Rosco Smart-Vision STSK453X Series Installation & User Manual

90-21 144th Place

Jamaica, NY 11435

1.800.227.2095

www.roscovision.com

Smart-Vision

TM

4.3" Rearview

Mirror/Monitor Combo

Backup Camera System

INSTALLATION/USER'S MANUAL

STSK453X Series

STSK4530 Component List

Qty P/N Qty.

1

STSC130W (White)

STSC130R (Chrome)

STSC130B (Black)

*

system comes with 1 camera

with a choice of 3 colors:

BACK UP CAMERA, INCLUDES:

P/N STSC100X HIGH MOUNT, LOOK DOWN

CAMERA WITH HARDWARE

P/N STSH333 CAMERA POWER & SPLITTER

HARNESS

1 STSM230

BACK UP CAMERA MIRROR/MONITOR

INCLUDES:

P/N STSM1000 4.3" COLOR MIRROR MONITOR

P/N STSW1000 WINDSHIELD MOUNT #1 FOR

MIRROR MONITOR

P/N STSH4530 MONITOR POWER HARNESS

1 STSH330

BACK UP CAMERA EXTENSION HARNESS,

25FT, ROSCO, P/N STSH330

Notes:

• Please read this manual carefully before using the product.

• This system is intended as an aid to safe reverse operation. Drivers must always use extreme caution when operating a vehicle.

• Specications subject to change without prior notice.

Warning:

• To prevent electrical shock, DO NOT OPEN MONITOR CASE.

• Avoid exposing monitor to water, rain, moisture etc.

• Do not disassemble the camera. This voids the warranty. Disassembling the camera will compromise the waterproof seal.

1

www.roscovision.com

STSM230

STSW1000

STSM1000

STSH4530

STSH330

STSC1001 STSC1002 STSC1000

STSH333

STSC130W STSC130R STSC130B

STSK4531 Component List

Qty P/N Qty.

1

STSC130W (White)

STSC130R (Chrome)

STSC130B (Black)

*

system comes with 1 camera

with a choice of 3 colors:

BACK UP CAMERA, INCLUDES:

P/N STSC100X HIGH MOUNT, LOOK DOWN

CAMERA WITH HARDWARE

P/N STSH333 CAMERA POWER & SPLITTER

HARNESS

1 STSM231

BACK UP CAMERA MIRROR/MONITOR

INCLUDES:

P/N STSM1001 4.3" CLIP ON COLOR

MIRROR MONITOR

P/N STSH4530 MONITOR POWER HARNESS

1 STSH330

BACK UP CAMERA EXTENSION HARNESS,

25FT, ROSCO, P/N STSH330

Notes:

• Please read this manual carefully before using the product.

• This system is intended as an aid to safe reverse operation. Drivers must always use extreme caution when operating a vehicle.

• Specications subject to change without prior notice.

Warning:

• To prevent electrical shock, DO NOT OPEN MONITOR CASE.

• Avoid exposing monitor to water, rain, moisture etc.

• Do not disassemble the camera. This voids the warranty. Disassembling the camera will compromise the waterproof seal.

2

www.roscovision.com

STSH330

STSC1001 STSC1002 STSC1000

STSH333

STSM231

STSH4530

STSC130W STSC130R STSC130B

STSM1001

Smart-VisionTM 4.3" Rearview Mirror/Monitor Combo Backup Camera System

Rosco Vision Systems introduces a revolutionary new backup camera system for small to medium vehicles. Smart-Vision

TM

utilizes an interior rearview mirror to display a 4.3" LCD monitor when the vehicle shifts into reverse. This monitor allows the driver to see behind the vehicle for added convenience and safety.

The camera has an advanced CMOS lens sensor able to process excellent images under dark and light conditions. The camera has a 170° diagonal eld of vision giving superb coverage behind the vehicle and complies with the latest NHTSA 49 CFR Parts 571 and 585 (RIN 2127-AK43), when installed properly.

General Technical Specications:

Power Supply: 12VDC Power Consumption: ~3 Watt

Current Draw: ~250 mA Video Input: 1 Vp-p@75 impedance

Monitor Dimensions: 11"W x 3"H x 1.5"D

Installation Tools:

C O N T E N T S

How To Operate

Display .............. 4

Color Camera ... 7

Wiring

Diagram ......... 5-6

Rearview Mirror

Installation ....... 8

Camera

Installation ....... 9

Testing & Maintenance .. 10

3

A Century of Automotive Safety

1. Wire Tester 4. Wire Stripper 7. Drill

2. Phillips Screwdriver 5. Pencil 8. Tape

3. Tape Measure 6. Drill Bits 9. Wire Ties

(Not Shown)

1.

2.

3.

4.

5.

7.

8.

6.

4

www.roscovision.com

How To Operate Display:

1. V1/V2 - Not Applicable.

2. "Up" - Menu selection control.

3. Menu - Switches to setup menu.

4. "Down" - Menu selection control.

