ROOTS Jet E 130, Jet E 170 Operator's Manual

1

Jet E 130 / 170

Operator’s Manual

Jet E 130 / 170

High Pressure Jet Cleaner
Electric

Read this manual completely and understand the

instructions before operating the machine.

“English Version”

230V/50Hz
415V/50Hz

2

Jet E 130 / 170

3

Jet E 130 / 170

P/N: 557340013-00, Rev: F, Date: 08/2018

Prepared by: SN-NPM TD Dept.

Roots Multiclean Ltd. (RMCL) is not liable for any legal claims that
may arise as a direct or indirect result of the contents of this
manual.

Roots Multiclean Ltd.
R.K.G. Industrial Estate, Ganapathy,
Coimbatore - 641 006, India.

IMPORTANT NOTE:

MACHINE DATA

Please fill at the time of installation for future reference:

Model No. - _______________________________

Serial No. - ________________________________

Accessories - ______________________________

Installation Date - ___________________________

Technical specification
Introduction
Customer support system & Annual maintenance contract
Safety instructions
Machine operation
Maintenance

4
5
6
7
9

13

TABLE OF CONTENTS

4

Jet E 130 / 170

TECHNICAL SPECIFICATION

Weight - 60 kg ( for 1 Ph )
Weight - 63 kg ( for 3 Ph )

920 mm

480 mm

950 mm

High Pressure Hose
Type - 2 High Tensile Steel
Wire Braided Hose

Length - 10 m

Electrical Cable
Length - 5 m

Water Inlet Temp - 60 C°

For Single Phase

Discharge - 10 lpm
Water Pressure - 130 bar

For Three Phase

Discharge - 13 lpm
Water Pressure - 170 bar

For Single Phase

Rated voltage - 230 V
Rated current - 14 A
Frequency - 50 Hz
Total power (max) - 3 KW
Rating - S1 continuous duty
Insulation - F class

For Three Phase

Rated voltage - 415 V
Rated current - 9 A
Frequency - 50 Hz
Total power (max) - 5.5 KW
Rating - S1 continuous duty
Insulation - F class

5

Jet E 130 / 170

INTRODUCTION

PREFACE

Dear Customer,

We are pleased with your having chosen the JET E 130/170
machine for your cleaning requirements. Backed by our industry
expertise that spans across two decades, we assure you that the
machine comes with our Roots promise of quality, efficiency and
performance.

We advise you to carefully read through the instructions prior to
the operation of the machine. This manual contains detailed
instructions for the proper operation of the machine, along with
important information regarding its handling, care maintenance
and service needs.

We are sure that you will find the machine and its performance to
your utmost satisfaction. Once again, we thank you for choosing
Roots Multiclean Ltd (RMCL) as a trusted partner for your
cleaning requirements and solutions.

Usage, Handling & Modification

This machine has been exclusively designed for cleaning of
vehicles, machines, factories, masonry etc, to remove stubborn
dirt using pressurized water. Use of the product beyond the
specified scope of functioning is deemed improper and the
manufacturer cannot be held liable for any damages which may
arise due to this.

This machine may be used only by persons who are trained or are
familiar with the machine and are aware of the possible hazards
involved. The appropriate Accident Prevention Regulations as
well as applicable general regulations pertaining to Safety and
Health at the work place must be adhered to by the user.

Modifications made to machine without the manufacturer's
consent will relieve the manufacturer of responsibility and any
possible liability for consequential damage

Notes On Domestic Warranty

Please refer to the Limited Warranty card supplied
al o ng w it h t he m a ch i n e f o r a d di t i o n a l

information. This Warranty Policy is applicable only for the
product sold within India. If the product requires repair or
maintenance work to be performed, please ensure that you get
the machine serviced from an authorised service centre or dealer
of RMCL to ensure that the warranty is not void.

Acceptance of the Machine

On arrival of the machine at the shipping address, please check
for any damage that may have occurred as a result of transit. In
the event of any such damage, the purchaser is bound by
responsibility to send a claim letter to the concerned RMCL
branch/dealer with a copy of the invoice. The letter should be
sent within 24 hours of receipt of the machine.

6

Jet E 130 / 170

CUSTOMER SUPPORT SYSTEM (CSS)

RMCL has a dedicated CSS Team to ensure prompt after sales service support. One call solution for
all your complaints/concerns. Register your complaint or concern through the below toll free
number for hassle free support. The customer support executive registers your complaint/concern
and will keep you updated on the progress ensuring prompt closure.

