Room & Board Webster Assembly Instruction

1. Position the full-size frame at desired location in room with the slots in the
rails facing the floor. If the bed will be next to a wall, allow enough room for
a person to stand between the wall and bed.

2. Position one bed end at the end of the full-size frame with pockets facing
the frame. With one person on each side, lift and fit the frame over the bed
end’s lower pockets.

3. Repeat previous step with other bed end. Ensure that all rails are securely
in place.

4. With a person on each side of the twin-size frame, lift it over the upper
pockets of the bed ends. Slip the frame over the pockets on one bed end,
then over the other bed end.

5.To secure the full-size frame, insert a 3/4" screw into the guide hole above
each of the lower rail pockets.

6. Remove the screws from the full-length guard rail. Position the guard rail
on the upper bunk, evenly between each bed end. Slide a C-bracket over
the 3" top rail at each end of the guard rail with the holes facing the inside
of the bed. Position a nut in between the top and bottom holes in each
C-bracket, insert screws and tighten.

7. Remove the screws from the ladder. Position the ladder on the right or
left side of the bed. Place the lower clips over the bottom rail, then put
C-brackets over the 3" top rail. Making sure the ladder is against the bed
end, position nuts between the top and bottom holes of both C-brackets,
insert screws and tighten.

8. Position the 3/4-length guard rail on the same side of the bed as the ladder.
Attach the end of the guard rail to the vertical bed end. Remove the screws
from the 3/4-length guard rail. Slide C-brackets over the 3" top rail at each
end of the rail, with holes facing toward the inside of the bed. Position the
nuts between the top and bottom holes of both C-brackets, insert screws
and tighten.

9. Slide bed into final position.

10. Put full mattress on lower bunk and twin mattress on upper bunk.

Fort Duo Bunk Assembly Instructions

List of parts: 1 - left end

1 - right end

1 - full-size frame

1 - twin-size frame

1 - full-length guard rail with 2 screw/nut assemblies attached

1 - 3/4-length guard rail with 2 screw/nut assemblies attached

1 - ladder with 2 screw/nut assemblies attached

4 - 3/4" screws

Tools needed: phillips screwdriver

Note: Two people are required for assembly. A person on each side of

the bed will be required to lift 100 lbs. to a height of 55".

Directions:

®

ladder

full-size frame
(15 slats)

right end

full-length guard rail

3/4-length guard rail

twin-size frame
(15 slats)

left end

Please keep these instructions for future reference.

1. Follow the warnings on the upper bed end structure. Do not remove
warning label from bed.

2. Always use the recommended size mattress to help prevent the likelihood
of entrapment or falls. For the upper bunk, only use a mattress which is 74"­75" long and 37 1/2"- 38 1/2"wide.

3. Surface of mattress must be at least 5" (127mm) below the upper edge
of guard fences.

4. Do not allow multiple people or children under 6 years of age to use
the upper bunk.

5. Periodically check and ensure that the guard fences, ladder and other
components are in their proper position, free from damage, and that all
connectors are tight.

6. Do not allow horseplay on or under the bed and prohibit jumping on
the bed.

7. Always use the ladder for entering and leaving the upper bunk.

8. Do not use substitute par ts. Contact Room & Board for replacement
parts.

9. Use of a night-light may provide added safety precaution for a child using
the upper bunk.

10. Always use guard fences on both long sides of the upper bunk.

11. The use of water or sleep flotation mattresses is prohibited.

slotted opening

rail pocket

rail/combination piece

guard rail attachment detail

guard rail

nut

slotted screw

Safety Warnings: