FlexiElectric 30-66XXX-3
User Manual
Mounting Instructions
Keep this folder with product at all times!
PDF 6087 / 03.04.2019
PA 2004 00634
QR code to
mounting
video
Page 2
Contents
1. INTRODUCTION ................................................................................................................................................. 3
2. COMPLIANCE WITH EU-DIRECTIVES ........................................................................................................ 3
3. APPLICATION ..................................................................................................................................................... 3
4. TECHNICAL DATA FLEXI ............................................................................................................................... 4
5. INSTALLATION INFORMATION .................................................................................................................... 5
6. FLEXI ELECTRIC QUICKSTART GUIDE ..................................................................................................... 7
7. MOUNTING INSTRUCTIONS ........................................................................................................................... 8
7.1 Assembly of frame ......................................................................................................................................... 8
7.2 Mounting the frame on the wall .................................................................................................................. 10
7.3 Mounting of fittings for front fascia ............................................................................................................ 11
7.4 Mounting the worktop ................................................................................................................................. 11
7.5 Adjusting the worktop/ support arms .......................................................................................................... 12
7.6 Mounting the wooden front fascia .............................................................................................................. 12
7.7 Mounting the side fascia ............................................................................................................................. 13
7.8 Mounting the control unit ........................................................................................................................... 13
7.9 Mounting the operating unit ....................................................................................................................... 14
7.10 Mounting of distance plates ......................................................................................................................... 15
7.11 Mounting of covers ................................................................................................................................ ...... 15
8. MOUNTING OF ACCESSORIES ..................................................................................................................... 15
8.1 Mounting the supporting feet ....................................................................................................................... 16
8.2 Mounting the covers for the legs ................................................................................................................. 16
8.3 Mounting the press pad for disabled persons .............................................................................................. 16
8.4 Mounting of distance plates for skirting board ........................................................................................... 17
8.5 Mounting the flexible water connections and waste hoses .......................................................................... 17
8.6 Montering af knægt 30-67642/30-67643 ...................................................................................................... 18
9. PERFORMANCE TEST .................................................................................................................................... 19
10. LIST OF COMPONENTS .................................................................................................................................. 20
11. OPTIONS FOR FLEXI ...................................................................................................................................... 22
12. SAFETY IN USE ................................................................................................................................................. 24
13. CLEANING AND MAINTENANCE ................................................................................................................ 25
13.1 Cleaning ...................................................................................................................................................... 25
13.2 Maintenance................................................................................................................................................ 25
13.3 Service schedule, operation and maintenance ............................................................................................ 26
14. TROUBLE SHOOTING ..................................................................................................................................... 26
15. CE-MARKING .................................................................................................................................................... 27
16. COMPLAINTS .................................................................................................................................................... 28
Page 3
1. Introduction
You have chosen Flexi, the multi-flexible, height-adjustable, easy-to-mount frame. The frame may
be used separately or in combination with Diagonal or Verti, the adjustable system for wall
cupboards.
The frame has no inconvenient fascia and, consequently, the adjustment of the working height
from 65 to 95 cm + worktop thickness may be fully utilised.
Under the worktop there is sufficient room for knees and legs for wheelchair users, who obtain
freedom of movement and a perfect working posture.
If you want the colour of the frame to match your kitchen, you may order suitable covers for the
vertical legs.
The Flexi frame is delivered with electrical function.
You have chosen the electrical version, and you will obtain a quick and easy adjustment of the
frame by activating the control buttons.
The correct use, operation and inspection are decisive factors for efficient and safe
performance.
2. Compliance with EU-Directives
This product has CE-marking according to the current Machinery, EMC and Low Voltage Directives
and thus complies with the basic safety requirements. See separate CE-declaration. See page
277.
If these table frames are assembled or otherwise connected with other electrical components, this
will be considered a new unit. Consequently, the assembled unit must be subjected to a risk
assessment, after which the CE mark may be awarded.
3. Application
The Flexi frame is adjustable in height in order to obtain optimum working height for user and
helper. Do NOT use Flexi as a lifting table or person lifter.
The product should be used indoor, at temperatures and humidity as described in section 4
The control unit complies with IP32/ll and must always be installed in accordance with the
national Heavy Current Regulations or corresponding national or international standards.
This document must ALWAYS be kept with the product and have been read and
understood by the user.
