USEANDMAINTENANCEMANUAL_GB
“SANDY 2”
ref.94451-94476-94880
The descriptions contained in this document are not binding.
The company therefore reserves the right to make any modifications at any time to parts,
details or accessory supply, as considered necessary for reasons of improvement or for
manufacturing/commercial requirements.
The reproduction, even partial, of the text and drawings c ontain ed in t his doc um ent is proh ibited
by law.
The company reserves the right to make any technical and/ or s upply mod ificati ons. Th e images
are shown as a reference only, and are not binding as to the actual design and/or equipment.
SYMBOLS USED IN THE MANUAL
Open book symbol with an "i"
Indicates the need to consult the instruction manual
Open book symbol:
Used to tell the operator to read the manual before using the machine
Warning symbol
Carefully read the sections marked with this sy mbol and observe the
indications, for the safety of the operator and the machine
Warning symbol
Indicates the risk of gas exhalation and leakage of corrosive liquids
Warning symbol
Indicates that the packed product should be hand led with suitabl e lifting
means that comply with the legal requirements
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
3
CONTENTS
ON CONSIGNMENT OF THE MACHINE............................................................................................................................................................ 4
INTRODUCTORY COMMENT ............................................................................................................................................................................ 4
INTENDED USE .................................................................................................................................................................................................. 4
SERIAL NUMBER PLATE .................................................................................................................................................................................. 4
TECHNICAL DESCRIPTION............................................................................................................................................................................... 4
SYMBOLS USED ON THE MACHINE ................................................................................................................................................................ 5
GENERAL SAFETY REGULATIONS ................................................................................................................................................................. 6
MACHINE PREPARATION ................................................................................................................................................................................. 7
1. HANDLING THE PACKED MACHINE ................................................................................................................................................................................. 7
2. HOW TO UNPACK THE MACHINE ..................................................................................................................................................................................... 7
3. HOW TO MOVE THE MACHINE ......................................................................................................................................................................................... 7
4. HANDLING AND TRANSPORTATION OF THE MACHINE ................................................................................................................................................ 7
5. HANDLEBAR COMPONENTS ............................................................................................................................................................................................. 7
6. STEERING COLUMN COMPONENTS ................................................................................................................................................................................ 8
7. ADJUSTING THE HANDLEBAR – WORK POSITION ........................................................................................................................................................ 8
8. ASSEMBLING THE SOLUTION TANK (OPTIONAL) .......................................................................................................................................................... 8
9. DETERGENT SOLUTION .................................................................................................................................................................................................... 9
10. ASSEMBLING THE BRUSH .............................................................................................................................................................................................. 9
WORK ............................................................................................................................................................................................................... 10
11. PREPARING TO WORK .................................................................................................................................................................................................. 10
12. MANOEUVRABILITY OF THE MACHINE ....................................................................................................................................................................... 10
13. WORK............................................................................................................................................................................................................................... 10
AT THE END OF THE WORK ........................................................................................................................................................................... 12
DAILY MAINTENANCE .................................................................................................................................................................................... 13
14. DISASSEMBLING THE BRUSH / PAD-HOLDER ............................................................................................................................................................ 13
WEEKLY MAINTENANCE ................................................................................................................................................................................ 14
15. CLEANING THE SOLUTION TANK ................................................................................................................................................................................. 14
TROUBLESHOOTING ...................................................................................................................................................................................... 15
16. THERMAL CUT-OUT ....................................................................................................................................................................................................... 15
17. NOT ENOUGH DETERGENT SOLUTION ON THE BRUSH (OPTIONAL) .................................................................................................................... 15
18. THE MACHINE VIBRATES OR OSCILLATES ................................................................................................................................................................ 15
DISPOSAL ........................................................................................................................................................................................................ 16
CHOOSING AND USING THE BRUSHES ....................................................................................................................................................... 17
ELECTRICAL SYSTEM DIAGRAM - 94451 ..................................................................................................................................................... 18
ELECTRICAL SYSTEM DIAGRAM – 94476- 1800W ....................................................................................................................................... 19
ELECTRICAL SYSTEM DIAGRAM – 94480- 2200W ....................................................................................................................................... 20
EC DECLARATION OF CONFORMITY ............................................................................................................................................................ 21
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
4
ON CONSIGNMENT OF THE MACHINE
When the machine is consigned to the cus tomer, an immediate check
must be performed to ensure all the material mentio ned in the shipping
documents has been received, and also to check the machine has not
suffered damage during transportation. If this is the case, the carrier
must ascertain the extent of the damage at once, informing our
customer service office. It is only by prompt action of this ty pe that the
missing material can be obtained, and compensation for damage
successfully claimed.
