Roper RGS7646K, RGS7648K Dimension Guide
1"
PRODUCT MODEL NUMBER OVERALL DIMENSIONS
RECESSED AREA AND CLOSET INSTALLATION
EXHAUST VENTING
RGS7646K
RGS7648K
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
front view
** Opening is minimum for closet door. Louvered door with
equivalent air openings is acceptable.
*** 4" minimum from dryer cabinet rear panel to wall is required for
closet installation or non-exhausted installation.
Recessed
front view
* Shelf of cabinet is not permitted
above dryer when non-exhausted
side view
29"
Max.
27-3/4"
Max.
42-3/8"
Ref. 3393136 Rev. A
10-17-02
Gas Dryer
®
3"
3"
48 sq. in.
**
24 sq. in.**
4"***
14"
max.
0" 0"
closet
door
15"*
Maximum length of exhaust
system depends upon the type of
duct, number of elbows and type
of exhaust hood. The maximum
length for both rigid and flexible
duct is shown in the chart.
For exhaust systems not covered
by the exhaust length chart,
check with your Roper dealer or
service center for a dryer manual
Part No. 603197.
MAXIMUM
LENGTH OF
4-INCH DIA.
RIGID METAL
DUCT
MAXIMUM
LENGTH OF
4-INCH DIA.
FLEXIBLE
METAL DUCT
No. of
90°
turns
EXHAUST HOOD TYPE
ABC
A
B
C
2-1/2"
4"
4"
64 FT.
54 FT.
44 FT.
35 FT.
27 FT.
0
1
2
3
4
58 FT.
48 FT.
38 FT.
29 FT.
21 FT.
36 FT.
31 FT.
27 FT.
25 FT.
23 FT.
64 FT.
54 FT.
44 FT.
35 FT.
27 FT.
36 FT.
31 FT.
27 FT.
25 FT.
23 FT.
0
1
2
3
4
28 FT.
23 FT.
19 FT.
17 FT.
15 FT.
Gas supply: Dryer is equipped for use with
NATURAL gas. Dryer can be converted to L.P. gas.
When rigid pipe is used it should be 1/2 inch IPS.
When acceptable to the gas supplier and local
codes, 3/8-inch approved tubing may be used for
lengths under 20 feet. For lengths over 20 feet,
larger tubing should be used. Pipe-joint
compounds resistant to the action of L.P. gas must
be used. If local codes permit, it is recommended
that new flexible metal tubing, design-certified by
AGA or CSA, be used for connecting the appliance
to the rigid gas supply line. (The gas pipe which
extends through the lower rear of the appliance
has 3/8-inch male pipe thread.) An individual
manual shutoff valve must be installed within 6
feet of the dryer in accordance with the National
Fuel Gas Code ANSI Z223.1.
Electrical: A 120-volt, 60-Hz, AC-only, 15- or
20-ampere, fused on both sides of the line. A
separate circuit serving only this appliance is
recommended. A time-delay fuse or circuit breaker
is recommended.
Exhaust venting: Exhaust your dryer to the
outside. four-inch diameter vent is required. Rigid
or flexible metal exhaust vent must be used. Do
Not use plastic or metal foil vent. Exhaust outlet
hood must be at least 12 inches from the ground
or any object that may be in the path of the
exhaust.
Loading...