If this product is electrically adjustable in height there is a risk of squeezing. The
product must therefore always be operated by or under the guidance of an
experienced adult, who has read and understood the importance of section 11 ”Safety
in use”.
Page 4
4. Technical data Flexi
Product name: Ropox FlexiElectric
Length of worktop = 60-300 cm (205-300 cm supported by three
legs)
Item numbers: Electrical 30-66XXX: XXX = Length of worktop
The frame is always 5 cm shorter than the worktop
Height adjustment: 65–95 cm without worktop
Material: Welded steel tubes St. 37
Aluminium alloy 606045-T6
Stainless steel spindle and various plastic components
Surface treatment: Chromite, Powder coating, Standard RAL 9010, mat white
Max. load of frame: 150 kg evenly distributed over the entire worktop
Power supply: 230VAC / 2.5A / 50 Hz - Alternatively 100VAC / 50/60 Hz
Standby primary: ≤0,3W
Control voltage: 24VDC
Duty circle: Max. 10 % conform to 1 min. active / 9 min. pause
Speed: Approx. 32 mm/
sec
Lifting time stroke 30 cm: Approx. 10 sec.
Temperature: 5-45°C
Air humidity: 5-85% (non-condensing)
Complaints: See complaints, page 28.
Manufacturer: Ropox A/S, DK-4700 Naestved, Tel.: +45 55 75 05 00
Page 5
5. Installation information
Minimum area for reinforcement of wall. Wall material must be suitable for screw mounting.
Area for electric and plumbing installations.
Max. load 150kg evenly distributed over the worktop up to 300cm in width, according to DS/EN
12182.
Minimum load capacity per screw/bolt:
40 kg
The fitter should always consider the material, condition and strength of the wall and use screws
and rawlplugs suitable for the specific wall type.
Page 6
It is advisable to place water supply and waste within the hatched area. Also it is important to use
flexible hoses for water supply and waste to ensure that the Flexi will move freely without obstacles
within the height adjustment range 65-95 cm. excl. worktop.
It is advisable to place the water supply and waste close to the sink. The drain may also be
installed in the floor.
Arrange for the fixed feed pipes on the wall to be pointing down, at a height of max. 40 cm.
This will ensure that the flexible feed pipes will always flex in a neat curve close to the wall
without kinking. A 90 degree valve with a 1/2" exposed thread is recommended.
The control unit complies with IP32/ll and must always be installed in accordance with the
national Heavy Current Regulations or corresponding international or national standards.
The cables to the control unit must be able to move freely during height adjustment of the Flexi.
For worktops with cut-outs the distance from either side of the worktop should be considered as
shown on the illustration.
10 cm
10 cm
Always keep 0,5
cm space all away
around the
worktop
Min.
10cm
Min.
10cm
Page 7
6. Flexi electric Quickstart Guide
Checks:
•Bolts are firmly tightened on the frame and into the wall
•Stop rings and washers are in place on the spindle inside the legs
•The spindle runs fully through each leg
•There are no obstructions to full movement
Tips:
Upstand to worktop back to prevent items or
water flowing over
Space all around of 5mms
Control Box must be mounted
on
Underside of worktop
Check any potential gaps with
adjacent units or worktops
-either fill the gaps with fascia or
use
Ropox safety strips.
For adjacent adjustable frames a
Safety
Strip / Smartbox should be used
for each frame.
Press DOWN button first
Fascias on all
three sides
Recommendations:
•Ropox recommendation is to always make use of fascias on all 3 sides
Start-up:
•The frame must move freely and unimpeded throughout height adjustment. Check all connections of
flexible hoses, cables etc. to make sure none of these parts or other items are trapped when frame is
operated
Trouble shooting: - No movement – Check mains and power connection to control box
•Check adapter cable with end resistor is connected correctly to control box
•If frame is supplied with safety stop, remove/dismount connection to safety stop and replace yellow
end resistor. If frame moves downwards now, safety stop has to be examined to check if it is activated,
has been bend with a radius of less than 20mm or has been damaged
•Check if label on control box describes a Flexi control with either 1 or 2 motors, corresponding to
number of motors on the frame
•If you hear several “clicks” when connecting to main power it means plugs between control box,
motors and control switch are not connected correct or pushed/plugged right in (under normal
circumstances the control box would “click” twice)
•Before use:
•If these frames are mounted/installed or rebuild together with other electrical components, the whole
product will be looked at as a new unit and must therefore undergo risk assessment, by which it can
receive CE-marking
Page 8
7. Mounting instructions
Prior to assembly check that all parts have been provided. See list of components, from
page 20. If supporting feet have been ordered, follow assembly of these under paragraph
for mounting of accessories first.