INTRODUCTORY COMMENT
CM33-43 F and CM33-43 F PLUS These machines are built for the
professional cleaning of hard and vinyl indoor floors, to be carried out by
following the instructions. Any use of the mach ine for other purposes is
dangerous and therefore prohibited. The machine is suitable for
collective use, for example in hotels, schools, hospit als, factor ies , shops ,
offices and condominiums.
The machine must be used only for this purpose.
Even the best machines will only work well if used correctly an d kept in
good working order. This brochure offers you all the information
necessary to use the models of the "single-disc" machines in a regular,
safe and suitable manner, and it must alway s be kept available for the
user. We therefore recommend you read this instruction booklet
carefully, and consult it whenever difficulties arise while using the
machine. If necessary, remember that our customer assis tance service
(organised in collaboration with our dealers) is always available for
advice or direct intervention.
INTENDED USE
The floor scrubbing machine is designed for t he profe ssional cleani ng of
surfaces and floors in industrial, commercial and public environments
only. It is only suitable for use in closed (or at least covered) places.
The machine is not suitable for use in the rain, or under water jets. It is
FORBIDDEN to use the machine for picking up dangerous dusts or
inflammable liquids in places with an explosive atm osphere. In addition,
it is not suitable as a means of transport for people or objects.
SERIAL NUMBER PLATE
TECHNICAL DESCRIPTION UM 94451
94476
(1800W) 94480 (2200W)
Working width mm 430 430 430
Disc brushes
mm
430 430 430
Brush rotations rpm 160 160 160
Brush motor power W 1350 1800 2200
Brush motor voltage V 230 230 230
Brush motor frequency Hz 50 50 50
Maximum gradient with full load % 2 2 2
Solution tank capacity (optional) l 15 15 15
Rear wheel diameter mm 175 175 175
Machine length mm 600 600 600
Machine height at motor level (without brush) mm 290 325 350
Machine height at steering gear level (without brush) mm 1155 1155 1155
Machine width Tank mm 450 450 450
Machine service weight (without solution tank) kg 40 42 45
Length of power supply cable m 15 15 15
Sound pressure level (ISO 11201) - L pA dB (A) <70 <70 <70
Uncertainty KpA dB (A) 1.5 1.5 1.5
Hand vibration level (ISO 5349) m/s2
<2.5 <2.5 <2.5
Uncertainty of measurement of vibrations
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
5
SYMBOLS USED ON THE MACHINE
Indicates the earth connection point of the electric system of the machine
Voltage symbol
Warning - high voltage 230 Volt.
Indicates the maximum gradient.
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
6
GENERAL SAFETY REGULATIONS
The regulations below must be carefully followed in order to avoid harm to the operator and damage to the machine.
WARNING:
Read the labels on the machine carefully. Do not cover them for any reason, and replace them immediately if they become damaged.
The machine must be exclusively used by authorised, trained personnel.
Do not use the machine on surfaces with an inclination greater than the one shown on the plate.
The machine is not suitable for cleaning rough or uneven floors. Do not use the machine on slopes.
If the power supply cable gets damaged, the mach ine mus t be st opp ed if it is op erating . Disc onnect t he plug fr om the p ower sup ply , and h ave the c able
replaced immediately by an authorised service centre.
In the event of danger, quickly disconnect the power cable plug from the mains socket.
For all maintenance interventions, switch off the machine and disconnect the power cable plug from the mains socket.
Children must be supervised to ensure they do not play with the machine.
During the working of the machine, pay attention to other people and especially to children.
Use only the brushes or pad holders supplied with the machine, or those specifie d in the Instructions Manual - in the para graph "CHOOSING AND
USING THE BRUSHES". The use of other brushes or pad holders could compromise safety levels.
The machine must only be powered with a voltage of the level shown on the serial number plate.
ATTENTION:
The machine is not suitable for use by children and persons with reduced phy sical, ment al and sens ory capa bilities, or pe ople w ho lack experience and
knowledge.
The machine must not be used or stored outdoors, in damp conditions or directly exposed to rain.
The storage temperature must be between -25C and +55C; do not store outdoors in damp conditions.
Conditions of use: room temperature between 0°C and 40°C, with relative humidity between 30 and 95%.
The socket for the machine power cable must have a prescribed earth connection.
Adapt the speed to the adhesion conditions.
Do not use the machine as a means of transport.
