VideoinstructionasHelptoassembly,
scantheQRcodeandseethevideo.
DPCI # 249-05-0419 (Virginia Walnut)
92380 &
room essentials
4 Drawer dresser w/ door
DPCI # 249-05-0418 (Black Woodgrain)
>> assembly instructions
1
FREE!
WEWILLHELPYOU!
Do not go back to your store!
Missing or Damage Parts? Have Questions about Assembly?
The store where you made this purchase does not stock parts for this item.
If you needs parts (damaged or missing) or have questions about assembly,
please call our toll free support line. All orders normally ship within 24 hours.
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service.
For faster service, have the style number and DPCI number ready
when calling.
2
before you begin
tools needed
Congratulations on your latest Target purchase
All you need to do is follow our simple instructions and you'll be on your way to transforming your
Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
room in no time. Good luck - though we're confident you won't need it.
Check for damaged or missing parts. Please call 1-855-MYTGTHOME (855-698-4846) for parts and service. Please reference1.
DPCI # 249-05-0418 (Black Woodgrain)
DPCI # 249-05-0419 (Virginia Walnut)
Use the carton as a worksurface to prevent product damage during assembly.2.
Gather all tools prior to assembly.3.
Two people are required for assembly.4.
3
table of contents
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
QUESTIONS?
2
3
5
6 - 7
8
9 - 32
33
34
35
customer service information
introduction
parts list
hardware
how to use the cam lock system
assembly
adjustment of hinge
specification sheet
information sheet
4
00590
00591
03087
06294
09732
E
F
G
H
I
L
T
W door left
shelf
top panel
bottom panel
right end panel
divider panel
left end panel
drawer front
back panel
drawer bottom
drawer back
left drawer side
right drawer side 4
4
4
4
2
4
1
1
1
1
1
2
1
ITEM DESCRIPTION QUANTITY
G
L
T
09732
09732
W F
T
I
H
E
00590
06294
03087
00591
5
x2
10601
x1
10901
x8
11042
x12
20203
x24
20228
2
5
p
c
s
x2
23006
x8
25233
x11
23010
x6
25215
x16
25502
x18
26040
x5
26228
x18
31570
x18
31683
x3
50505
x5
81009
x2
91405
x2
96203
x5
26234
x5
32205
x2
25610
hardware
garment rod
holder
cover
shelf pin
dowel pin drawer fastener
nails
large head nails
flat head screw
cam bolt
cam
hinge
handle L-plate
stopper
long feet screw
drawer screw
short screw
handle screw
short flat head screw
short feet screw
connector bolt
6
x1
72501
x1
94072
x4
41649
x5
65806
x2
94073
x3
52114
x1
88060
x1
97642
hardware
drawer glide
rectangular foot
garment rod
wall attachment strip
stabilizer
door hinge
Warning label
hex wrench
7
5
CORRECT
NOT
CORRECT
180°
123
46
how to use the cam lock system
8
CORRECT
NOT
CORRECT
x10
31683
x12
20203
Arrow
cam
2.
Place the cams into the large holes on G, L and I, so that the arrow is facing the edge of the panel.1.
Insert dowel pins into the small outer holes on the ends of the G,L and I.
step 1 case assembly - insert cams and dowel pins
dowel pin
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
G
L
I
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
9
x3
50505
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
F
3.
step 2 case assembly - insert hinges
Divide hinge by loosening the screw and split hinge part from each other.1.
Place hinge into the correct holes on the left end panel.2.
Tighten screws but do not over tighten.
hinge
10
x10
31570
x5
32205
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
F
L
I
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
H
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
step 3 case assembly - insert cam bolt
Screw cam bolts into the panels F, L and H, cam bolts must be screwed down.1.
Tab short feet screw into panel I with a hammer.2.
cam bolt
short feet screw
11
x16
26040
x8
25233
x4
41649
step 4 case assembly - attach drawer glides
Place drawer glider screws and flat head screw through the correct holes on the drawer slide into the holes on the panels G + H. 1.
Tighten screws but do not over tighten.2.
Repeat this step for each of the remaining glides.3.
drawer glide
screw
G
H
drawer glide screwdrawer glide screw
flat head screw
flat head
screw
drawer glide
12
x2
25215
x2
10601
short flat head screw
Screw the garment rod holder into the panels using short flat head screws.1.
step 5 case assembly - insert garment rod holder
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
F
f
in
is
h
e
d
f
r
o
n
t
e
d
g
e
G
garment rod holder
13
x1
97642
x2
25610
f
i
n
i
s
h
e
d
f
r
o
n
t
e
d
g
e
f
i
n
i
s
h
e
d
f
r
o
n
t
e
d
g
e
L
G
I
f
i
nis
h
ed
f
ront
edg
e
connector bolt
hex wrench
step 6 case assembly - attach top panel and bottom panel to divider panel
Place the cam bolts from top panel L into the holes on the divider panel G.1.