7.1 Assembly of frame
The equipment should always be assembled by competent personnel.
7.1.1 Push the left leg into the groove of the
lower side of the aluminium profile.
7.1.4 Push the motor with fittings onto
the spindle. If the motor is not
parallel with the leg then turn the
motor to vertical position, see
7.1.7
7.1.3 Push the connecting spindle
through the leg on the left side.
Push the stop ring onto the
connecting spindle so it faces the
leg.
Stop ring
7.1.2 Position the adjustable legs on the
aluminium profile
For frames with two legs, place one
leg on either side. For frames with
three legs, place the third leg at the
middle of the aluminium profile.
Secure each leg to the aluminium
profile with two bolts.
2,5 cm
recommended
Leg can move to the side
Page 9
7.1.5 All support arms, but 2, may be
pushed into the aluminium profile from
the right hand side to the required
position and fastened with two screws
on each support.
We recommend a maximum distance
between the support arms of 60 cm in
order to obtain optimum stability.
7.1.6 The left hand side support arm may
be pushed into the profile, positioned
direct on top of the left leg and fasten
it.
7.1.8 Push the right-hand leg into the
groove of the bottom side of the
aluminium profile and fasten it in a
distance of 2,5 cm from the edge of
the aluminium.
7.1.7 For worktop length 105-300 cm an
additional motor must be mounted as
described.
Place the washer and stop ring between
the motor and the right-hand leg so that
the washer faces the leg.
Stop ring
7.1.9 Place the motors at the illustrated distance
from either end of the aluminium profile
and fasten them.
21,5 cm
18,5 cm
7.1.10 The right hand side support arm may
be pushed into the profile, positioned
direct on top of the left leg and fasten
it.
Page 10
Where you have an adjustable leg always position a support arm directly over it. Do not
adjust the tilting of the arm supports that are positioned on top of the legs (see 6.5).
If the sink or hotplate is placed at the middle of the worktop, move the third leg if any, to the
right or left to ensure that the leg and support arm are fitted in the immediate vicinity of the
sink, hotplate etc.
7.2.1 Place the frame against the wall and
align it. Adjust the two threaded bolts
under the legs to ensure that the frame
is horizontal.
To obtain the correct height (65-95 cm
without worktop) adjust the threaded
bolt to each leg.
After mounting, turn the threaded
bolts up so they are hidden by the
leg.
Mark and drill the holes for fastening.
Fasten the frame to the wall by means
of screws and raw plugs suiting the
material of the wall.
7.2 Mounting the frame on the wall
7.1.11 Move the stop rings on the spindle
to both sides, so that the stop ring
always faces the leg. Secure it by
fastening the screw in the stop rings.
7.2.2 Misalignments up to 0,45 cm on the
wall may be adjusted by fitting the
provided spacers (0,15 cm)
between the legs and the wall.
Loosen the legs a bit and slide the
spacers in between the wall and the
legs, as required, at the top or
bottom depending on whether the
wall is vertical.
Page 11
7.3.2 On the outermost support arms we
recommend pointing the front
fascia fittings towards the middle of
the frame to prevent them from
conflicting with the side fascia.
7.4.1 Place the tabletop on the frame. The
maximum permissible distance from
the back of the tabletop to the wall is
0.5 cm. (safety issue)
If the frame is moved away from the
wall, the distance from the back of
tabletop to the wall MUST still be
equal to or less than 0.5 cm.
7.4 Mounting the worktop
7.4.2 The standard aluminium profile
is 5 cm shorter than the worktop,
resulting in a 2.5 cm projection
on either side.
2,5cm
7.3 Mounting of fittings for front fascia
7.3.1 Fittings for mounting of the wooden
front fascia are provided,
corresponding to the number of
support arms. Place the front fascia
fittings on the side of the support arm
and fasten them loosely by means of
the screw provided.
Page 12
7.4.3 Fasten the worktop with
screws through the holes of
the support arms.
7.5.1 After placing the worktop on the
frame you may have to compensate
for the weight of the worktop if the
frame is no longer horizontal from
the wall to the front fascia.
