Rongta Technology RP80 WUS User Manual

80 Series Printer

User

Manual

Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20cm

between the radiator & your body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

1

Catalogue

I. Product Introduction .........................................................................................................3

1.1 Warnings: ......................................................................................................................3

1.2 Notice ............................................................................................................................3

II. Summary ..........................................................................................................................4

Main Features ......................................................................................................................4

III. Specification ....................................................................................................................4

IV. Installation And Operation .............................................................................................6

4.1 Contents in the package .................................................................................................6

4.2 Printer Connection .........................................................................................................7

4.3 Load the Paper Roll .......................................................................................................8

V. Power Switch, Keystroke and Indicator Light ................................................................9

5.1 Power Switch.................................................................................................................9

5.2 Keystroke and Indicator Light .......................................................................................9

5.3 Setting Printer Mode .................................................................................................... 10

5.4 Self-checking ............................................................................................................... 10

VI. Cash Drawer Interface.................................................................................................. 11

VII. Printer Maintenance.................................................................................................... 11

7.1 Print Head Maintenance............................................................................................... 11

7.2 Sensor Maintenance ..................................................................................................... 12

7.3 Print Roll Maintenance ................................................................................................ 12

VIII. Fix the Paper Jam ...................................................................................................... 13

IX. Fault treatment ............................................................................................................. 13

9.1 When indicators light on the control board is out ......................................................... 13

9.2 The indicator light is on, while the printer can’t work .................................................. 13

X. Printer driver .................................................................................................................. 14

2

I. Product Introduction

80 series printer is a POS direct thermal receipt printer with easy operation and
high cost effective, which is widely used in supermarket, hospital, restaurant, bank,
oil station, turnpike etc.

Safety Notice

Please read carefully and strict compliance with use of following instructions

before operating the printer.

1.1 Warnings:

Warning: Do not touch the cutter of printer.

Warning: The print head is heating component; do not touch it and its peripheral

parts during the printing process or the print just ended.

Warning: Do not touch the surface of the print head and its connecting parts to

avoid damage it.

1.2 Notice

(1) The printer should be installed at a firm place and avoid it in vibration and shake.
(2) Do not use or store the printer in the location of high

temperature, humidity or heavy pollution.

(3) The power adapter of printer should be connected to a properly grounded

receptacle. Avoid using the same socket with other large electronic machines or

the equipment which could cause the voltage fluctuation.
(4) Do not let water or conductive material like metal get inside the printer, if it

happens, please turn off the power supply immediately.
(5) Printer could not be worked when there is no paper; otherwise it would seriously

damage the print roll and the thermal print head.
(6) Please disconnect the power supply if do not use the printer for a long time.
(7) The user should not dismantle the printer by self for repairing or remolding.
(8) Use only the standard power adapter supplied together with the printer.

3

(9) In order to ensure the printing quality and extend the life of printer, please use the

recommendatory thermal paper or the one which has the same quality.
(10) Please make sure the power of printer is off when plugging the connecting line.
(11) Please keep the user manual for reference when needed.

II. Summary

Main Features

● High print quality

● Low noise

● Supports cash drawer driver

● Exquisite and lightweight，Pretty outside design

● Reasonable structure, easy using

● The font could be magnified, bolded or underlined, and also the character line

spacing and left and right spacing can be adjusted before printing.

● Supports the print of different density bitmap and download figure.

● To realize and call built-in and cartridge font high speed printing in driver

printing(dot printing).

● Low power consumption and operation cost（No need ribbon or ink box）

● Emulation: ESC/POS

III. Specification

● Printing Method：Direct thermal printing

● Paper Width：79.5±0.5mm

● Effective Printing Width：72mm

● Printing Speed：250mm/s

● Print head performance

Resolution：504 dots/line or 576 dots/line
TPH: 100KM

● Interface：

4