Rosco Safe-T-Scope 7” Waterproof Monitor, Safe-T-Scope 7'', STSK7360 Installation & User Manual
Safe-T-Scope™ 7” Waterproof
Rearview Backup
Camera System
INSTALLATION/USER’S MANUAL
STSK7360
90-21 144th Place
Jamaica, NY 11435
1.800.227.2095
www.roscovision.com
Contents
Safeguard Instructions........................................................ 2
Features & Contents............................................................. 5
Installation Instructions....................................................... 6
Wiring Camera & Monitor...................................................... 7
Function & Operation............................................................ 8
Monitor.........................................................................................8
Split Screen & Camera Select.....................................................8
Normal/Mirror View....................................................................10
Distance Marker.........................................................................12
Trigger Input...............................................................................13
Setting................................................................................ 16
Video System..............................................................................16
Dimmer....................................................................................17
Picture........................................................................................17
Language...................................................................................17
Factory Settings.........................................................................18
Installation of U-Bracket...................................................18
Installation of Duckfoot Mount.........................................19
Connection...................................................................20
Figure Drawings...........................................................21-25
Specifications..........................................................26
- 1 -
WARNING
CAUTION
NOTICE
CAUTION
Safeguard Instructions
7”Waterproof Monitor
Please read the “Safety Rules“ carefully before using this product.
Following the safety rules prevents users from damages related with the
misuse of the product. It is very important to follow these safety rules.
We state “Caution“ and “Warning“ to clarify any potential risk for a
damage associated with the misuse of the product.
This information is for user’s reference for better usability.
This information is for preventing damage.
This information is for preventing bodily harm.
User should follow safety rules.
Install all components while power is off.
- It may cause electronic shock or malfunction.
Do not connect the product directly to the battery, use switched ignition.
- It may cause battery discharge.
Do not use this product with multi socket or extended adaptor.
- It may cause unexpected heating, re and malfunction.
When product is not in use for an extended period of time - unplug it.
- It may cause re by short circuit due to heating.
Do not place near magnetic devices.
- It may cause malfunction and trouble.
Please ensure that the monitor is installed with enough room
for heat emission.
- 2 -
- 3 -
Controls
1. Automatic brightness control sensor
2. Dimmer
3. Mode
4. Up
5. Down
6. Left
7. Right
8. Menu
9. Power
10. Stand by lamp
11. Speaker (Waterproof)
1
2
3
4
5
6
7
8
10
9
11
Do not install product in direct sunlight, high temperature, or extremely humid areas.
- It may cause electronic shock or malfunction.
Please use this product within the voltage range specied.
- It may cause electronic shock or malfunction.
Do not place this product where air bag operation may occur..
- It may cause malfunction of air bag or injury due from bag hitting monitor.
Do not clean the exterior of the monitor using harsh abrasives or solvents.
- It may cause change of surface or malfunction.
Do not place this product in high vibration areas without appropriate mounting.
- It may cause damage or malfunction.
Do not drill or screw directly into body.
- It may cause electronic shock, re and malfunction.
If the monitor is emitting smoke or a burning smell disconnect immediately.
- It may cause re.
Do not disassemble, repair or remodel.
- It may cause malfunction and injury, void warranty.
When the power cable cord touches a metal case, cover it with a friction tape.
- Short circuit or disconnection of wire may cause a re.
After nishing the installation, please check that the brake lamp, head lamp, and
wipers operate properly.
- 4 -
1
FEATURE
7”Waterproof Monitor
• Water Resistant (IP67), Aluminum housing
• 4 camera INPUT (NTSC/PAL)
• 2, 3, 4 Split Screen Function
• Dimmer sensor built in
• 7” WVGA (800 x 480) Wide LCD Panel
CONTENTS
7”Waterproof Monitor
• Before using this product, please check contents below. If there are
any missing parts please contact sales agent.
2
*Design & Specication are subject to change without notice.
Monitor
Monitor Cable
Power Adaptor
Cable
Trigger Extension
Cable (x4)
Instruction
Manual
U-Bracket
Sun Visor
(Optional)
Duckfoot Mount
- 5 -
INSTALLATION INSTRUCTIONS
IMPORTANT: For typical rear-view installation, the rear
camera MUST be connected to the distribution harness at
the connector marked “REVERSE”
Note: The following instructions are for typical rear-view
application.
STSC107 CAMERA
1. Attach camera bracket close to rear marker lights, centered on vehicle (see Fig. 1).
Attachment point must be sturdy enough to support camera and bracket.