7.6 Mounting the wooden front fascia
7.6.1 Fasten the wooden front fascia at
the required position under the
worktop by means of a clamp.
Press the front fascia fittings
forward against the wooden front
fascia and fasten with screws
from the inside.
7.5 Adjusting the worktop/ support arms
7.5.2 By means of the two lower screws of
each support arm the ”tilting” may
be adjusted.
Start by loosening the two screws
fastening the support arm to the
aluminium profile and adjust the two
lower screws to make the worktop
horizontal.
Finally retighten the two upper
screws.
Repeat this procedure for the
support arms in the middle.
Do not adjust the support arms
placed directly above the legs.
Page 13
7.7 Mounting the side fascia
Warning
ALWAYS switch off mains voltage during assembly
Check national regulations to determine the correct location of the control unit.
7.6.2 By screwing the front fascia
fittings into the worktop you
pull the front fascia upward.
Finally tighten the screws on
the side of the support arm.
7.7.1 Furniture fittings are provided
with the frame to keep the
wooden side fascia up against
the worktop.
7.8 Mounting the control unit
7.8.1 The 2 special nuts on the control box plate are turned vertically,
making them fit into the long track in the alu profile. The plate is
positioned on the front of the alu profile and the 2 M6 screws are
tightened. (The special nuts are automatically turned in place,
when the screws are tightened)
Page 14
Connections to Control box
Motor Cable M1
Motor Cable M2
Power Cable
Safety strip (option)
Cable for Control switch
Split Cable
for
safety stop
S2
7.8.2 Mount all cable connections as illustrated. Note that the safty strip sit in S2.
For connection sequence see section 8 (start-up procedure) on page 18
7.8.3 Place the loose cables in the
cable bearers and fit the
bearers in the grooves of the
aluminium profile.
7.9 Mounting the operating unit
7.9.1 The control switch for the height adjustment must
be fitted in the wooden front fascia. It consists of
a control switch with a 1,5 m long cable
provided with a DIN plug for the control switch.
Choose the required position in the front fascia
and drill an 18 mm dia. hole in the fascia.
Push the cable through the hole in the front
fascia from the front.
The control switch has double-adhesive tape on
the back. Remove the protective paper and fit
the control switch on the wooden front fascia.
Fit the DIN plug of the cable on the control
switch.
After fitting the socket, fasten the cable under
the worktop with the cable bearer so that it does
not sag.
Relieve the cable on the inside of the wooden
front fascia in the immediate vicinity of the control
switch.
Page 15
7.10 Mounting of distance plates
7.11.1 Place the 2 endcaps on
standard cover and push
over outer leg.
7.11 Mounting of covers
7.10.1 In case of skirting boards, you can
use the 1 cm deep distance plate to
pack the frame out from the wall.
Distance between backside of
worktop and wall has to be 0,5 cm
Page 16
8. Mounting of accessories
8.1 Mounting the supporting feet
8.2 Mounting the covers for the legs
8.3 Mounting the press pad for disabled persons
8.1.1 Remove the adjusting screw of
the leg.
8.1.2 Fit the foot and the extension to the
leg with the screws provided and
tighten the screws.
8.2.1 Press the covers, consisting
of an inside and an outside
cover, carefully over the leg.
8.2.2 Lift up the upper/outside cover and
press the snap lock into the hole of
the leg. It is important to pull the
snap lock completely out prior to
mounting. Now press in the snap
lock to lock it.
8.3.1 The press pad for height
adjustment must be placed in the
wooden front fascia. It consists
of a press pad contact and a 150
cm long cable provided with a
DIN-plug.
The press pad and the cable are
delivered as one unit ready for
mounting.
Drill holes as illustrated to suit the
required position.
8.3.2 Fit the press pad by pulling the
cable through the large hole and
fasten it in the small holes by
means of the M6 nuts provided.
Page 17
8.3.3 After fitting the press pad, fasten
the cable under the worktop with
cable bearers so that it does not
sag. Finally fit the DIN-plug in the
control unit.
8.4.1 In case of skirting boards, you
can use the 1 cm deep
distance plate to pack the
frame out from the wall.
8.4 Mounting of distance plates for skirting board
Location of drain
8.5.1 When connecting hot and cold water as
well as waste hoses ALWAYS use
flexible hoses to enable the frame to
move freely within the height
adjustment range (65-95 cm).
