Room & Board Moda Crib Assembly Instruction

CRIB A S SEMBLY INSTRUCTION S

For MODA Crib

DO NOT USE POWER TOOLS!

Ste p 1: Lay the B ase Pane l on the floor. Place one of the End Panels
on the left side of the Base Panel so that the silver metal inserts are facing
inward. Use three Decorative Bol ts and Lo ck Washe rs to secure the
End Panel to the Base from underneath the Base Panel, but DO NOT
tighten the Bolts completely yet. Repeat this procedure on the right.

Ste p 2: Attach one of the S i des to the End Panels with four
Decorative Bol ts and Lo ck Washe rs using the enclosed Allen
Wrenc h. Place the Bolts through the end slat of the Side and into the End

Panel, but DO NOT tighten completely.

Ste ps 1 & 2 Attac h End Panels and 1 Side

Ste p 3: Screw a Bolt and Lock Washer in each of the top holes of the 4

middle columns of inserts on the End Panels. Leave the bolts sticking out at
least an inch. This configuration puts the Mattress in the highest position,

which is the height recommended for newborns. To select a lower position,
place the bolts in lower holes. Place the Mattres s Support Platf orm

over the Bolts. The notches in the Platform fit snugly over the Bolts.

Ste p 4: Attach the other Side to the End Panels as in step 2. Now tighten
all 18 Bolts on crib completely.

BOLT + WASHER

BOLT + WASHER

Conversion to To ddler Bed: The crib mattress should be in lowest
position (Bolts in the lowest holes.) Remove the front Side by undoing
what you did in Step 4. Remember to loosen ALL Decorative Bolts
before attempting to remove the Side. Use the bolts and lock washers
you removed to attach the Toddler Rail as in Step 4.

THIS CRIB MAY NOT BE USED A S A TODDLER B ED

WITHOUT A TODD LER RAIL.

Fo r To ddl e r Be d us e , the minimum age shall be no less than 15

months and the maximum weight shall not be greater than 50 lb
(22.7kg). The mattress intended for use on the bed shall be a full-size
crib mattress having minimum dimensions of 51.625 in. (131cm) in
length and 27 ¼ in. (69cm) in width and thickness of no less than 4 in.
(11mm) and not exceeding 6 inches (15cm).

Mainte nance: Periodically check to make sure all screws, bolts and
fastening devices are tight. Before each usage or assembly, inspect crib
for damaged hardware, loose joints, missing parts or sharp edges. DO
NOT use crib if parts are missing or broken. DO NOT substitute parts.
DO NOT make any alteration to this crib.
Cle aning: Mix a mild solution of gentle dishwashing liquid and water,
apply to crib surface using a soft, clean cloth, then dry all surfaces with
a soft, dry cloth. NO ABRASIVES, SCOURING PADS, STEEL
WOOL, OR COARSE RAGS should be used to clean this fine furniture.
Sto rag e : A Plasti c Po uch is attached to the crib spring for storage of
the assembly instructions for future referral. After completing the
assembly, you are advised to read and be aware of all WARNINGS,
CAUTIONS, CLEANING, STORAGE AND MAINTENANCE notices
contained herein. We caution you not to place excess hardware in the
plastic pouch as it could present danger to a child if retrieved and it
could also puncture the crib mattress. When storing crib, use CAUTION
as extreme temperature or humidity changes could be harmful.

PA RTS INCLU DED IN CA RTON

1 – BASE PANEL WITH FEET 2 – END PANELS 2 – SIDES 1 – MATTRESS SUPPORT PLATFOR M

PA RTS INCLU DED IN HA RDWA RE B A G

18 – DECORATIVE BOLTS 1 – BALL END ALLEN WRENCH 18 – LOCK WASHERS