Room & Board Nest Crib Assembly Instruction

assembly instructions: moda bed and bunk bed

long guard rail

headboard footboard

List of parts for twin bed

1 – headboard
1 – footboard
2 – bed rails
1 – slat roll
18 – decorative bolts

Directions for bed and bunk

1. Assemble the lower section of the bunk bed first. Use the two headboards as the
bottom panels of the bunk.

Begin here for Twin Bed Assembly. Steps 2-4, Figure 2, Steps 9, 11 and 12.

2. Inser t a wood dowel into the middle hole of each trio of holes on both panels. Screw a

connector bolt into each of the threaded inserts, leaving four or five threads exposed.

ladder

List of parts for bunk bed

( 2 sets of twin bed par ts plus the following)

1 – short guardrail
1 – long guardrail (4 screws enclosed

in cardboard pad on bracket)
1 – ladder
4 – steel pins wrapped with ladder

Hardware

4 – wood dowels
8 – connector bolts
8 – metal collars
28 – wood screws for slat roll

3. Align connector bolts with the holes on the end of a bedrail, slipping bolts through
pre-drilled holes in the bedrail. Repeat on other side. Make sure each bedrail is tight up
against the panel.

4. Through the large hole in the side of the bedrail, slip one metal collar over each
connector bolt. Use the ball end Allen wrench to start tightening each bolt, then switch
to the short end to finish tightening completely.

5. Insert steel pins into the holes on top of the headboards.

6. Place footboards on top of the steel pins and push down until the bottom of the

footboard is resting on top of the headboard.

7. Attach the upper bedrails in the same manner as Steps 1-4 above.

Tools needed

ball end Allen wrench (provided)

MADE IN N ew Yo rk

800.301.9720 | roomandboard.com

4/1/11

8. Place the long guardrail on the wall side of the bed so that the brackets are on the inside
of the bedrail, and attach each bracket with two screws. Place the shor t guardrail on the
front bedrail against one of the footboards. (This allows an opening for the ladder at the
other end.) Screw the short guardrail brackets to the inside of the bedrail.

assembly instructions: moda bed and bunk bed

Directions for bed and bunk continued...

9. Unroll and lay the slatroll inside the bedrails, with the webbing facing up. With the 28 wood screws provided, attach the slats. The first
slat must be 2" from the end of the bedrail. Pull the slatroll taught and secure the other end 2" from the end of the bedrail on that
side; then secure all other slats. The slats should be centered between the bedrails, with a
bedrail. This permits the guardrail bracket to slip in between the slat and the bedrail.

10. Attach the ladder to the bedrail by hooking it over the bedrail.

11. Mattress may be placed with or without a platform board on the slatroll.

12. The two white plastic plugs may be used to fill in the holes on the top of the headboard.

note

Only use a mattress that is 74"-75" long and 37½"- 38½" wide on upper bunk.

Directions for full length (long) guardrail

1. Unscrew and remove existing guard rail mounting brackets from both ends of guard rail. This step needs to be done only with full

length guard rail to prevent headboard from inter fering with installation.

2. Insert guard rail onto bed rail. Once rail is in proper position replace both guard rail mounting brackets, facing inside of bed

rail. Finally, secure guard rail to side rail with two screws in each bracket.

1

⁄8" gap between the end of the slat and the

SAFETY WARNINGS

Ensure thickness of mattress and foundation combined does
not exceed 9½" and mattress is at least 5" below upper edge
of guardrails.

1. Do not allow children under 6 years of age to use the
upper bunk.

2. Use guardrails on both sides of the upper bunk.

3. Prohibit horseplay on or under beds.

4. Prohibit more than one person on upper bunk.

5. Use ladder for entering or leaving upper bunk.

6. If the bunk bed will be placed next to a wall, the guardrail

that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and
the wall.

• Replacement parts, including additional guardrails, may be
obtained from any Room & Board store.

• Follow the information on the warnings appearing on the
upper bunk end structure and on the carton. Do not remove
warning label from bed.

• Periodically check and ensure that the guardrail, ladder and
other components are in their proper position, free from
damage and that all connectors are tight.

• Do not allow horseplay on or under the bed and prohibit
jumping on the bed.

• Do not substitute parts. Contact the manufacturer or dealer
for replacement parts.

• Use of a night light may provide added safety precaution for
a child using an upper bunk.

• The use of water or sleep flotation mattresses is prohibited.

STRANGULATION HAZARD

Never attach or hang items to any par t of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks,
belts and jump ropes.

800.301.9720 | roomandboard.com

4/1/11