
USER MANUAL - UBB
WHAT IS THE UBB?
• DC DRIVER FOR SL1 SWITCH OR MINI SWITCH
• 12 TO 35VDC INPUT
• WIRED AND WIRELESS DMX (LUMEN RADIO)
• WI-FI (ARTNET) / ETHERNET
• UPGRADABLE FIRMWARE VIA USB
USER MANUAL - SL1 SWITCH
1

USER MANUAL - UBB
2
1
9
1. Menu
• Go to the general menu
2. Back
• Step back in menu
• Lock/unlock UBB when
pressed for 2secs.
4
3
5
7
6
10
5. Dimmer button
• Press to change intensity or CCT
• Select ne or coarse dimming
when pressed
• Navigate through the menu and
push to validate
11
8
12
13
18
17
14
16
10. Attachment for shoulder
strap
11. DMX IN
12. DMX OUT
15
17. 8 pins connector for SL1 SWITCH
18. 4 pins connector for Mini SWITCH
3. SWITCH
• Change between CCT and
intensity control
4. CCT
• Quickly change from 3200°k
to 5600°K
• Enter the preset menu to
store or recall values
6. USB plug
• Upgrade the UBB’s rmware
7. 12~30VDC input
8. Connector for Wi antenna
9. Mounting plate for EPS and
Battery mounts
13. LAN IN
14. ON/OFF
• Turns SL1 or MINI SWITCH ON
15. Door for antennas storage
16. Connector for Wireless DMX
antenna
USER MANUAL - SL1 SWITCH
2

USER MANUAL - UBB
WIRELESS DMX MODE:
1. Connect the UBB to a power source (DMG EPS, DMG Battery mount or any
12 to 30VDC power supply)
2. Connect the Mini SWITCH or SL1 SWITCH to the UBB
3. Turn on the UBB by selecting which light you are powering (SL1 or Mini)
Four modes are available :
• LOCAL MODE
• DMX MODE
• Wireless DMX MODE
• CUSTOM MODE
LOCAL MODE:
Control the UBB locally with the dimmer button.
• Press the SWITCH button to change between CCT and
intensity control
• Press CCT button for a quick change between 3200°K and
5600°K
• Press the dimmer button to select coarse or ne intensity
tuning
DMX MODE:
Control the UBB remotely by cable with the DMX
protocol.
Control the UBB remotely with the Wireless DMX
protocol.
• Make sure the Wireless DMX antenna should be intalled
• Press the dimmer button to enter the DMX start number of
the UBB
• Validate by pressing go
In Wireless DMX mode,when in receiver mode, the green
dot indicates your device is connected to a receiver, the red dot indicates you are not
connected to a receiver. To unlink a receiver, press the «SWITCH» button for 5 seconds
until the dot blinks in red.
CUSTOM MODE:
In custom mode the UBB acts as a translator between
different protocols. It still controls the SL1 SWITCH or
Mini SWITCH connected to it.
• Make sure the Wireless DMX antenna should be installed if
sing Wireless DMX.
• Make sure the Wi-Fi antenna should be installed if using Wi-Fi.
• Press the dimmer button to select data input, data output
and DMX address.
• Validate by selecting «Go».
If Wi-Fi input is selected, the UBB creates a Wi-Fi networks with the following
specications:
SSID: UBB serial number
Password: dmglumiere
These informations can be nd in the “info” section of the UBB menu.
Wireless DMX dot is red when no signal is received, green when the UBB is connected
to a Wireless DMX emitter.
• Press the dimmer button to enter the DMX start number of
the UBB
• To unlink all receivers, press the «SWITCH» button for 5 seconds until the dot blinks in red.
To link all receivers, do a short press on the «SWITCH» button.
USER MANUAL - SL1 SWITCH
3

USER MANUAL - UBB
CUSTOM MODE (FOLLOWING) :
(...)
Wi-Fi dot is red when no signal is received, green when the UBB is connected to a Wi-Fi
device with an Art-Net app enabled.
UPGRADING THE UBB :
• Copy the le to a USB stick
• Insert the USB key in the UBB.
If a correct le is found on the USB stick, the UBB will prompt an upgrade menu.
• Select YES to upgrade
• Wait for upgrade to nish. The UBB will turn off and on automatically to
activate the upgrade.
INFO
Displays the rmware version, the Network name and password for the Wi-Fi mode.
:
USER MANUAL - SL1 SWITCH
4

USER MANUAL - UBB USAGE EXAMPLE
Light console
LAN
DMX
WIFI
WDMX
DMX
WDMX
Light 1
DMG Lumière lights or any
DMX enabled light
Light 2
DMX
Light 1
Light 2
DMG Lumière lights or any
DMX enabled light
WIFI
WDMX
Our wireless DMX is compatible with any powered devices.
WDMX WDMX WDMX
DMG Lumière lights or any Wireless DMX enabled light
USER MANUAL - SL1 SWITCH
5