2. We do not recommend mounting the camera near the lower area of the
vehicle (ex: bumper). This reduces the view of the camera and increases
the chance of physical damage to the camera.
3. Attach camera to bracket using screws provided. Adjust angle as indicated
in Fig. 2. (Use rear bumper and back of vehicle as a reference point.)
4. Wind deector may be installed. This deector is designed to reduce the
buildup of dust, dirt and moisture on the camera lens. (See Fig.3)
STSM207 MONITOR
1. Attach monitor inside vehicle in a location convenient to the driver
(ex: center of dash, overhead, or ush-mounted in dash).
2. Attach the “duckfoot“ bracket to the dashboard or to the headliner
using self-tapping screws and/or adhesive pad.
3. Fasten monitor to “duckfoot“ and adjust mounting angle to allow optimum driver
viewing comfort. (See Fig. 4.)
CABLE
1. The camera to cable connection is waterproof. Be sure to position the cable
properly. The male end attaches to the camera. The female end attaches to the
power/video/audio distribution harness, typically located under the dashboard.
(See Fig. 5.)
IMPORTANT: For typical rear-view installation, the rear
camera MUST be connected to the distribution harness at
the connector marked “REVERSE”
2. Do not run the cable over sharp edges or corners. Do not kink the cable.
Keep the cable away from hot and rotating parts.
3. Fasten all cable runs, and secure all excess cable.
- 6 -
WIRING CAMERA AND MONITOR
1. Connect the red wire to an ignition switched accessory (ex: radio) power source,
and connect the black wire to chassis ground. See wiring diagram for connections
(See Fig. 5.)
2. Before drilling, be sure no cable or wire is on the other side. Be sure to drill
a 20mm (0.8in) diameter hole only.
3. Feed as much cable as possible into vehicle and clamp securely. This
reduces the possibility of it being hooked or snagged.
4. Keep all cables away from HOT, ROTATING and ELECTRICALLY NOISY
components.
5. Camera: Drill a 20mm (0.8in) diameter hole into vehicle body near the camera and
bracket. Insert camera cable into vehicle (be careful not to kink cable) and t
grommet into hole. Apply sealant around grommet to increase resistance to water
penetration. Connect camera to the camera extension cable which runs inside
the vehicle.
6. Monitor: The monitor terminates in a 13-pin connector, which should be connected
to the mating 13-pin receptacle end of the power/video/audio distribution harness.
7. For typical rear-view installation, connect the camera extension cable
from the rear-view camera to the harness’s connector marked REVERSE.
8. For multi-camera installations, be sure to mark each extension cable properly and
connect to the appropriate harness connector marked CA1 or CA2. Bundle excess
cable together using a cable tie or electrical tape.
9. The green wire is the REVERSE trigger wire. In typical rear-view installations,
connecting this wire to the vehicle’s backup light circuit will activate the rear-view
image whenever the vehicle shifts into reverse.
10. FUEL TANKERS & OTHER SPECIALTY VEHICLES: All electrical equipment
tted to petroleum vehicles must be connected via battery master switch and must
be isolated from the battery while the vehicle are loading and unloading. For other
specialty vehicles, please check applicable code and regulations prior
to installation.
11. Always consult your dealer when tting any electrical or electronic equipment to a
vehicle tted with a CAN-bus or multiplex system.
IMPORTANT : For installations requiring multiple cameras,
or for installations not requiring typical rear-view images,
please refer to the wiring diagram (Fig.5) and the particular vehicle’s electrical schematic for selection of proper
power and trigger connection points.
- 7 -
FUNCTIONS AND OPERATION
MONITOR
1. POWER
When the ignition is switched on, the monitor will be in standby mode (no image
will be on the screen), waiting for trigger signal.
When a trigger wire is energized by 12v power (such as backup lights turning on),
the image captured by the selected camera will appear on the monitor.
2. Pressing the power switch will change the monitor status from standby to
steady-on. Steady-on mode status will show rear cameras view.
3. VOLUME +/-
Adjust Speaker Volume
These buttons are also used to adjust the values within selected setting
of menu option
4. MODE
Switching the screen mode.
Press MODE once
Full screen changes to 2 split screen.
Press Mode twice
2 slpit screen changes to 3 split screen.
Press Mode three times
3 split screen changes to 4 split screen.
Press Mode four times
4 split screen changes back to full screen.
SPLIT SCREEN & CAMERA FUNCTION
1. SPLIT SCREEN SWITCH
In the split screen, press button to view the alternate split screen views
half view
1
tri view
1
quad view
1
quad view
2
tri view
2
half view
2
- 8 -
Loading...