Toll Free Number:

1800 41 99 77 9

Our timings (Monday to Saturday):

8:00 am to 7:00 pm

CUSTOMER SUPPORT SYSTEM

ANNUAL MAINTENANCE CONTRACT

Customer Support System Process

Customer

CSS Executive

Engineer

Site Location

AMC or Annual Maintenance Contract is a professional and timely maintenance cover offered by
RMCL to its customers. AMC takes care of scheduled and preventive maintenance services.
Equipment under AMC qualifies for agreed scheduled visits during the contract.

Advantages of AMC:

þ

Pan India network presence.

þ

Maximum equipment uptime.

þ

Focus on your business while we take care of your equipment.

þ

Well trained engineers to take care of the equipment.

þ

System driven scheduled periodic maintenance.

þ

Genuine spare parts.

þ

Toll free number assistance for breakdown.

AMC

7

Jet E 130 / 170

Prior to first operation, read the manual carefully and strictly
comply with the instructions contained.

Read Manual

SAFETY INSTRUCTIONS

General Guidelines

Ÿ In addition to the information contained in this manual,

generally applicable legal provisions for S afety and
Prevention of accidents must be adhered to.

Ÿ Please go through the manual and the instructions contained

herein carefully, even if you possess prior experience in
operating similar cleaning equipment.

Ÿ Schedule some time for the careful and through perusal of

the manual contents .

Ÿ The responsibility of all persons in the working area fall upon

the operator of the machine.

Ÿ No persons, children included, should be allowed within the

zone of danger.

Ÿ The warning and instruction plates attached to the machine

carry important advice on safe operation of the machine.

Ÿ Lost or illegible stickers must be replaced at the earliest.
Ÿ Prior to operation of the machine, the operator must ensure

that the machine and its working implements are in proper
and safe operating condition.

Ÿ Machines with identified and known defects must not be

used.

Ÿ Adherence to the above general instructions will help avoid

the operator from having to read the manual while operating
the machine.

Ÿ This machine must only be used for the manufacturer’s

approved application as described in this manual.

Ÿ The machine must be kept clean and in good condition, if any

parts are damaged they shall only be replaced by an approved
part by the manufacturer, its service agent or a similar
qualified person in order to avoid a hazard.

Ÿ Only genuine accessories and spare parts provided with the

machine or those approved by the manufacturer should be
used. All repairs must be performed by a qualified service
agent.

Ÿ It is important that operators and all persons

likely to u s e t h e m a chi n e fam i l iar i z e
themselves with all accessories and controls,
as well as their functions, before commencing
operation.

Use only genuine spare parts as specified by the
manufacturer. Use of brushes other than those
indicated may affect safety.

Never touch the mains plug with wet hands.

Safety during Jet Cleaner operation

Ÿ Always switch on the machine with trigger in open condition.
Ÿ Check flow of water to the filter inlet (2 - 3 bar gravity

pressure recommended).

Ÿ The machine may be operated by qualified personnel only.
Ÿ The machine may be used for cleaning only such surfaces that

have been approved by the owner or the authorized
representative.

Ÿ The operator must use the machine in accordance to its

intended fields of application.

Ÿ Th e m a chine must be unpacked and ass embled in

accordance with these instructions before connecting to the
electrical supply.

Ÿ This machine should always be connected to a fully earth

power supply of the right voltage and frequency.

Ÿ When working on the electrical system, always disconnect

the cable.

Ÿ Keep the power supply cord away from moving parts.
Ÿ Regularly check the power cord for damages, such as cracks

or aging. If it is damaged, the cable must be replaced before
further use.

Ÿ It is not permitted to use aggressive and corrosive cleaning

agents.

Ÿ Never use excessive foaming or highly corrosive cleaning

solutions.

Ÿ Ensure all parts are fitted properly before operation.
Ÿ Check minimum fuse strength of the socket.

All paragraphs in this manual referring to you personal safety, the
safety of your machine and the environmental protection are
attributed one of the following warning symbols:

Safety provisions in dangerous situation caused by misuse
inaccurate adherence of instruction or prescribed work routine.

Safety Provisions (persons and goods)

Due to use of substances representing an inherent danger to
health of environment.

