Roost RSW200 Users Manual

Roost User Manual RSW-200 Transmitter Module

User Guide Version: 2

Publication date: March 28, 2017

©2017 Roost, Inc. All rights reserved. The
The Wi-Fi Certified Logo is a logo of

owners. See www.getroost.com/patents for a list of

No part of this publication may be stored,
electronic or otherwise,
Roost, Inc. Requests for permission to store,

1) Compatibility

2.4GHz Band ONLY

2) FCC Notice to OEM

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause
interference that may cause undesired operation.

CAUTION:
Changes or modifications to this unit not
this equipment.

Note: This equipment has been tested and
15 of the FCC Rules. These limits are designed to provide
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
used in accordance with the instructions,
is no
interference to radio or
encouraged to try to correct the interference

Radiation Exposure Statement:

uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between
radiator and your body.

OEM Warning: The modular transmitter must be equipped with either a permanently affixed label or must

be capable of electronically displaying its FCC identification number – FCC ID: 2AE5A-RSW200. If the FCC
identification number is not visible when the module is installed inside another device, then the outside of
the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AE5A­RSW200.” Any similar wording that expresses the same meaning may be used. The Grantee may either
provide such a label, an example of which must be included in the application for equipment authorization,
or, must provide adequate instructions along with the module which explain this requirement. In the latter

Roost, Inc.
955 Benecia
Avenue
Sunnyvale, CA 94085

[e-mail]

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

1.

Reorient the Roost Smart Monitor

2. Consult getroost.com/support for help

whether or not for a charge or other or no

harmful interference, and (2) this device must

television reception, which can be determined

Wi-Fi Alliance®. All other logos and trademarks

This equipment complies with the FCC radiation exposure limit set forth for an

Roost™ word mark and logo are trademarks of

applicable patents and/or patent applications.

reproduced, transmitted or distributed, in whole or

reproduce, transmit or distribute materials may be made to the following address:

expressly approved by Roost, Inc. could void the user’s authority to operate

found to comply with the limits for a Class B digital device, pursuant to part

reasonable protection against harmful

may cause harmful interference to radio communications. However, there

by one or more of the following measures:

Roost, Inc.

are the property of their respective

in part, in any manner,

consideration, without the prior written permission

accept any interference received, including

interference in a

by turning the equipment off and on, the user

of

is

and

case, a copy of these instructions must be included in the application for equipment authorization.

3) ISEDC Notice

This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s).
Operation is subject to the following conditions:



This device may not cause harmful interference.



This device must accept any interference received, including interference that may cause undesired operation of the

device.

Cet appareil est conforme à Industrie Canada une licence standard RSS exonérés (s). Son fonctionnement est soumis aux
deux conditions suivantes:



Cet appareil ne doit pas provoquer d’interférences



Cet appareil doit accepter toute interference recue, y compris les interferences pouvant provoquer un functionnement

indésirable de l’appareil..

Radiation Exposure Statement:

This equipment complies with the IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the
radiator and your body.

Enonće d’exposition aux ravonnements:

Cet équipment est conforme aux limites d’exposition aux rayonnements ioniques
RSS-102 Pour un environnement incontrôlé. Cet équipement doit être installé et utilisé avec un Distance minimale de 20 cm
entre le radiateur votre corps.

OEM Warning: The modular transmitter must be equipped with either a permanently affixed label or must

be capable of electronically displaying its ISEDC identification number – IC: 20891-RSW200. If the ISEDC
identification number is not visible when the module is installed inside another device, then the outside of
the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter Module IC: 20891-RSW200.”
Any similar wording that expresses the same meaning may be used. The Grantee may either provide such
a label, an example of which must be included in the application for equipment authorization, or, must
provide adequate instructions along with the module which explain this requirement. In the latter case, a
copy of these instructions must be included in the application for equipment authorization.

4) Safety Information

WARNING: Do not expose this Roost RSW-200 transmitter module
expose to excessive humidity, rain,
degrees F for best results.

to excessive heat, direct sunlight, or fire. Do

not

moisture or other liquids. Store at room temperature between 40 and 80

WARNING: Keep out of reach of children. Ingestion hazard. Harmful if swallowed.

5) Disposal Information

The Roost RSW-200 Transmitter Module Must be Recycled or Disposed of Properly.

When the Roost RSW-200 Transmitter module is no longer
guidelines in accordance with applicable

functional, please dispose of it

regulations for your country. In most countries,

properly, following

the

electronic printed circuit boards

must be recycled.

6) No Lifesaving Uses of the Services

The

Roost RSW-200 Transmitter module
and the Smart Monitor software may be collectively referred to as the “Services”.
alarm. The apps and device software are intended to be

, Monitor app (including mobile and web applications), the Smart Monitor device,

The Roost Smart Monitor APP is not an

accessed and used for non-critical information

and control of