>> assembly instructions
room essentials
DPCI # 249 - 05 - 0102 (Black Woodgrain)
DPCI # 249 - 05 - 0105 (Espresso)
6 drawer dresser
92336
G
1
FREE!
WEWILLHELPYOU!
Do not go back to your store!
Missing or Damage Parts? Have Questions about Assembly?
The store where you made this purchase does not stock parts for this item.
If you needs parts (damaged or missing) or have questions about assembly,
please call our toll free support line. All orders normally ship within 24 hours.
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service.
For faster service, have the style number and DPCI number ready
when calling.
2
before you begin
tools needed
Congratulations on your latest Target purchase
All you need to do is follow our simple instructions and you'll be on your way to transforming your
Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
room in no time. Good luck - though we're confident you won't need it.
1. Check for damaged or missing parts. Please call 1-855-MYTGTHOME (855-698-4846) for parts and service. Please reference DPCI#
249 - 05 - 0102 (Black Woodgrain)
249 - 05 - 0105 (Espresso)
2. Use the carton as a worksurface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
4. Two people are required for assembly.
3
products available
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
2
table of contents
3
5
6 - 7
8
9 - 31
32
34
33
customer service information
introduction
parts list
hardware
how to use the cam lock system
assembly
specification sheet
information sheet
QUESTIONS?
4
G
left drawer side
right drawer side
07531
08848
EA
IE
JD
LB
PC
PD
FD
HD
00471
03077
00470
6
6
6
6
2
6
1
1
1
2
4
1
1
1
drawer back
drawer bottom
back panel
drawer front
bottom panel
base rail
top panel
top rail
rail
left end panel
right end panel
divider panel
ITEM DESCRIPTION QUANTITY
08848
07531
00471
03077
EA
LB
00470
FD
HD
PC
IE
PD
JD
PC
PD
08848
G
5
x10
25241
x36
20209
x18
21812
x10
31686
x12
25233
x4
25266
x2
25610
x18
26027
x12
26214
x18
26020
x12
31685
x5
12754
x24
20228
x40
10401
x6
13414
short flat head screw
corner bracket dowel pin
spacer
machine screw
long flat head screw connector bolt long 1/4" screw
large cam
small cam
drawer fastener
short 1/4" screw
Rectangular foot
flat head screw
panel clips
hardware
6
x12
41407
x1
97642
x22
31570
x2
94073
x1
88060
drawer glide
cam bolt
allen wrench
wall attachment strip
Drawer Tip Warning Label
hardware
7
CORRECT
NOT
CORRECT
5
180°
1
2
3
4
6
how to use the cam lock system
8
2.
Press the drawer bottom (with the finished side up) into the grooves on the drawer back.1.
Paper overlays the slot, but it has a slit so drawer bottom inserts well.
step 1 drawer assembly - attach drawer bottom to back
03077
07531
nish side up
x 6
fi
paper
9
x24
20228
03077
00471
07531
00470
x 6
step 2 drawer assembly - attach drawer side
drawer fastener
Align holes at back of the drawer sides, with the holes on the drawer back.1.
Tap drawer fasteners into place with a hammer.2.
10
x12
31570
step 3 drawer assembly - insert cam bolts
1. Screw cam bolts into the drawer front. Cam bolts must be screwed down flush.
cam bolt
EA
x 6
11
x1
88060
x12
31685
CORRECT
NOT
CORRECT
03077
00470
EA
x 6
00471
finish side up
07531
88060
small cam
3.
step 4 drawer assembly - attach drawer front and insert drawer cams
Place cams in large holes so that the arrow on cam faces the edge of the drawer sides. 1.
Make sure the drawer bottom is completely inserted into the grooves in the drawer front and drawer back, then tighten the cams.2.
Apply drawer tip warning label to the inside of the top drawer
Drawer Tip Warning Label
12
x24
10401
step 5 drawer assembly - attach panel clips
Place back panel clips as shown and press the thin tabs between the back panel and the groove. 1.
Tighten the screws but be careful not to over tighten.2.
00471
03077
00470
EA
07531
x 6
1
0
"
1
0
"
panel clips
13
x20
20209
dowel pin
step 6 case assembly - insert dowel pins
Press dowel pins into the holes at the end of the 4 rails (PD) and on the top side of the 2 rails (PC) as shown on the picture. 1.
PD
x2
x4
PC
14
NOT
CORRECT CORRECT
x8
20209
x6
25233
x6
13414
x4
31686
dowel pin
step 7 case assembly - insert dowel pins and cams
Tap the dowel pins into the larger holes at the ends of edges of the bottom panel and base rail. 1.
Place the large cam into the holes on the bottom panel.2.
Make sure the arrow on the cam is toward the edge of the panel.3.
Use the short flat head screws to attach the long side of the corner brackets to the base rail (JD) and 2 rails (PD) as shown on the picture.4.
