed pain symptoms until consulting a physician. This guide
is not intended to replace or substitute the TENS 7000 To Go™ Instruction Manual. PLEASE READ
THE INSTRUCTION MANUAL COMPLETELY BEFORE USING THIS DEVICE. Read, understand and
practice the contraindications, warnings, cautions and operating instructions found on pages 4 – 5 of your
instruction manual. Always follow the operating instructions prescribed by your healthcare provider.
Top
2
Side
9
TENS 7000 TO GO™
UNIT
Lead connector sockets - 2 channels
1
On / o / intensity dial - 2 channels
2
3
Panel cover with reference guide
1
4
Front
4
10
7
Liquid crystal display (LCD)
5
Mode selection button
6
Set selection button
7
Increment control / increase button
8
Increment control / decrease button
9
Protective cover
10
Belt clip
8
TENS 7000 to Go DT6070
replacement parts :
6
3
5
GB7000 – Conductive Back Belt
WS3147 – Snap Wires
WW3005 – Lead Wires
TA9050 – Battery
BELT
ELEC TRODES
SPRAY
LEAD WIRES
SNAP WIRES
For more information about your TENS 7000 To Go™ unit, visit us online at roscoemedical.com or call 1-800-871-7858.
SPECIAL FEATURES
The belt feature of the TENS 7000 To Go™ allows
patients to comfortably apply stimulation to the lower
back without having to contort or twist into positions
commonly associated with the placement of selfadhesive electrodes. The belt ts comfortably under
clothes and the belt clip ensures continued mobility.
The TENS 7000 To Go™ features two protective covers
that prevent unintentional changes to settings.
Turn on device by rotating the dial clockwise and
select the desired intensity level. Turn o
device by turning dial counterclockwise to O.
Low battery indicator signals when battery is
low. Replace battery when stimulation feels weaker.
INSERT BATTERY
Press arrow and slide
battery compartment
cover open. Insert 9V
battery, matching the
+ and – ends to
those in unit.
The battery should
be place on top of the
compartment ribbon
to allow easy battery
removal.
Page 2
QUICK REFERENCE GUIDE PAGE 2
Steps 1 – 4 should be performed with the device turned OFF.
IMPORTANT!
Once the unit has been turned ON, do not remove the belt
without rst turning OFF the device.
CONNECT LEAD WIRES
1
TO BELT WIRE SNAPS
Connect snap wires to metal snaps located on the back
of the belt. Securely connect the lead wires to the snap
wires. Make certain no bare metal of pins is exposed.
PLACE BELT
4
AROUND WAIST
With the electrode
pads facing toward
your body, position
the belt on your
lower back. After
a comfortable t
has been achieved,
fasten belt by
overlapping the
Velcro® closure
in front.
CONNECT LEAD WIRES
2 3
TO DEVICE
Select one of
the two available
channels and
insert the lead
wire rmly into
the socket.
Apply two pumps of conductive spray to interior side
of each electrode before placing belt around waist.
TURN DEVICE ON AND
5
SELECT INTENSITY
By turning the
controls clockwise,
the appropriate
channel is switched
on and the indicator
of power (CH1 and
CH2) is revealed in
the LCD.
The stimulation output will increase as the dial is
turned clockwise or to a higher number.
1 = Weaker 8 = Stronger
ON/
Increase
There are 5 modes available: Burst, Normal,
Modulation, SD1 and SD2. Press the MODE button
and continue to press until you have reached your
desired setting.
APPLY CONDUCTIVE
SPRAY TO ELECTRODES
SELECT
6
THERAPY MODE
SELECT PULSE WIDTH
7
The pulse width is adjusted from 50us to 300us. Press
the SET button to enter this menu, then press the s
and t buttons to adjust the setting. Unless otherwise instructed, a setting of 70-120us is suggested.
PROBLEMS WITH YOUR DEVICE?
SELECT PULSE RATE
8
The pulse rate is adjusted from 2Hz to 150Hz. Press the
SET button to enter this menu, then press the s and
t buttons to adjust the setting. Unless otherwise
instructed, a setting of 70-120Hz is suggested.
Please see page 26 of your TENS 7000 To Go™ Instruction Manual for troubleshooting tips.
SET THE TIMER
9
The treatment time is adjustable from 1 to 60 minutes,
or Continuous ( C ). Press the s and t buttons to adjust
the setting. Your settings will be stored permanently
unless they are adjusted again.
Continuous
Loading...