Page 1
SAFE -T-SCOPE®
BACKUP CAMERA SYSTEMS
INSTALLATION / USER'S MANUAL
STSK5465
5" MONITOR & CAMERA KIT
Page 2
Safe-T-Scope® Backup Camera System STSK5465
PART NO. DESCRIPTION
COMPONENT LIST AND DESCRIPTION
2 3
STSC141
STSH214
5" MONITOR KIT
REARVIEW
CAMERA
4-PIN 26FT.
EXTENSION CABLE
STSM208
PART NO. DESCRIPTION
STSA1004 MONITOR
SUN SHADE KIT
STSM214/PHAR
POWER HARNESS
STSU1004
U-BRACKET
(NOT INCLUDED)
INCLUDES:
5" COLOR BACKUP CAMERA SYSTEM
TABLE OF CONTENTS
5" Color Backup Camera System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Components List and description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Camera Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Monitor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7
Monitor Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
System Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Rosco Vision Systems introduces a revolutionary new backup camera system for
commercial vehicles. The
backup camera system utilizes a 5'' inch monitor to display a
16:9 LCD screen when the vehicle shifts into reverse. This monitor allows the driver to see
obstructions behind the vehicle for added convenience and safety.
The camera has an advanced CCD image sensor able to process excellent views under
dark and light conditions. A 120° diagonal field of vision yields superb coverage behind
the vehicle, and complies with the latest U.S. DOT guidelines when installed properly.
DISCLAIMER
Page 3
Safe-T-Scope® Backup Camera System STSK5465
4 5
Camera mounted in
suggested location
Mount camera assembly high and centered
Position of camera
Typical monitor image of view from
properly installed camera
Obstructions behind truck
Position of camera
CAMERA KIT INSTALLATION
g 1
g 2
g 3
Vehicle Rear Bumper
CAMERA LOCATION
• Select a high and centered location at the
rear of the vehicle to mount the STSC141
camera. See Figure 1 & 2.
• Mounting the camera near the lower area
of the vehicle (e.g. the bumper) is not
recommended. This reduces the view of the
camera and increases the chance of physical
damage to the camera.
INSTALL MOUNTING BRACKET
• Once the location for the camera is chosen,
use a 3/16” drill bit to drill four holes into
the vehicle using the mounting bracket as a
guide. Be sure to clear any obstacles before
drilling holes.
• Using a 3/4” drill bit, drill a cable hole into
the vehicle using the large center hole in
the mounting bracket as a guide, or choose
a hole location as close as possible to the
camera.
INSTALL CAMERA
• Install the camera mounting bracket. Mount
the camera and sunshade onto the bracket.
Insert the camera cable into the vehicle
through the ¾” hole and install the cable
grommet on the hole.
• Connect the camera cable to the male-
pinned connector of the camera extension
cable (STSH214). Hand-tighten the coupling
ring on the camera cable to ensure a secure
connection, and slide the environmental
boot over the connection.
ROUTE EXTENSION CABLE
• Route the extension cable to the vehicle
cabin at the front of the vehicle. Adhere to
a minimum bend radius of 2”, and keep the
cable away from hot, rotating, or electrically
noisy components.
• Tuck the cable out of sight and secure/clamp
the cable at as many spots as possible to
prevent accidental snagging or damage to
the cable.
MONITOR INSTALLATION
• Find a mounting location inside the vehicle cabin that is convenient to the driver (e.g. center of
the dashboard, above the windshield on the ceiling, near the rear view mirror etc).
• Install U-Bracket as desired
• Attach the sunshade
• Using the 4 supplied thumb screws, attach the monitor/sunshade assembly to the U-Bracket
FINALIZING THE INSTALLATION
• Connect the monitor 13-pin connector to the power harness 13-pin connector.
• Connect the camera extension cable from the rear-view camera to the 4-pin connector on the
power harness. Slide the environmental sleeve of the extension over the connection.
• Tuck and fasten/clamp the power harness and extension cable as much as possible into the
vehicle under the dashboard/pillar liners/etc to be out of sight from the driver and passengers.
This reduces the possibility of the cables being hooked or snagged. Keep cables away from HOT,
ROTATING and ELECTRICALLY NOISY components.
• Adhere to a 2-inch bend radius for all cables to prevent damage.
• Connect the 3- Pin connection to vehicle source
FUEL TANKERS & OTHER SPECIALTY VEHICLES:
• All electrical equipment fitted to petroleum vehicles must be connected via battery master switch
and must be isolated from the battery while the vehicles are loading and unloading. For other
specialty vehicles, please check applicable code and regulations prior to installation.
• Always consult your dealer when fitting any electrical or electronic equipment to a vehicle fitted
with a CAN-bus multiplex system.
CHECK THE REAR VIEW IMAGE
• Apply the parking brake and start the vehicle. Shift into reverse to ensure the monitor powers on
and displays a rear image. Shift back into park/neutral and power off the vehicle.
• Adjust the angle camera as needed to achieve the desired rear view image. It is highly recommended that the image transmitted by the camera shows the rear bumper and area behind the
vehicle. See Figure 3.
MONITOR KIT INSTALLATION
Page 4
Safe-T-Scope® Backup Camera System STSK5465
STSK5465
Wiring Diagram
4 Pin Connector
RED WIRE: Connect
to +12VDC ignition
switched accessory
power (eg. radio)
CAMERA 2
CONNECTION
GREEN WIRE: Reverse
trigger wire. Connect to
vehicle backup light circuit.