The machine does not cause harmful vibrations.
Do not use the machine in an explosive atmosphere.
Do not use the machine to collect dangerous powders.
Do not mix different types of detergent as this may produce harmful gases.
The machine is not suitable for cleaning carpets or textile flooring.
Do not place any liquid containers on the machine.
Avoid working with the brushes when the machine is standing still, so as to avoid damage to the floor.
Avoid damaging the machine power cable by crushing or bending it, or by applying stress.
Attention: do not let the power cable come into contact with the rotating brush.
In the event of a fire, use a powder extinguisher. Do not use water.
Do not knock against shelving or scaffoldi ng, where there is a danger of fall ing objects. The operator must always b e equipped with the appropriate
safety devices (gloves, shoes, helmet, goggles, etc.).
Polishing operations must only be carried out in areas where the passage of unauthorised persons is prohibi ted. Signal the presence of d amp floors
with suitable signs.
If the machine does not work properly, chec k this is not caused by failure to carry out routine mainten ance. Otherwise, ask for intervention of the
authorised technical assistance centre.
If you need to replace any components, request the ORIGINAL spare parts from an Authorised dealer and/or Retailer.
Restore all electrical connections after any maintenance interventions.
Before using the machine, check that all the hatches and covers are positioned as shown in this Use and Maintenance Manual.
Do not remove the guards that can only be removed with the aid of tools, except for maintenance work (see the relevant paragraphs).
Do not put your hands into the machine during operation.
Do not remove the covers and/or guards when the machine is running.
Do not operate the machine without any protections.
Do not approach the machine with clothes that could get entangled: AVOID the use of scarves, shawls, wraps and loose clothing.
Avoid working over pieces of rope, wire, cables: these can be caught in the brush and create friction.
Do not wash the machine with direct water jets or with pressurised water, nor with corrosive substances.
Do not use acid or basic solutions that could damage the machine and/or harm people.
Have the machine checked by an authorised technical assistance centre every year.
When disposing of consumable materials, observe the laws and regulations in force.
When your machine has reached the end of its long working life, d ispose of the material s it contains (espe cially oils and elec tronic components) in an
appropriate manner, taking into account that the machine itself was constructed by using 100% recyclable materials.
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
7
MACHINE PREPARATION
1. HANDLING THE PACKED MACHINE
The machine is contained in specific packaging with a pallet for the handling with fork trucks. The
packages CANNOT be placed on top of each other.
The total mass of the machine with packaging is 44kg (94451 without solution tank).
The total mass of the machine with packaging is 46kg (94476-1800W without solution tank).
The total mass of the machine with packaging is 49kg (94480- 2200W without solution tank).
The dimensions of the packaging are as follows:
A : 1190 mm
B : 610 mm
C : 490 mm
A
C
B
2. HOW TO UNPACK THE MACHINE
1. The machine is fixed inside the box by means of reinf orcements; remove them a nd set the m aside for
any future transportation.
2. Remove the outer package.
3. Use a chute to get the machine down from the pallet, pulling it backwards.
4. Keep the pallet for any future transport needs.
ATTENTION: If the product is delivered in cardboard containers, handle the
packed product with suitable lifting means that comply with the legal requirements
3. HOW TO MOVE THE MACHINE
1. Make sure the solution tank (optional) is empty.
2. Remove the brush from the base (see “DISASSEMBLING THE BRUSH / PAD-HOLDER).
3. Position the single brush on the pallet by means of a chute.
4. Insert the cardboard and the previously kept supports.
4. HANDLING AND TRANSPORTATION OF THE MACHINE
To handle the machine safely, proceed as follows:
1. Make sure the solution tank (optional) is empty.
2. Rotate the handlebar to its resting position (see ADJUSTING THE HANDLEBAR – WORK
POSITION) and lock it in place.
3. Tilt the machine, by putting a foot into the rear of the base body, s o only the rear wheels touch the
ground and the machine can move freely.
5. HANDLEBAR COMPONENTS
The handlebar components are identified as follows:
1. Main switch control lever.
2. Handlebar tilt adjustment lever.
3. Solution tank tap control lever (optional).
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
8
MACHINE PREPARATION
4. Dead man's lever.
6. STEERING COLUMN COMPONENTS
The handlebar column components are identified as follows:
1. Cable winder bracket.
7. ADJUSTING THE HANDLEBAR – WORK POSITION
Before you start working with the machine, you will need to find the c orrec t work pos ition . To do this , pres s
the tilt adjustment lever, release it until your arms are slightly bent and as low as possible, while keepi ng
the back straight and the legs slightly apart.