PD
x2
IE
JD
corner bracket
large cam
short flat
head screw
15
x2
20209
CORRECT
NOT
CORRECT
x2
31570
x2
31686
FD
dowel pin
step 8 case assembly - insert cams and dowel pins
4.
Tap the dowel pins into the larger holes at the top and bottom edges of the left end panel.1.
Place the large cam into the holes on the left end panel. 2.
Make sure the arrow on the cam is toward the edge of the panel.3.
Screw the cam bolts into the left panel. Cam bolts must be screwd down flush.
cam bolt
large cam
16
x3
41407
x9
21812
x9
26027
FD
t
o
p
bottom
back
spacer
front (finished edge)
drawer glide
1/4" screw
front of glide
front screw location
back screw location
6.
Fully extend drawer glides to the front.1.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide, 2.
then through the spacers and into the holes on the panel.
Tighten screws but do not over tighten.3.
Close slide until the front hole is visible through the oval slot on the glide.4.
Place 1/4" screws through the hole in the slot and through the spacer.5.
Tighten screw but do not over tighten.
step 9 case assembly - attach drawer glides.
17
NOT
CORRECT CORRECT
x2
20209
x2
31686
x2
31570
dowel pin
step 10 case assembly - insert cams and dowel pins
4.
Tap the dowel pins into the larger holes at the top and bottom edges of the right end panel.1.
Place the large cam into the holes on the right end panel. 2.
Make sure the arrow on the cam is toward the edge of the panel.3.
Screw the cam bolts into the right panel. Cam bolts must be screwd down flush.
cam bolt
HD
large cam
18
x3
41407
x9
21812
x9
26027
step 11 case assembly - attach drawer glides
drawer glide
spacer 1/4" screw
front screw location
front of glide
front (finished edge)
top
back
bottom
6.
Fully extend drawer glides to the front.1.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide, 2.
then through the spacers and into the holes on the panel.
Tighten screws but do not over tighten.3.
Close slide until the front hole is visible through the oval slot on the glide.4.
Place 1/4" screws through the hole in the slot and through the spacer.5.
Tighten screw but do not over tighten.
back screw location
HD
19
NOT
CORRECT CORRECT
x4
20209
x2
31686
dowel pin
large cam
3.
Tap the dowel pins into the larger holes at the top and bottom edges of the divider panel. 1.
Place the large cam into the holes on the divider panel. 2.
Make sure the arrow on the cam is toward the edge of the panel.
step 12 case assembly - insert cams and dowel pins
G
20
x6
41407
x18
26020
short 1/4"
screw
G
back screw location
drawer glide
back
bottom
front (finished edge)
t
o
p
front screw location
front of glide
step 13 case assembly - divider panel
Fully extend drawer glides to the front of the divider panel. 1.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide. 2.
Tighten screws but do not over tighten.3.
Close slide until the front hole is visible through the oval slot on the glide.4.
Tighten screw but do not over tighten.5.
21
x6
31570
x4
25266
3. Line up dowel pins with the holes in the top panel, then tighten screws.
long flat head screw
cam bolt
front edge
Screw the cam bolts into the top panel. Cam bolts must be screwed down flush. 1.
Place long flat head screws through holes on top rail. Make sure the finished side of the rail is facing the front.2.
finished
step 14 case assembly - attach top rail
PC
LB
PC
fin
ish
e
d
fr
o
n
t
e
d
g
e
22
x2
25610
x1
97642
connector bolt
allen wrench
2.
Place the divider panel end over the bottom pannel.1.
Use the allen wrech to install connector bolts.
step 15 case assembly - attach divider panel to bottom panel
IE
finished front edge
G
23
step 16 case assembly - attach rail and panel
Two people are needed for this assembly step. 1.
Place the cam bolts from the left panel into the holes on the bottom panel and tighten the cams. 2.
Place the ends of the two rails into the holes and hold in place.3.
IE
G
FD
PD
finished
front edge
PD
24
3.
Two people are needed for this assembly step. 1.
Place the cam bolts from the right panel into the holes on the bottom panel and tighten the cams. 2.
Place the ends of the two rails and base rail into the holes and hold in place.
step 17 case assembly - attach rail and panel
IE
PD
HD
PD
PD
PD
G
FD
JD
25
3.
Attachthebackpanelbyslidingitintothegroovesinthesideandbottompanel.1.
Attachthetoppanelbypressinginontothebackpanelandbyinsertingdowelpinsandcam boltsintotheholes.2.
Makesuredowelpinsandcamboltsarecompletelyinsertedandthentightenthecams.
step 18 case assembly - attach back panel and top panel
HD
LB
08848
G
08848
FD
08848
26
x10
25241
x5
12754
front
edge
1/4"
back
edge
1"
not necessary.
Repeat step 1-2 for the remaining 2 feet.