Tighten cams.2.
Use the hex wrench to install connector bolts into I and divivider panel G.3.
14
step 7 case assembly - attach left and right panel
Place the cam bolts from left and right end panels F and H into the holes on the top and bottom panels L and I.1.
Tighten cams.2.
H
f
i
nis
h
ed
f
ront
edg
e
f
i
nis
h
ed
f
ront
edg
e
G
F
I
f
i
n
i
s
h
e
d
f
r
o
n
t
e
d
g
e
L
f
i
nis
h
ed
f
ront
edg
e
15
x2
91405
x4
25215
L-plate
short flat head screw
f
i
n
i
s
h
e
d
fr
on
t
ed
g
e
I
L
H
G
F
step 8 case assembly - attach L-plates
Use short flat head screw to attach L-plate to the right end panel H and in alignment with top panel L, place in center.1.
Use short flat head screw to attach L-plate to the left end panel F and in alignment with top panel L, place in center.2.
16
x5
65806
x5
26234
together with short feet screw 32205, but be careful not to over tighten.
Place rectangular feet 65806 into the holes on the bottom panels I.1.
Place the screws 26234 through holes and gently screw them onto the bottom panel. Make sure to fasten the screws 2.
step 9 case assembly - attach rectangular feet
I
G
F
H
L
rectangular foot
long feet screw
17
x2
23006
2
5
p
c
s
x11
23010
90°
09732
H
I
09732
3
step 10 case assembly - attach back panels
nails
Tab 2 of the large head nails 23010 into the centre of back edge of divider panel G. ONLY HALF WAY IN.1.
Slide the back panels 09732 up (unfinished side up) against the nails and hold smooth with bottom panel I.2.
Attach one nail 23006 in each corner.3.
Attach the rest of nails 23006 all the way arround the edges and 9 pcs 23010 into divider panel G.4.
unfinished side
09732
09732
I
1
unfinished side
09732
H
I
09732
2
large head nails
18
1
32
1 1/5"
x2
94073
wall attachment strip
09732
L
G
F
I
H
09732
step 11 case assembly - mount safety wall attachment strips
IMPORTANT.
The screw supplied together with the wall attachment strip
is to be used only for fixing the wall attachment strip to the
furniture.
In addition to this, you vill need to choose a screw or
fitting which is suitable for securing the bracket to the
kind of walls you have. If you are unsure about what type
of screw to usee contact your local handware store.
Wall attachment strip are required to be installed.
Place the dresser in the desired position against the wall. Mark the locations of 1.
the TWO wall attachment SLOTS at the top of the DRESSER.
MEASURE down 1 1/5" from the mark at the top of the case and attach the two 2.
wall STRIPS with washers and screws.
Note - The washers and screws for wall attachment should be purchased from
a hardware store to suit the type of wall.
Pass the wall attachment strips through the slots at the top back of the case, 3.
and attach them to the underside of the DRESSER top with the screws and
washers that are included in the PACK.
19
x1
94072
x2
26040
step 12 case assembly - attach stabilizer
Place the stabilizer 94702 in between divider panel G and right end panel H. 1.
Place the short screw 26040 through the holes of 94702 and gently screw them into the panels G and H.2.
Tighten screws but do not over tighten.3.
stabilizer
H
F
I
L
09732
09732
G
short screw
20
x1
10901
x8
11042
cover
x2
step 13 case assembly - install shelves and cover
Fix cover to the top panel L to cover the cam holes.1.
Insert shelf pin 11042 in right end panel F and divider panel G. 2.
Place shelves T into the case assembly as shown.3.
Press shelves T down onto the shelf pin.4.
09732
F
I
H
L
G
T
T
09732
shelf pin
21
x1
72501
step14 case assembly - install garment rod
Attach garment rod 72501 into garment rod holder assembled in between left end panel F and divider panel G. 1.
IMPORTANT.
When using garment rod Place Shelves T in bottom.
G
H
I
09732
F
L
T
T
09732
garment rod
22
x3
52114
W
step 15 case assembly - install door hinge
Insert door hinge into the holes on the door W.1.
Tighten screws but do not over tighten.2.
door hinge
23
step 16 case assembly - attach door
Align the holes in hinge and door hinge.1.
Move the door W to perfectly assemble with left end panel F.2.
Tighten screws but do not over tighten.3.
Ajustment of door, see page 33.4.
09732
W
T
T
I
F G
H
L
09732
24
x1
26228
x1
81009
x2
96203
handle screw
09732
W
T
T
I
F G
H
L
09732
step 17 case assembly - attach handle to door and stop to divider panel
Use the handle screw 26228 to attach the handle 81009 to the door W.1.
Attach stops 96203 to the divider panel G.2.
handle
stopper
25
CORRECT
NOT
CORRECT
x8
31570
x8
31683
00590
00591
E
x4
cam
2.