The flexible hoses should be fitted so
that they may move in an arch
parallel with the wall, but without
getting squeezed.
The length of the hoses must suit the
fastening and the travel of the frame.
We recommend that water seal and
waste pipe be directed backwards
towards the wall in order to obtain
optimum space under the table and
the sink.
8.5 Mounting the flexible water connections and waste hoses
Page 18
8.6 Montering af knægt 30-67642/30-67643
8.6.1 Push support arm into
aluminium profile and
make sure support arm is
level with profile.
Afterwards tighten screws.
By using this support arm it
is possible to mount
hotplate or sink closer to
edge of tabletop.
4,5 m
4,5 cm
Page 19
9. Performance test
After installation and prior to use all functions of Flexi must be tested. The test must be carried out
by competent personnel. Subsequently the test shall be carried out at least once a year:
Testing prior to connection of mains voltage:
1. Check that the mounting instructions have been observed.
2. Check that all bolts have been tightened.
3. Check that all cables have been connected correctly and that the plugs have been pressed
home.
4. Check that there is no load on the Flexi frame.
5. Check that there is nothing preventing the Flexi from moving freely within the height
adjustment range.
Start-up Procedure
1. Connect the net cable and turn on the power
2. Connect the motor cables to M1 and M2
3. Connect the control switch to HS
4. Press DOWN on the control switch, move the frame to bottom position, check that the
movement is even and smooth. Make sure that the hose connections follow the movement
of the frame and that they do not get squeezed. The frame is now reset.
5. Press UP on the control switch, move the frame to top position and check that the
movement is even and smooth. Make sure that the hose connections follow the movement
of the frame and that they do not get squeezed.
If a safety strip has been mounted under the Flexi frame it must be tested as follows:
Press DOWN on the control switch and let the Flexi frame move 2-5 cm downward. Now
activate the safety strip by pressing it lightly. The frame must stop the downward movement,
move 1-2 cm upward and stop.
If a safety strip and smartbox2 has been fitted above the frame, e.g. on a wall cupboard ”Diagonal”,
this must also be tested as follows:
Make sure that the Flexi frame is in the bottom position. Press UP on the button and let the
frame move 2-5 cm upward. Now the safety strip above the Flexi frame will be activated. The
Flexi frame must now stop its UPWARD movement and move 1-2 cm downward and stop.
If all these tests are ok, the Flexi frame is ready for use. Se section 12 “Safety in use”.
Page 20
10. List of components
Legs, Electric standard height 65-95 cm. 30-67607:
Length of worktop = 60-204 cm 2 legs
Length of worktop = 205-300 cm 3 legs
The legs comprise:
30-67681 Spacers (0.15 cm) 3 pcs./leg
For misalignment
30-67680 Distance plates (1 cm) 2 pcs/leg
For skirting board
30-67685 Cable bearer 1 pc/leg
30*65591-008 Basic cover 1 pc/leg
30*65591-009 End cover for basic cover 2 pcs/leg
Support arm for worktop 60-62 cm 30-67620:
Length of worktop = 60-104 cm 2 pcs.
Length of worktop = 105-204 cm 4 pcs.
Length of worktop = 205-249 cm 5 pcs.
Length of worktop = 250-300 cm 7 pcs.
Aluminium profile 30-68xxx:
Length (XXX) = Worktop length 5cm 1 pc.
At increments of 5 cm
The profile comprises:
30-69xxx Spindle 1 pc.
Length (xxx) = Worktop length -15cm
At increments of 5 cm
Motor (16x8x8 cm) 30-67800:
Length of worktop = 60-104 cm 1 motor
Length of worktop = 105-300 cm 2 motors
Incl. motor cable (200 cm) and fittings
Page 21
Control box, fast (26,5x10,5x3,7 cm):
Control box for 1 motor : 30-67859 1 pc
Worktop length = 60-104 cm
Control box for 2 motors: 30-67877
Worktop length = 105-300cm
240VAC, incl. netcable (250 cm)
Enclosed with control box:
96000598 Adapter cable
98002082 Adapter plug
98002035 End resistor 2,2 KΩ, yellow
97702-433 Plate for fitting of Contol box
30-67870 Extension cable 250 cm 1 pc
for safety stop (black)
30-67840 Control switch, (3x6 cm) 1 pc
incl. 150 cm cable
Mounting parts 30-67670:
30*65500-084 Stopring 2 pc
97002730 Angle fitting 4 pc
Page 22
11. Options for Flexi
Support arm for worktop depth 70-72 cm 30-67621:
Length of worktop = 60-104 cm 2 pcs.