Place a rectangular foot on the bottom of the side panel at a distance from the front edge of 1/4" and 1" from the back edge, centered on the width of the panel-side.1.
Place the screws through to two holes and gently screw them onto the side panel. Make sure to fasten the screws, but be careful not to over tighten.2.
3.
flat head screw
rectangular foot
IMPORTANT:
When placing this unit on thick carpet,
the addition of 5 rectangular feet is
required to improve stability.
For floors with a hard surface or low
pile carpeting, the additional feet are
step 19 case assembly - attach rectangular feet
27
x16
10401
x2
25233
panel clips
3.
Place back panel clips as shown and press the thin tabs between the back panel and the groove. 1.
Tighten the screws but be careful not to over tighten.2.
Add screws into bracket.
step 20 case assembly - attach back panel clips and brackets
08848
FD
08848
HD
IE
JD
90°
90°
3"
4"
4"
short flat head screw
28
x4
25233
short flat head screw
step 21 case assembly - attach corner bracket
Fasten the middle rail (with corner brackets) to the panels with the short flat head screw.1.
08848
FD
LB
HD
IE
G
08848
29
1
32
1 1/5"
x2
94073
wall attachment strip
LB
08848
FD G
HD
IE
08848
IMPORTANT.
The screw supplied together with the wall attachment
strip is to be used only for fixing the wall attachment
strip to the furniture.
In addition to this, you will need to choose a screw or
fitting which is suitable for securing the bracket to the
kind of walls you have. If you are unsure about what type
of screw to use contact your local hardware store.
Wall attachment strips are requred to be installed.
step 22 case assembly - mount wall attachment strips
Place the dresser in the desired position against the wall. Mark the locations of 1.
the TWO wall attachment SLOTS at the top of the DRESSER.
MEASURE down 1 1/5" from the mark at the top of the case and attach the two 2.
wall STRIPS with washers and screws.
Note - The washers and screws for wall attachment should be purchased from
a hardware store to suit the type of wall.
Pass the wall attachment strips through the slots at the top back of the case, 3.
and attach them to the underside of the DRESSER top with the screws and
washers that are included in the PACK.
30
x12
26214
4.
machine screw
Slide groove on drawer sides over the drawer glide.1.
Pull the slide forward until the threaded hole on the glide aligns with the hole in the drawer side. 2.
Attach glide screw from inside the drawer box into the drawer glide.3.
Second hole on drawer slide is not used.
step 23 case assembly - install drawers into case
EA
EA
LB
HD
EA
EA
EA
EA
31
lbs
kg9
20
lbs
kg60
132
South Boston, VA 24592
3 YEAR WARRANTY:
All Tvilum furniture is warranted to the original
purchaser at the time of purchase and for 3
years after the purchase date. We warrant to
you, the original purchaser, that our furniture
and all furniture parts and components are free
of defects in material or workmanship. The
word “defects” as used in this warranty is
defined as any imperfections which impair the
use of the furniture.
Our warranty is expressly limited to the replacement or repair of furniture parts and
components and Tvilum will have a reasonable
amount of time to remedy said defect. This
warranty applies under conditions of normal
use. The warranty does not cover defects
caused by improper assembly or disassembly
defects occurring after purchase due to
intentional damage, product modifications,
exposure to the elements, accidents, misuse,
abuse or negligence and labor or assembly
costs.
All implied warranties, including the warranty of
merchantability shall not extend beyond the
duration of the written warranty stated above.
Tvilum liability is expressly limited to the costs
of material for repair or replacement of
defective goods and in no event will Tvilum be
liable for incidental or consequential damages
resulting from use of the product. Some states
do not allow limitations on how long an implied
warranty may last or the exclusions or
limitations of incidental or consequential
damages, so the above limitations and
exclusions may not apply to you.
This warranty gives you specific legal rights
which may vary from state to state.
Any claims made under this warranty must be
presented in writing to:
Tvilum
2195 Philpott Road
specification sheet
32
NOUS�VOUS�GARANTISSONS�
que ce produit:
A été évalué pour toute substance dangereuse,
pour garder un environnement sain à l’intérieur
de votre maison
Est fabriqué à partir de foresterie durable
Ce mobilier est certifié PEFC
Est sûr pour votre intérieur
le produit a passé les contrôles de sécurité
et a été approuvé
Contient un minimum de 25 % de
matériel recyclé postconsommation.
Apprenez-en plus sur www.tvilum.com
THIS�PRODUCT
will ensure you
A product tested for harmful substances
Helps to maintain healthy indoor climate
Wood from sustainable forestry
The furniture is PEFC-certified
Safe furniture for use in your home
The furniture has been safety tested and approved
Minimum 25% post consumer recycled materials
Read more at www.tvilum.com
33
4 drawer dresser
products available
6 drawer dresser
34
35
Loading...