Ecological Hazard (the environment)

Important information on handling the machine in order to
maintain operability.

Caution (the machine)

SAFETY & WARNING SYMBOLS

8

Jet E 130 / 170

SAFETY INSTRUCTIONS

Ÿ Make sure that the line cords are not damaged by running

over, pinching, dragging , etc.

Ÿ The machine must not be used unless the line cords are in

proper condition.

Ÿ When replacing coupler plugs of line cords or connecting

leads, splash-proof protection and mechanical strength must
be guaranteed.

Ÿ Protect the cable from heat, oil and sharp objects/edges.
Ÿ Unsuitable electrical extension cables can be hazardous. Only

use electrical extension cables outdoors which have been
approved and labeled for this purpose and have an adequate
cable cross - section.

Ÿ Do not operate the machine at low temperature and above

o

60 C.

Ÿ All current conducting materials in the working area must be

protected from jet cleaner.

- Do not clean the machine by means of vapour jet or

high pressure cleaning equipment. Do not allow
water to penetrate into the electrical parts.

-Do not operate the machine in or around an explosive
environment.

DO NOT USE THE MACHINE DIRECTED AT THE
PERSONS, ANIMALS, LIVE ELECTRICAL EQUIPMENT
OR THE MACHINE ITSELF.

- Only qualified personnel must perform any work related to
maintenance and repair on the machine

- Turn the machine off before cleaning and maintenance, while
replacing parts.

Transport

In o rder for easy transpo rtation of t he mach ine, it i s
recommended to tip the machine as shown in the figure.

9

Jet E 130 / 170

UNLOADING

MACHINE OPERATION

Unpacking & Handling

This machine has been exclusively designed for high pressure
cleaning. The machine can be used at factories, masonry and to
clean vehicles, machines etc,

Ÿ Remove the fastening straps, open the package and unscrew

the J hook and move the machine from the pallet.

Ÿ To save packing space and to ensure the safety of the machine

during transporting, the machine comes to you with its
handle, gun, lance, hose and Accessories in dismantled
condition.

1. Machine Unit

2. Handle assy

3. Lance

4. Gun

5. High pressure hose assy

2

4

Ÿ Ensure that the listed parts are present as shown and identify

them in order to understand the assembly instructions.

1

3

5

Identification of Main Parts

1. Starter

2. Motor assy

3. Pump assy

4. Pressure adjustment knob

5. Solution adjustment knob

6. Thermal valve

7. Gun

8. Lance

9. Tray

10. Handle assy

11. High pressure hose

12. Cable assy

13. Wheel

14. Filter assy

5

4

6

13

14

12

11

10

8

9

7

1

2

3

10

Jet E 130 / 170

MACHINE OPERATION

Before Operation - Assembly

Ÿ Insert the handle assembly into the machine and secure them

by screw (2 Nos), washer (4 Nos) & domed cap nut (2 Nos) &
with the help of tools.

Breather

with dip stick

Ÿ To avoid the oil leakage during the transportation, dummy

cap placed in breather position.

Ÿ Before operate the machine, remove the dummy cap and

replace the breather with dip stick.

Ÿ Fit the lance with the trigger with hand tight.

Ÿ Connect one end of the hose with Pump outlet and another

end of the hose with trigger by hand tight.

Ÿ Adjust the nozzle for required angle of water spray.

Min

Max

Operating & Indicator Elements

A - ON Switch ( Green color )

B - OFF Switch ( Red color )

C - Thermal valve
To avoid wear out of O rings, seals of pump, the thermal valve is
provided to eject the hot water from the pump when it is running
in idle condition.

D - Pressure adjustment knob
It is used to adjust the pressure of the outlet water.

E - Trigger lever
It is used operate the trigger.

F - Oil level indicator
To show the oil level of the pump.

o

Oil to be used - SAE 15W40 grade for below 40 environmental
temperature.

o

Oil to be used - WD751WD90 grade for above 40 environmental
temperature.

Oil capacity - 300ml

The level of oil should not come below the Red color
mark.

G - Breather with dip stick
It is used to refill the oil in pump.

E

A

B

F

G

C

D

11

Jet E 130 / 170

MACHINE OPERATION

Ÿ Switch on the machine

Ÿ Connect the fresh water supply to

the filter.