When working the operator is behind the machine.
8. ASSEMBLING THE SOLUTION TANK (OPTIONAL)
To insert the solution tank onto the handlebars, proceed as follows:
1. Secure the handlebar in a position at about 45° in relation to the ground.
2. Loosen the closing knob (1) and position the top brackets more than halfway up the column (if they
are not already in place).
3. Put the solution tank on the column, s o that th e bottom of the tank is anc hored t o the f ixed brack et (2)
on the column itself.
4. Holding the tank with one hand, move the mobile bracket (3) down until the solution tank i s locked to
the column.
5. Lock the position of the mobile bracket (3) by tightening the closing knob (1).
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
9
MACHINE PREPARATION
6. Insert the water distribution pipe (4) in the hole on the brush head (5).
9. DETERGENT SOLUTION
Fill the solution tank only when the column is in vertical position, by proceeding as follows:
1. Fill it with clean water at a temperature not exceeding 50C.
2. Add the liquid detergent to the tank in the concentration and manner indicated on the detergent
manufacturer's label. The formation of exces s foam could damage the internal components of the
machine, so only use the minimum amount of detergent needed.
WARNING: you are advised to always wear protective gloves, to avoid the risk of
serious injury to your hands
WARNING: We recommend that you vacuum at intervals the dirt-loaded f oam with a
vacuum cleaner for liquids.
10. ASSEMBLING THE BRUSH
To insert the brush:
1. Plug the power supply cable into the mains socket.
2. Place the brush in front of the brush head unit.
3. Raise the brush head by using the handlebar as a lever.
4. Position the brush head above the brush.
5. Activate the handlebar tilt lever.
6. Press the dead man's lever and pulse-press the m ain switch control lever to insert the brush in the
brush head.
WARNING: you are advised to always wear protective gloves, to avoid the risk of
serious injury to your hands
WARNING: during this operation, check there are no people or ob jects near the
brush.
WARNING: Make sure the brushes are correctly connected. If this is not the case,
the machine could move in an irregular, sudden manner.
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
10
WORK
11. PREPARING TO WORK
1. Make sure the power supply cable is not damaged.
2. Plug the power supply cable of the machine into the mains socket.
3. Bring the handlebar to the work position by acting on the release lever.
12. MANOEUVRABILITY OF THE MACHINE
The first time an operator uses the machine, he/s he should become familiar with the movements to be
imparted to the shaft in order to be confident enough with the directio nality of movement of the machine ,
and should therefore not operate the machine near people or obstacles.
Work in slow movements to the right and left, possibly moving bac k so that the operat or always stands on
an area of the floor yet to be cleaned up.
Keep the power supply cable behind th e operator, taking care not to op erate the machine in its vicinity in
order not to damage it.
Do not insist too much on the same ar ea so as t o avoid da maging the floor, also i n function of the type of
brush or abrasive floor pad chosen.
In operation, the machine moves to the right by slightly lifting the handlebars.
In operation, the machine moves to the left by slightly lowering the handlebars.
13. WORK
1. At this point, by pressing the dead man's lever (1) and activ ating the mai n switch c ontrol lever (2), the
machine can operate at full efficiency.
2. Let the machine run on dry for a few seconds (optional solution tank kit).
3. Apply a small amount of detergent solution to the floor by pressing the lever (3) until the brush is
saturated with foam (optional solution tank kit).
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
11
WORK
4. Push the machine with the brush rotating from left to right or vice versa.
5. Immediately afterwards, push the mac hine in the same way but in the opposite direction, so that
about one quarter of the working width overlaps the previous one.
6. We recommend that you vacuum up the d irt-l oad ed f oa m at i nterv a ls with the aid of a vacuum cleaner
for liquids (optional solution tank kit).
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
12
AT THE END OF THE WORK
A
t the end of the work, and before carrying out any type of maintenance, perform the following
operations:
1. Disconnect the plug from the mains socket.
2. Wind it onto the rear brackets.
3. Operate the handlebar adjustment lever (1) and bring the column to its idle position.
4. Move the machine indoors, in an area where it cannot cause any damage to people or
surrounding property, but where it can also be protected against th e accidental fall of objects. In
addition, do not park the machine in open places or on sloping floors
5. Disassemble the brush and clean it with a jet of water (to disassemble the brush, see
“DISASSEMBLING THE BRUSH / PAD-HOLDER” below).