Monitor will turn on when
the vehicle shifts into
reverse
POWER 12 VDC
GROUND
C1
STSH341 (65FT)
Camera Extension Cable
C1 REVERSE
TRIGGER (GREEN)
C2
C2 TRIGGER (WHITE)
(optional second camera)
CAMERA 1
CONNECTION
CAMERA 2
(OPTIONAL)
STSU1004 U-BRACKET
(NOT INCLUDED)
13-PIN DIN FEMALE
13-PIN DIN MALE
14 IN
STSK5465/PHAR
MONITOR POWER HARNESS
4-PIN DIN MALE
4-PIN DIN FEMALE
STSC141MT
CAMERA MOUNTING KIT
”
STSM208
6
7
Page 5
Safe-T-Scope® Backup Camera System STSK5465
8 9
MONITOR BUTTONS
i
NOTE: The monitor buttons do not function while the vehicle is in reverse.
The vehicle must be running and in park/neutral/drive to use the buttons.
It is recommended that the buttons are ONLY used in park/neutral.
POWER ON/OFF
Powers on the monitor and displays the Camera 1 channel by default.
LIGHT SENSOR (LEFT) POWER LED (RIGHT)
Used to adjust screen brightness automatically. Green when ON, Red when OFF
+/- VOLUME/MENU SETTING ADJUST BUTTONS
Adjusts the monitor sound volume by default.
Adjusts menu settings (e.g. brightness, contrast) according the menu setting selected
MENU SETTING AND PAGE TOGGLE
Brings up the monitor settings menu. Press the button again to scroll through the various
settings and to access the camera settings menu page (see following page).
MENU SETTINGS PAGE 1:
"MONITOR DIM MODE SETTINGS / MONITOR BRIGHT MODE SETTINGS"
Press the menu button (see preceding page) to access this menu. Press the menu button again to
scroll through the settings:
• BRIGHTNESS Press +/- to adjust the brightness.
• CONTRAST Press +/- to adjust the contrast
• COLOR Press +/- to adjust the color saturation
• TINT Press +/- to adjust the color tint/hue.
• LANGUAGE Press +/- to select the menu language.
• RESET Press either + or - to reset all menu settings to factory default.
MENU SETTINGS PAGE 2:
"CAMERA SETTINGS"
Keep pressing the menu button to access page 2 of the settings:
• CAM - HORIZONTAL Press +/- to flip the Camera image horizontally.
• CAM - VERTICAL Press +/- to flip the Camera image vertically.
• DIMMING Press +/- to choose between "bright", "dim" and "auto". Choosing
auto will allow the monitor to brighten and dim according to the amount of ambient light in the
cabin.
• SCALE Press +/- to toggle the scale grid ON or OFF. If ON, the scale grid will appear when
the driver shifts the vehicle into reverse in order to assist with distance perception.
• ADJUST SCALE Press + or - to begin adjusting the dimensions of the scale grid. Press - to
switch between the vertical features of the scale and the horizontal "rungs". Press + to change
the width, height, etc of the various features. Press MENU to save the settings and exit. See
figure 4 for an example of the scale grid.
g 4
i
NOTE: The monitor buttons do not function while the vehicle is in reverse. The
settings can only be adjusted when the vehicle is running in park/neutral/drive.
It is recommended that the buttons are ONLY used in park/neutral.
Page 6
Safe-T-Scope® Backup Camera System STSK5465
10 11
Image device: Sony ¼" CCD
Pixels: 270,000
TV lines: 420
InfraRed LED's: 18 High-Output
Minimum illumination: 0 Lux (infrared LED's on)
Night vision range: 30 feet
Video Output: 1.0 Vp-p, 75 Ohm
Shock rating: 100G
Vibration rating: 15G
Field of view: 120°
Operating temperature °F (°C): -4°F to +140°F (-20°C to + 60°C)
Storage temperature °F (°C): -40°F to +176°F (-40°C to + 80°C)
Weight: 0.6 lbs.
Dimensions W x H x D: 3" x 2" x 2"
• Please read this manual carefully before using the product.
• This system is intended as an aid to safe reverse operation.
• Drivers must always use extreme caution when operating a vehicle.
• Specifications subject to change without prior notice.
• Keep all cables AWAY from rotating and electrically noisy components.
•
Make sure all cables are fastened properly so that you can prevent wire chafing, kinks,
cuts, etc...
• Always consult your dealer when fitting any electrical or electronic equipment to a vehicle
fitted with a CAN-bus or multiple system.
NOTES
STSM208 Monitor: (Includes STSK5465/PHAR, BAS4560, STSDF1000)
STSC141 Camera: ( Includes Sunshade and Mounting Hardware)
• To prevent electrical shock, DO NOT
OPEN MONITOR CASE.
• Avoid exposing monitor to water, rain,
moisture etc.
• Do not disassemble the camera.
This voids the warranty.
• Disassembling the camera will
compromise the waterproof seal.
WARNING
65’ Heavy Duty w/ Twist - Lock Connectors
STSH341 Extension Harness: (Included in Kit)
Screen size (diagonal): 5"
Maximum No. of cameras: 2 Inputs/Channels
Screen ratio: 16:9
Contrast ratio: 500:1
Video Input: Composite, 1 V p-p +/- 20% @75 Ohms
Video system: NTSC
Voltage input: 12 ~32 Vdc
Operating temperature °F (C°): 5°F to 149°F (-15°C to +65°C)
Storage temperature: -4°F to +158°F (-20°C to + 70°C)
Shock rating: 8g
Vibration Rating: 6.9G @ 3mm amplitude & 10-30 Hz
Speaker Impedance: 8 Ohms
Weight: 0.66 lbs
Dimensions W x H x D: 5.47" x 4.05" x 1.09"
NOTES
Page 7
M080816F
A CENTURY OF AUTOMOTIVE VISION SAFETY
90-21 144th Place, Jamaica, New York 11435
TEL (800) 227-2095 • FAX (718) 297-0323
techsupport@roscovision.com
www.roscomirrors.com www.roscovision.com
Loading...