Room & Board Gallery Media Shelves Assembly Instruction
assembly instructions: gallery
List of parts
2 – side frames
5 – shelves
1 – wire management panel
Hardware
6 – sharp, self-drilling screws
20 – screws
14 – plastic bumpers
Tools needed
Phillips screwdriver
MADE IN Wisco nsin
Directions
1. Lay out the two side rails on a soft, flat surface. Note which side rail is right and which is
left. Attached steel shelf-mounting brackets should all face inward on both rails.
2. Star t with right side of rail and attach largest shelf (19" deep) to first steel bracket
mounted just above leg. Make sure cut-outs on shelf are facing toward the back. Inser t
screws into underside of shelf bracket and then up into pre-drilled holes on right side of
shelf. Tighten using a Phillips screwdriver (Figure 1).
3. Continue adding progressively smaller shelves to right side rail until all five are attached
with the smallest shelf on top (Figure 2).
4. Repeat steps 2 and 3 with left side rail (Figure 3).
5. Turn unit over so shelf cut-outs are facing up (Figure 4).
6. Attach the wire management panel ver tically into shelf cut-outs using sharp, self-drilling
screws (Figure 5). Make sure top of wire management panel is flush with third shelf from
bottom (A). Tighten screws with Phillips screwdriver.
7. Place a plastic bumper in each corner on back of every shelf. In addition, place two
bumpers at top back of each side rail pole for extra wall protection.
8. Tip unit upright next to wall moving unit around slightly so top of frame, or top shelf,
touches the wall first (Figure 6).
800.301.9720 | roomandboard.com
5/1/11
Manufactured in the USA by:
SIELAFF CORPORATION
Mineral Point, WI 53565
3
TOP END
TOP END
START WITH THE RIGHT SIDE FRAME AND THE LARGEST (19" DEEP)
SHELF STANDING ON THE FLOOR WITH THE BACK NOTCH DOWN.
5
CONTINUE ADDING PROGRESSIVELY SMALLER SHELVES UNTIL
ALL FIVE ARE ATTACHED.
19"
Manufactured in the USA by:
SIELAFF CORPORATION
Mineral Point, WI 53565
GALLERY Media Shelf
Room&Board
®
Assembly Instructions
3
6
4
2
ALL OF THE SHELVES
ATTACH LIKE THIS.
1
TO PROTECT THE STEEL AND WOOD PARTS, WORK ON A CARPETED FLOOR.
LAY OUT THE TWO SIDE FRAMES AS SHOWN. NOTE WHICH IS RIGHT & LEFT AND TOP & BOTTOM.
TOP END
LEFT FRAME
TOP END
START WITH THE RIGHT SIDE FRAME AND THE LARGEST (19" DEEP)
SHELF STANDING ON THE FLOOR WITH THE BACK NOTCH DOWN.
ATTACH THE NEXT SMALLER (18" DEEP) SHELF.
POSITION THE LEFT SIDE FRAME INTO THE SLOTS IN THE SHELF EDGES.
SCREW THE BRACKETS ONTO THE SHELVES.
BOTTOM
END
RIGHT FRAME
"STUBBY" PHILLIPS SCREWDRIVER
WORKS BEST.
18"
7
TURN THE UNIT OVER SO THE SHELF CUT-OUTS ARE FACING UP.
5
CONTINUE ADDING PROGRESSIVELY SMALLER SHELVES UNTIL
ALL FIVE ARE ATTACHED.
17"
8"
7"
19"
Manufactured in the USA by:
SIELAFF CORPORATION
Mineral Point, WI 53565
3
TOP END
TOP END
START WITH THE RIGHT SIDE FRAME AND THE LARGEST (19" DEEP)
SHELF STANDING ON THE FLOOR WITH THE BACK NOTCH DOWN.
RIGHT FRAME
7
TURN THE UNIT OVER SO THE SHELF CUT-OUTS ARE FACING UP.