ATTENTION: you are advised to always wear protective gloves, to avoi d the
risk of serious injury to your hands.
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
13
DAILY MAINTENANCE
PERFORM ALL MAINTENANCE OPERATIONS IN SEQUENCE
14. DISASSEMBLING THE BRUSH / PAD-HOLDER
1. Make sure the power supply cable is unplugged from the mains socket.
2. Check that the handlebar is in its idle position.
3. Tilt the machine until the handlebar is on the ground (do this by placing your fo ot on the rear of the
brush head unit).
WARNING: This operation must be carried out using gloves to protect agai nst
contact with dangerous solutions.
4. Rotate the brush anticlockwis e un til it is released from the brush-holder plate, th en c lean it with a jet
of water. Check the bristles. If they are excessively worn, replace th e brushes (the bristles should
protrude by at least 10mm).
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
14
WEEKLY MAINTENANCE
15. CLEANING THE SOLUTION TANK
Proceed as follows to clean the solution tank:
1. Make sure the solution tank is empty; otherwise, empty it by keeping the tap control lever operating.
2. Secure the handlebar in a position at about 45° in relation to the ground.
3. Remove the water distribution pipe (4) from the hole on the brush head (5).
4. Loosen the closing knob (1) and position the top brackets more than halfway up the column.
5. Remove the solution tank and clean it with a jet of running water.
6. To position it on the machine, refer to “ASSEMBLING THE SOLUTION TANK (OPTIONAL)”.
ATTENTION: you are advised to always wear protective gloves, to avoi d the
risk of serious injury to your hands.
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
15
TROUBLESHOOTING
16. THERMAL CUT-OUT
The single-disc machine is equipped with the following electrical protection systems, thermal cut-out
(1), located off the handlebars, to protect the motor. In the ev ent of malfunctioning, check a thermal
cut-out has not intervened. If the motor overheats, its t hermal cut-out interv enes to block the elec tricity
supply. Wait a few minutes until it has cooled down, then press the s pecific circuit breaker button to
reactivate the power supply and motor operation.
17. NOT ENOUGH DETERGENT SOLUTION ON THE BRUSH (OPTIONAL)
1. Check that the valve allowing the detergent solution to flow from the tank to the brush is not
blocked. Flush the tank if needed.
2. Check that the solution distribution pipe is not blocked. Flush it out if necessary.
18. THE MACHINE VIBRATES OR OSCILLATES
The machine has been sitting in res t position for too long, with the brush or pad holder still inserted.
Replace as soon as possible.
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
16
DISPOSAL
To dispose of the machine, take it to a demolition centre or an authorised collection centre.
Before scrapping the machine, it is necess ary to remove and separ ate out the following mat erials, then
send them to the appropriate collection centres in accordance with the environmental hygiene
regulations currently in force:
Brushes
Felt
Electric and electronic parts*
Plastic parts (tanks and handlebar)
Metal parts (levers and frame)
(*) In particular, contact your local distributor when scrapping electric and electronic parts.
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
17
CHOOSING AND USING THE BRUSHES
POLYPROPYLENE BRUSH (PPL)
Used on all types of floor, it has good resis tance to wear and tear and hot water (not more than 60°C). PPL is non-hygroscopic and therefore retains its
characteristics even when working in wet conditions.
NYLON BRUSH
Used on all types of floors. Excellent resistance to wear and t ear, and hot water (even over 60°C). The nylon is hygroscopic and so tends to lose its
characteristics over time when working in wet conditions.
ABRASIVE BRUSH
The bristles of this type of brush are charged with highly aggress ive abras ives . It is used to clean v ery dirty floors . To avoi d floor dama ge, work onl y with the
pressure strictly necessary.
THICKNESS OF THE BRISTLES
Thicker bristles are more rigid and are therefore used on smooth floors or floors with small joints.
On uneven floors or those with deep joints, it is advisable to use softer bristles which can enter the gaps more easily.
Remember that when the bristles are worn and theref ore too s hort, th ey will b ecom e rigid and are no lon ger abl e to pe netr ate and c lean deep down; as with
over-large bristles, the brush tends to jump.
PAD HOLDER
The pad holder is recommended for cleaning shiny surfaces.
There are two types of pad holder:
1. The traditional pad-holder has a series of anchor points that hold and drag the abrasive disc while working.
2. The CENTRE LOCK type pad-holder not only has anchor points, but also a snap-type central locking system in plastic that allows the abrasive disc to
be perfectly centred and held without any risk of it be coming detached. This type of h older is especially suit able for machines with several br ushes,
where it is difficult to centre the abrasive di scs.
