Roper RUD1000K, RUD3000K, RUD4000M, RUD4500M, RUD5000K Dimension Guide

Undercounter Dishwasher

®

PRODUCT MODEL NUMBERS OVERALL DIMENSIONS

CABINET OPENING DIMENSIONS

RUD1000K
RUD3000K
RUD4000M

RUD4500M
RUD5000K
RUD5750K

Electrical: 120-volt, 60-Hz, AC-only, 15- or
20-amp. electrical supply. Use copper wire only. A
time-delay fuse or circuit breaker and separate
circuit is recommended.

Water: A hot water line with 20-120 psi
(138-862 kPa) water pressure. Water temperature
must be 120°F (49°C) at dishwasher. Use 3/8" O.D.
copper tubing with compression fitting or flexible
stainless steel braided fill line (1/2" minimum plastic
tubing is optional but not recommended). Use a 90°
elbow with 3/8" N.P.T. external pipe threads on one
end to connect to water inlet valve. Do not solder
within 6" (15.2 cm) from water inlet valve.

Drain: Use the new drain hose supplied with your
dishwasher. If this is not suitable, use a new drain
hose with a maximum length of 12 feet (3.7 m)
that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and
fits the drain connector of the dishwasher. Must
have a high drain loop 20 inches (50.8 cm) above
the subfloor or floor. Connect drain hose to waste
tee or disposer inlet above drain trap in house
plumbing and 20 inches (50.8 cm) minimum
above the floor. An air gap must be used if the
drain hose is connected to house plumbing lower
than 20 inches (50.8 cm) above subfloor or floor.
Use 1/2" minimum I.D. drain line fittings.

Corner installation: Allow 2" (5,1 cm)
minimum between corner wall and dishwasher
opening.

Grommet is required for electrical cable or power
supply cord hole cut in a metal cabinet.

Do NOT install dishwasher over carpeted floor.
Accepts custom door panels:

RUD1000K, RUD3000K, RUD4000M

Accepts custom door and access panels:

RUD5000K, RUD5750K

Power supply line should enter through the right side
of opening in shaded areas.
Power supply line hole-direct wired: 3/4" (1.9 cm)
Power supply line hole-with plug: 1-1/2" (3.8 cm)

Water line should enter through the
left side of opening in shaded areas.
Minimum 1/2" (12,7 mm) hole.

24" (61 cm)

*

20-3/4" (52.7 cm)

23-7/8" (60.6 cm)

33-7/8"

(86 cm) min.

* to front of

door frame

2-1/2"

(6.4 cm)

2-1/2"

(6.4 cm)

10"

(25.4 cm

)

4" (10.2 cm)

4" (10.2 cm)

4"

(10.2 cm)

5" (12.7 cm)

5" (12.7 cm)

2"

(5.1 cm)

2"

(5.1 cm)

34" (86.4 cm) min.*

6"(15.2 cm)

6"(15.2 cm)

24" (61 cm)

24" (61 cm)**

* Measured from the lowest point

on the underside of countertop.

** Minimum, measured from

narrowest point of opening.

Drain hose should enter through cabinet in shaded areas.
Drain hose size: 1-1/2" (3.8 cm)

door panel
(side view)

door panel (front view)

access panel (front view)

22 31/32"
(58.3 cm)

All edges routed to 7/32" (5.6 mm) thickness.
Note: This panel is wider than the door panel.

23 5/16" (59.2 cm)

7/32"
(5.6 mm)

7/32"
(5.6 mm)

3/8"
(9.5 mm)

1"
(25.4 mm)

Note: Access panel is wider than door panel.

18 21/32"
(47.4 cm)

side view

door
closed

door
pivot

door
opened

access
panel



Cut door panel to clear access
panel when door is in open
position .

CUSTOM FRONT PANEL DIMENSIONS

4 7/16"

11.3 cm

(top view)

7/32" (5.6 mm) thick

access panel frame

1/4"
(6.4 mm) min.

maximum weight is
8 lbs (3.6 kg). Heavy
duty door springs
required for door
panels weighing more
than 4 lbs (1.8 kg).

Ref. 3385181

03-09-04

Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.