Roper REX3519PQ Dimension Guide
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
RECESSED AREA AND CLOSET INSTALLATION
EXHAUST VENTING
RES6745P
RES7646K
RES7745P
REX3514P
REX3519P
REX3614P
REX5634P
REX6634P
Electrical: A four-wire or three-wire, single phase,
120/240-volt, 60 Hz, AC-only, electrical supply (or
120/208-volt electrical supply, if specified on the
serial/rating plate) is required on a separate 30-amp
circuit, fused on both sides of the line. Use 10
gauge solid copper wire. A time-delay fuse or circuit
breaker is recommended.
Exhaust venting: Exhaust your dryer to the
outside. Four-inch diameter vent is required. Rigid
or flexible metal exhaust vent must be used. Do not
use plastic or metal foil vent. Exhaust outlet hood
must be at least 12 inches from the ground or any
object that may be in the path of the exhaust.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 8535914
11-16-04
3. Wide Opening Side-Swing Door
4. Wide Opening Hamper Door
1. Small Opening Side-Swing Door
2. Large Opening Side-Swing Door
0
For closet installation with a
door, minimum ventilation
openings in the top and
bottom of the door are
required. Louvered doors
with equivalent air openings
are acceptable.
1. Select the route that will provide the straightest and most direct path outdoors.
Plan the installation to use the fewest number of elbows and turns. When using
elbows or making turns, allow as much room as possible. Bend vent gradually to
avoid kinking. Avoid 90° turns.
2. Determine vent length.
The maximum length of the exhaust system depends upon:
• The type of vent (rigid metal or flexible metal).
• The number of elbows used.
• Type of hood.
See the exhaust vent length chart that matches your hood type for the maximum
vent lengths you can use.
3. Determine the number of elbows you will need.
IMPORTANT: Do not use vent runs longer than specified in the Vent Length Chart.
In the column listing the type of metal vent you are using (rigid metal or flexible
metal), find the maximum length of metal vent on the same line as the number of
elbows.
Electric Dryer
®
* Most installations require a
minimum 5-1/2” (14 cm)
clearance behind the dryer
for the exhaust vent with
elbow. See Installations
Instructions, “Venting
Requirements.”
4"
(10.2 cm)
(1
4"
(10.2 cm)
Louvered style
Vent Length Chart
Number of
90° turn s
or elbows
0Rigid metal
1Rigid metal
2Rigid metal
3Rigid metal
4Rigid metal
Flexible metal
Flexible metal
Flexible metal
Flexible metal
Flexible metal
4"
(10.2 cm)
Typ e of
vent
Box hood style
Box or
Louvered
hoods
64 ft (20 m)
36 ft (11 m)
54 ft (16.5 m)
31 ft (9.4 m)
44 ft (13.4 m)
27 ft (8.2 m)
35 ft (10.7 m)
25 ft (7.6 m)
27 ft (8.2 m)
23 ft (7 m)
Angled style
Angled
hoods
58 ft (17.7 m)
28 ft (8.5 m)
48 ft (14.6 m)
23 ft (7 m)
38 ft (11.6 m)
19 ft (5.8 m)
29 ft (8.8 m)
17 ft (5.2 m)
21 ft (6.4 m)
15 ft (4.6 m)
2.5"
(6.4 cm)
"
"
29"
"
(73.66 cm)
"
1
27
"
(70.5 cm)
"
5 "
4
(14 cm)
2
"
"
1
2
"
"
1. Recessed area
3
2. Side view - closet or confined area
3. Closet door with vents
Loading...