5
CONTINUE ADDING PROGRESSIVELY SMALLER SHELVES UNTIL
ALL FIVE ARE ATTACHED.
17"
8"
7"
19"
Manufactured in the USA by:
SIELAFF CORPORATION
Mineral Point, WI 53565
3
TOP END
START WITH THE RIGHT SIDE FRAME AND THE LARGEST (19" DEEP)
SHELF STANDING ON THE FLOOR WITH THE BACK NOTCH DOWN.
Manufactured in the USA by:
SIELAFF CORPORATION
Mineral Point, WI 53565
GALLERY Media Shelf
Room&Board
®
Assembly Instructions
3
6
4
2
8
ALL OF THE SHELVES
ATTACH LIKE THIS.
1
TO PROTECT THE STEEL AND WOOD PARTS, WORK ON A CARPETED FLOOR.
LAY OUT THE TWO SIDE FRAMES AS SHOWN. NOTE WHICH IS RIGHT & LEFT AND TOP & BOTTOM.
TOP END
LEFT FRAME
TOP END
START WITH THE RIGHT SIDE FRAME AND THE LARGEST (19" DEEP)
SHELF STANDING ON THE FLOOR WITH THE BACK NOTCH DOWN.
ATTACH THE NEXT SMALLER (18" DEEP) SHELF.
POSITION THE LEFT SIDE FRAME INTO THE SLOTS IN THE SHELF EDGES.
SCREW THE BRACKETS ONTO THE SHELVES.
TIP THE UNIT UPRIGHT NEXT TO THE WALL
(THIS IS A TWO-PERSON JOB!)
MOST WALLS ARE NOT PERFECTLY STRAIGHT.
ALL BUMPERS DO NOT NEED TO BE TOUCHING
THE WALL. FOR BEST STABILITY, MOVE THE
UNIT SO THE TOP OF THE FRAME OR THE
TOP SHELF TOUCHES THE WALL FIRST.
BOTTOM
END
RIGHT FRAME
"STUBBY" PHILLIPS SCREWDRIVER
WORKS BEST.
18"
USE THE SHARP "SELF-DRILLING" WOOD SCREWS TO ATTACH THE WIRE MANAGER
INTO THE SHELF CUT-OUTS. MAKE THE TOP OF THE MANAGER FLUSH AT (A).
7
TURN THE UNIT OVER SO THE SHELF CUT-OUTS ARE FACING UP.
9
5
CONTINUE ADDING PROGRESSIVELY SMALLER SHELVES UNTIL
ALL FIVE ARE ATTACHED.
17"
8"
7"
19"
TOP END
START WITH THE RIGHT SIDE FRAME AND THE LARGEST (19" DEEP)
SHELF STANDING ON THE FLOOR WITH THE BACK NOTCH DOWN.
TIP THE UNIT UPRIGHT NEXT TO THE WALL
(THIS IS A TWO-PERSON JOB!)
7
TURN THE UNIT OVER SO THE SHELF CUT-OUTS ARE FACING UP.
9
CONTINUE ADDING PROGRESSIVELY SMALLER SHELVES UNTIL
ALL FIVE ARE ATTACHED.
17"
8"
7"
19"
assembly instructions: gallery
Step 1
19"
Step 3
TOP END
Step 2
Step 4
7"
8"
17"
Step 5
STICK PLASTIC BUMPERS AT
THE CORNERS OFTHE SHELVES.
(A)
PUT TWO BUMPERS AT THE TOP
OF THE POLES FOR EXTRA
WALL PROTECTION.
MOST WALLS ARE NOT PERFECTLY STRAIGHT.
ALL BUMPERS DO NOT NEED TO BE TOUCHING
THE WALL. FOR BEST STABILITY, MOVE THE
UNIT SO THE TOP OF THE FRAME OR THE
TOP SHELF TOUCHES THE WALL FIRST.
Step 6
800.301.9720 | roomandboard.com
4/1/11
Loading...