Length of worktop = 105-204 cm 4 pcs.
Length of worktop = 205-254 cm 5 pcs.
Length of worktop = 255-300 cm 7 pcs.
Support arm for worktop depth 58-60 cm 30-67624:
Length of worktop = 60-104 cm 2 pcs.
Length of worktop = 105-204 cm 4 pcs.
Length of worktop = 205-254 cm 5 pcs.
Length of worktop = 255-300 cm 7 pcs.
Support arm for worktop depth 50-52 cm 30-67622:
Length of worktop = 60-104 cm 2 pcs.
Length of worktop = 105-204 cm 4 pcs.
Length of worktop = 205-254 cm 5 pcs.
Length of worktop = 255-300 cm 7 pcs.
Support arm for worktop depth 58-62 cm 30-67642:
Right side. Support arm is placed further out against the end of worktop.
1pcs.
Support arm for worktop depth 58-62 cm 30-67643:
Left side. Support arm is placed further out against the end of worktop 1 pcs
Distance plate (1 cm) 30-67680:
For skirting board 1 pc.
Distance bracket (7 cm) 30-67672:
For void behind the frame 1 pc.
Cover 30-67735:
Length of worktop = 60-204 cm 2 pcs.
Length of worktop = 205-300 cm 3 pcs.
Cover for supporting foot 30-67737:
Length of worktop = 60-204 cm 2 pcs.
Length of worktop = 205-300 cm 3 pcs.
Fittings for concealment panels 30-67760: 1 set
Page 23
Supporting foot, L = 30 cm 30-67702:
Length of worktop = 60-204 cm 2 pcs.
Length of worktop = 205-300 cm 3 pcs.
Supporting foot L = 49 cm 30-67703:
Length of worktop = 60-204 cm 2 pcs.
Length of worktop = 205-300 cm 3 pcs.
Each foot comprises:
30*65561-004 Leg extension for foot 1 pc.
Press pad (14x7 cm) 30-67841:
For disabled people, incl. 150 cm cable 1 pc.
Infrared control, 30-67849: 1 pc.
Range 150-200 cm
The infrared control is supplied with:
96000629: Split cable 1 pc.
Safety strip 30-69XXX:
Length ”X” in whole cm 1 pc.
Smartbox 30-69002:
Option for safety stop Flexi, 1 pc.
(when two Flexi frames are situated side by side).
Coupling Diagonal and Flexi 30-67002:
Option for safety stop plate Diagonal (40900) 1 pc.
To be ordered together with safety stop
The coupling comprises:
30-67870 Extension cord (250 cm) 1 pc.
Extension cord 30-67870:
For safety stop, 250 cm (black) 1 pc.
Spiral extension 30-67871:
For safety stop, 25-100 cm (black) 1 pc.
British standard 3-pin plug 30-67879:
with 200 cm cable 1 pc.
Page 24
12. Safety in use
➢ The Flexi frame should only be used by people, who have read and understood these
instructions.
➢ Flexi is a height-adjustable frame and should not be used as a lifting table or person lifter.
➢ On electrically height-adjustable Flexi frames we recommend the fitting of safety stop rails
in order to guard against and avoid injury and accidents. Nevertheless, always make sure
that there are no people, animals or objects under the Flexi frame during height adjustment.
➢ Always use the Flexi frame so there is no risk of damage to people or property. The person,
who operates the Flexi frame, is responsible for avoiding damage or injury.
➢ If the Flexi frame is used in publicly accessible locations where children or people with
reduced observation ability may get close to the Flexi frame, the person operating the Flexi
frame must pay sufficient attention in order to prevent dangerous situations.
➢ Make sure that there is free space above and below the Flexi frame to allow height
adjustment.
➢ Do not overload the Flexi frame and make sure that the load distribution is correct.
➢ Do not operate the Flexi frame in case of errors or damage.
➢ Do not use the Flexi frame in an explosive environment.
➢ Any modification of the Flexi frame, which may influence its operation or construction, is
forbidden.