Insert cams 31683 in the large holes on the face of each drawer side. Make sure1.
the arrow on the cam is pointed toward the edge of the drawer side as shown in the detail at left.
Screw 2 cam bolts 31570 into each drawer front E.
step 18 drawer assembly - insert cams and cam bolts
cam bolt
26
x24
20228
Align holes at back of the drawer sides, 00590 and 00591 with the holes on the 1.
drawer back 03087. Make sure the groove on the drawer back is facing the inside of
the drawer. Tap drawer fasteners into place with a hammer.
Repeat these steps for all 4 drawers.2.
step 19 drawer assembly - attach drawer sides to drawer back
00591
03087
00590
drawer fastener
27
06294
finished side up
00591
03087
00590
step 20 drawer assembly - attach drawer bottom
Press the drawer bottom 06294 (with the finished side up) into the grooves on drawer sides 00590, 00591and the back 03087.1.
Paper overlays the groove, but it has a slit so drawer bottom inserts well.2.
Repeat these steps for all 4 drawers.3.
28
step 21 drawer assembly - attach drawer front
Place the cam bolts that are attached to the drawer front E into the holes on the drawer sides.1.
Make sure the drawer bottom is completely inserted into the grooves in the drawer front and back. 2.
Tighten cams.3.
Repeat these steps for all 4 drawers.4.
00590
03087
00591
06294
E
29
x4
81009
x4
26228
handle
00591
06294
00590
03087
E
2.
Use the handle screw 26228 to attach the handle 81009 to the drawer front E.1.
Repeat these steps for all 4 drawers.
step 22 drawer assembly - attach handle to drawer front
handle screw
30
x4
41649
x16
25502
step 23 drawer assembly - attach drawer glides
Place drawer glide on bottom of drawer side and slide forward against drawer front E.1.
Insert drawer glide screws through the hole in the drawer glide and into the drawer side plates. 2.
Tighten screws but do not over tighten.3.
Repeat these steps for all 4 drawers.4.
00591
06294
03087
E
drawer glide
drawer screw
31
x1
88060
E
WF
L
E
E
E
Warning label
3.
Angle the drawer assembly so that the wheels are inserted into the drawer glides on divider panel G and right end panel H.1.
Slide drawer assembly over the drawer glides on divider panel G and right end panel H.2.
Apply warning label 88060 inside top drawer.
step 24 case assembly - install drawers into case assembly and warning label on top panel
32
2.
3.
1.
3.
1.
2.
1.
2.
3.
08799998 -50
33
lbs
kg15
33
lbs
kg10
22
lbs
kg5
11
max.
South Boston, VA 24592
3 YEAR WARRANTY:
All Tvilum furniture is warranted to the original
purchaser at the time of purchase and for 3
years after the purchase date. We warrant to
you, the original purchaser, that our furniture
and all furniture parts and components are free
of defects in material or workmanship. The
word “defects” as used in this warranty is
defined as any imperfections which impair the
use of the furniture.
Our warranty is expressly limited to the replacement or repair of furniture parts and
components and Tvilum will have a reasonable
amount of time to remedy said defect. This
warranty applies under conditions of normal
use. The warranty does not cover defects
caused by improper assembly or disassembly
defects occurring after purchase due to
intentional damage, product modifications,
exposure to the elements, accidents, misuse,
abuse or negligence and labor or assembly
costs.
All implied warranties, including the warranty of
merchantability shall not extend beyond the
duration of the written warranty stated above.
Tvilum liability is expressly limited to the costs
of material for repair or replacement of
defective goods and in no event will Tvilum be
liable for incidental or consequential damages
resulting from use of the product. Some states
do not allow limitations on how long an implied
warranty may last or the exclusions or
limitations of incidental or consequential
damages, so the above limitations and
exclusions may not apply to you.
This warranty gives you specific legal rights
which may vary from state to state.
Any claims made under this warranty must be
presented in writing to:
Tvilum
2195 Philpott Road
specification sheet
34
NOUS�VOUS�GARANTISSONS�
que ce produit:
A été évalué pour toute substance dangereuse,
pour garder un environnement sain à l’intérieur
de votre maison
Est fabriqué à partir de foresterie durable
Ce mobilier est certifié PEFC
Est sûr pour votre intérieur
le produit a passé les contrôles de sécurité
et a été approuvé
Contient un minimum de 25 % de
matériel recyclé postconsommation.
Apprenez-en plus sur www.tvilum.com
THIS�PRODUCT
will ensure you
A product tested for harmful substances
Helps to maintain healthy indoor climate
Wood from sustainable forestry
The furniture is PEFC-certified
Safe furniture for use in your home
The furniture has been safety tested and approved
Minimum 25% post consumer recycled materials
Read more at www.tvilum.com
35
36
Loading...