E n s u re t ha t t h e i n fe e d w a t e r i s c l e a n .

DO NOT USE HOT WATER

Ensure to bleed the residual air before starting the
machine. Release the safety lock and press the trigger to
bleed the air.

Ÿ Connect the cable to main power.
Ÿ The machine should only

be connected to a mains power supply equipped with an
adequate earth connection.

Ÿ Release the safety lock and pull

the lever.

After the operation hold the safety lock in trigger for
safety.

Ÿ Adjust the pressure adjustment

knob for your usage

End of cleaning

For Solution

Ÿ Switch OFF the mains power.
Ÿ Stop the water supply for filter inlet.
Ÿ Bleed the residual air from the system by pressing the trigger

for a few seconds.

Ÿ Mount the gun & hose on its place.
Ÿ Clean the filter.

Ÿ Connect the solution tank to the

solution inlet through the hose.

Ÿ Adjust the solution control knob for

usage.

There is a provision to use detergent for cleaning purpose

Ÿ For solution applying, just pull the

nozzle forward.

12

Jet E 130 / 170

MACHINE OPERATION

Accessories

ACCESSORY

Description

Application

Turbo Nozzle Assy

Rotating Brush Kit

Drain Cleaner Kit

Foam Dispenser Kit

Floor Cleaner kit

This accessory has a so
brush which can be used to
clean cars, floors, walls and
the like.

This accessory has a turbo
nozzle which forces out
water in a spiral moon,
used to clean heavy dirt.

This accessory has a long
pipe with a special nozzle,
u s ed t o c l e an d ra in s ,
trenches, pipes, etc.

This accessory is used to mix
cl e an i n g s ol u  o n w i t h
water, handy tool for car
washing.

This accessory is used to
clean special surface floors
like les or industrial floors.

13

Jet E 130 / 170

MAINTENANCE

Filter cleaning

Nozzle

Maintenance Schedule Daily Weekly

Every

500 hrs

Clean nozzle

a

Clean filter

a

Check cable for damage

a

Check hose for damage

a

Remove the strainer & clean

a

Check oil level

a

Oil change
(Initial change in 50 hrs)

a

Before undertaking the cleaning of machine, switch off
the machine and unplug from the electrical supply.

Ÿ After machine operation, open the bottom cap and empty

the filter.

Ÿ Remove the strainer and clean it for clogging.

Ÿ After machine operation, clean the nozzle with pressurized

air, for any blockage.

Do’s & Don’ts

Do’s

Ÿ The machine must be disconnected from the mains supply

(by pulling the plug out) before cleaning the machine and for
maintenance.

Ÿ Use only the accessories recommended as per the instruction

manual. Usage of any other accessories can cause safety
problems.

Ÿ Periodically inspect the power cord for possible damage. A

damaged power cord must be replaced.

Ÿ Regularly clean the filter.
Ÿ Periodically change the oil for lubrication.
Ÿ Operator must wear hand gloves during machine operation.
Ÿ Always place the machine in even surface.
Ÿ Always lock the safety lock in gun, whenever the machine not

in use.

Don’ts

Ÿ Do not use the machine without water.
Ÿ Do not place the machine over the power

cable.

Ÿ Do not leave the machine connected to the power supply

when not in use, always remove the plug from the mains
socket.

Ÿ Do not use the machine near current conducting materials.
Ÿ Do not use the machine without oil.
Ÿ Do not use the machine pointing against persons, animals

and the machine itself.

Ÿ Do not operate the machine at low temperature and above

o

60 C.

Troubleshooting

Problem Possible Fault Remedy

Check cable for damage

Check the voltage of power
supply

clean nozzle

Replace nozzle

Filter clogged Clean filter

Poor water supply Check water supply

Air block in pump

Air block in lance

Air block in hose

Connections

Gun

Inlet

Filter

No power

Machine fails
to start

problem with nozzle

Pressure does
not build up

Continuously press the gunAir Block

Check tightness of the

fittings.

Water leak

14

Jet E 130 / 170

NOTES

15

Jet E 130 / 170

NOTES

Roots Multiclean Ltd.

R.K.G. Industrial Estate, Ganapathy, Coimbatore - 641 006, India.

Phone: [phone], E-mail: [e-mail]
Web: rootsmulticlean.in,
Toll Free: 1800 41 99 77 9