5. Power - Switches monitor off.

Typically not used

How To Set Your Monitor:

On-screen menu commands may be selected pressing the MENU button

while the mirror/monitor is on:

Brightness

Contrast

Saturation Hue Sharpness

4:3/16:9 Reset

How To Operate Display

Monitor Technical Specications:

Screen: 4.3" TFT Color LCD

Brightness: 350cd/m

2

Contrast ratio: 300:1

Resolution: 480 x 272 Current Draw: Max 120mA Video format: NTSC/PAL Display format: 4 : 3 or 16 : 9 Nomenclature: 12V Working Temp. °F(°C): -5° to 158° (-20° to 70°)

IMPORTANT: The Rearview Mirror/

Monitor is not intended to be used for prolonged periods of time. Therefore the monitor stays off until triggered by reverse circuit.

1.

2.

3.

4.

5.

Option #3: Power Provided From Front and Back of Vehicle (Least Common)

Option #2: Power Provided From Front of Vehicle

Option #1: Power Provided From Back of Vehicle (Most Common)

Option #3: Power Provided From Front and Back of Vehicle (Least Common)

AV1 (DO NOT USE)

PN: STSH4530

P/N: STSH330

P/N: STSH331

Note: Additional wire or adjustment to harness may be required.

P/N: STSH331

Note: Adjustment to harness may be required.

P/N: STSH331

P/N: STSH332

P/N: STSM100X

P/N: STSC100X

AV2

(Red)

DO NOT USE

7"

68"

7"

Trigger (Green)

(Red)

12V (Red)

Chassis Ground

Tie all 3 together

Tie both together

To Positive Reverse Light Wire At The Rear Of The Vehicle.

To reverse light circuit at front fuse box.

To Chassis Ground

5 6

Wiring DiagramWiring Diagram

Red Power Wire

12"

11"

3A 250V

11"

26'

2"

10"

2"

8"

3'

76"

To Positive Reverse Light Wire At The Rear Of The Vehicle.

3A 250V

(Red)

7

Color Camera

A Century of Automotive Safety

Camera Technical Specications:

Signal System: NTSC

Sync System: Internal

Horizontal Resolution: 420TVL Minimum Illumination: 0.2Lux Diagonal Angle: 170° Video Output: RCA, 1.0Vp-p,

75ohm

Waterproof Grade: IP67 Current Draw: Max. 90mA Nominal Voltage: DC12V Working Temp. °F(°C): -22° to 158° (-30° to 70°)

Features and Benets:

• Superb Night Vision

• 170° Diagonal eld of vision

• Easy installation

*STSC130 Color Camera is also available in chrome (Not Shown)

Rearview Mirror Installation

Figure. 2

Figure. 1

For standard mirror monitor

1. Attach windshield mounting bracket to the back of STSM230 mirror/

monitor. Be certain that the monitor

is in the upright position when attaching the mounting bracket. (Figure 1)

2. Remove old rearview mirror from factory mirror-mount tab.

3. Mount rearview mirror/monitor securely to mounting tab by tightening screw. (Figure 2)

4. Route the 8-pin connector end of the power harness to the location of mirror/monitor (preferably through the headliner and the vehicles A or B pillars).

5. Connect the power harness with the mating 8-pin receptacle end coming out of the mirror/monitor.

IMPORTANT: Please be certain to match both guiding lines on each connector for a proper connection.

For clip on mirror monitor

1. Expand STSM231 mirror monitor clamps and place over existing rear

view mirror

www.roscovision.com

Tightning Screw

8

9

Camera Installation

A Century of Automotive Safety

1. Select a high and centered location at the rear of the vehicle to mount

the STSC130 camera.

IMPORTANT: When selecting this

location it is highly recommended that the image transmitted by the camera show the rear bumper and area behind the vehicle.

2. We do not recommend mounting

the camera near the lower area of

the vehicle (ex. bumper). This reduces the view of the camera and increases the chance of physical damage to the camera.

3. Once the location for the camera

is chosen, drill the mounting hole to the inside of the vehicle using a 5/16 drill bit. Be sure to clear any obstacles before drilling hole.

4. Attach the provided 3M double sided tape to the back of the

camera.

5. Insert camera wire through newly drilled hole and mount securely in place.

6. To nalize the camera installation, hand tighten the provided 5/16 nut to the back of the camera on the inside of the vehicle.

Figure. 1

Figure. 2

Figure. 3

Camera mount in

suggested location

Mount camera assembly high. (Centered)

Typical monitor image of view from properly

installed camera

Obstructions behind truck

Diamond Plate

Position of camera

10

A Century of Automotive Safety

Testing

How to Test:

1. Apply the parking brakes.

2. Turn Ignition on. (DO NOT TURN ON VEHICLE)

3. Shift into reverse gear.

4. Image should appear on the monitor.

Trouble Shooting:

Problem Solution

No power to monitor while reversing.

Check power and reverse trigger

connections.

"No Signal" appears while reversing.

1. Press AV1/AV2 button to change video inputs.

2. Check video input connections.

3. Check camera power connections.

Video image is not sharp. Check camera lens for debris.

Maintenance:

Always keep camera clear from dirt, snow, and mud. Clean camera with a soft

moist cloth.

A Century of

Automotive Safety

90-21 144th Place

Jamaica, NY 11435

www.roscovision.com

Ph. 1.800.227.2095 Fx. 1.718.297.0323

Printed in China

Lit. P/N: 04242012