➢ Installation, service and repairs must be carried out by competent personnel.
➢ In case of inspections, service or repairs make sure that the Flexi frame is not loaded.
➢ If the Flexi frame has not been installed in accordance with these mounting instructions, the
guarantee may become void.
➢ Only use Ropox original spare parts as replacement parts. If other spare parts are used, the
guarantee may become void.
Page 25
13. Cleaning and maintenance
13.1 Cleaning
The frame may get dirty during use. It is very important to clean the frame as described in these
instructions.
Clean the frame with a damp cloth using lukewarm water and ordinary cleaning agents. Do not use
Corrosive/ abrasive liquids or abrasive cloths, brushes or sponges. After cleaning dry the frame.
13.2 Maintenance
The frame is maintenance-free and the moving parts have been lubricated for life. For reasons of
safety and reliability we recommend inspection of the frame once a year.
During inspections:
➢ Check that all bolts have been tightened.
➢ Check that the frame moves freely from bottom to top position without problems.
➢ Resetting the frame: Press DOWN on the control switch and move the frame to bottom
position. Press DOWN once more and keep the switch depressed for 5 sec. to reset the
control unit. Check that the movement is even and smooth. Make sure that the mains cable
moves freely.
➢ Check that water and waste pipes are tight and undamaged.
➢ Check that all cables have been fitted correctly and are undamaged.
After each inspection the service schedule shall be filled in. See item 12.3.
Only use Ropox original spare parts as replacement parts. If other parts are used, the
guarantee may become void.
The frame must not be connected to the mains voltage during cleaning.
Do not flush electrical components with water.
Inspections, service and repairs must be carried out by competent personnel
Page 26
13.3 Service schedule, operation and maintenance
14. Trouble shooting
a) The frame seems loose or unstable
The screws assembling the frame have not been securely tightened.
Tighten all screws, cf. mounting instructions.
b) The worktop is not horizontal in relation to the wall
After installation of the frame the worktop will be loaded. This deflection may be balanced
by repeating item 7.5 ”Adjusting the Support arms” of the mounting instructions.
Also check that the legs are vertical – see item 7.2.
c) The frame cannot be height adjusted
1. Check mains and voltage to the control unit and that power is switched on
2. Check cables and plug-in connections between control box and motor/motors. If The control
box makes several click sounds the plug-in connections are not correct
3. Check cables and plug-in connections between control box and control switch
4. Check cable connections between safety stop and control box
5. Check safety stop has not been activated
6. If above does not solve the problem:
− Dismount motor cable/cables from control box
− Dismount netcable from control box and wait min. 5 sec.
− Connect netcable
− Connect motor cable/cables
− Move frame to Lowest/bottom position for “reset”
Service and maintenance
Serial No.:
Date:
Sign:
Remarks:
Service and maintenance
Serial No.:
Date:
Sign:
Remarks:
Service and maintenance
Serial No.:
Date:
Sign:
Remarks:
Service and maintenance
Serial No.:
Date:
Sign:
Remarks:
Page 27
15. CE-marking
The undersigned hereby declares that the following products:
Flexi, electrical with 1 motor and 2 legs 60 – 104 cm
Flexi, electrical with 2 motors and 2 legs 105 – 204 cm
Flexi, electrical with 2 motors and 3 legs 205 – 300 cm
all belong to risk class I and conform to the Directives and Standards mentioned below:
DIRECTIVES
The Machinery Directive 2006/42/EC
STANDARDS
DS/EN 12182: 2012 Assistive products for functionally disabled persons General requirements and test methods
DS/EN 14971: 2012 Medical devices – Application of risk management to medical devices
Risk analyses according to the Machinery Directive 2006/42/EC
DS/EN 60335-1: 2012 Household and similar electrical appliances -
Safety – Part 1: General requirements
DS/EN 9999: 2011: Assistive products for functionally disabled persons -
Classification and terminology
DS/EN 1041+A1: 2013: Information supplied by the manufacturer of medical devices
Dato: ___01-12-2016_____
Page 28
16. Complaints
We refer to our general Terms of sale and delivery on our homepage www.ropox.com
ROPOX A/S
Ringstedgade 221
DK – 4700 Naestved
Tel.: +45 55 75 05 00 Fax.: +45 55 75 05 50
E-mail: info@ropox.dk
www.ropox.com
Loading...