TABLE FOR CHOOSING THE BRUSHES
Machine
No. of brushes
Code Type of bristles
Bristles Brush
Length Notes
94451
94476-
94480
1
431361
431360
405657
431362
PPL
PPL
ABRASIVE
-
0.7
0.45
-
-
420
420
420
430
BRUSH
BRUSH
BRUSH
PAD HOLDER
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
18
ELECTRICAL SYSTEM DIAGRAM - 94451
POS COMPONENT NAMES
POS CABLE NAMES
ABBR CABLE
1 Cut-out 8A
1 Cable 3x1.5x15 metres + Schuko plug -1-
BK Black
2 Operating switch 16A
2 Cable 3x1.5x1680 -2-
BU Blue
4 Noise filter
3 Brown cable 1.5x150 -3-
BN Brown
5 Operating condenser 30F
RD Red
6 Start condenser 145-174F
WH White
7 Klixon
GY Grey
8 230V motor
GNYE Yellow-green
9 Plug 16A
GN Green
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
19
ELECTRICAL SYSTEM DIAGRAM – 94476- 1800W
POS COMPONENT NAMES
POS CABLE NAMES
ABBR CABLE
1 Cut-out 8A
1 Cable 3x1.5x15 metres + Schuko plug -1-
BK Black
2 Operating switch 16A
2 Cable 3x1.5x1680 -2-
BU Blue
4 Noise filter
3 Brown cable 1.5x150 -3-
BN Brown
5 Operating condenser 50F
4 2 white cables 1.5x250 -4-
RD Red
6 Start condenser 120F
5 2 black cables 1.5x250 -5-
WH White
7 Klixon
GY Grey
8 230V motor
GNYE Yellow-green
9 Plug 16A
GN Green
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
20
ELECTRICAL SYSTEM DIAGRAM – 94480- 2200W
POS COMPONENT NAMES
POS CABLE NAMES
ABBR CABLE
1 Cut-out 10A
1 Cable 3x1.5x15 metres + Schuko plug -1-
BK Black
2 Operating switch 16A
2 Cable 3x1.5x1680 -2-
BU Blue
4 Noise filter
3 Brown cable 1.5x150 -3-
BN Brown
5 Operating condenser 60F
4 2 white cables 1.5x250 -4-
RD Red
6 Start condenser 120F
5 2 black cables 1.5x250 -5-
WH White
7 Klixon
GY Grey
8 230V motor
GNYE Yellow-green
9 Plug 16A
GN Green
ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE
21
EC DECLARATION OF CONFORMITY
The undersigned company:
ROMUS
Z.A. Les Pouards - 13 et 15 rue Taillefer
91160 CHAMPLAN – FRANCE
declares under its sole responsibility that the products
SINGLE-DISC MACHINES 94451 – 94476 1800W -94480 - 2200W
comply with the requirements of the following Directives:
2006/42/EC: Machinery Directive
2006/95/EC: Low Voltage Directive
2004/108/EC: Electromagnetic Compatibility Directive
They also comply with the following standards:
EN 60335-1: Household and similar electrical appliances - Safety. Part 1: Generic norms
EN 60335-2-67: Household and similar elec trical appliances. Part 2: Specific norms for automatic machines for floor treatment for commercial and
industrial use
EN 12100-1: Machine safety - Fundamental concepts, fundamental principles of design - Part 1: Basic terminology and methodology
EN 12100-2: Machine safety - Fundamental concepts, fundamental principles of design - Part 2: Technical principles
EN 55014-1: Electromagnetic compatibility - Regulations for household appliances, electrical devices and similar equipment. Part 1: Emission -
Regulations for product family.
EN 55014-2: Electromagnetic compatibility - Regulations for household appliances, electrical devices and similar equipment. Part 2: Immunity -
Regulations for product family.
EN 61000-3-2: Electromagnetic compatibility (EMC) - Part 3-2: Limits – Limits for harmonic current emissions (Equipment with input current 16 A per phase).
EN 61000-3-3: Electromagnetic compatibility (EMC) - Part 3-3: Limits – Restriction of v oltage v ariations and flic ker in low vol tage power supply systems
for devices with a rated current 16 A.
EN 62233: Household and similar electrical appliances - Electromagnetic fields Methods for evaluation and measurement
The person authorised to compile the technical file:
M. Régis de boissieu
Z.A. Les Pouards
13 et 15 rue Taillefer
91160 CHAMPLAN – FRANCE
Champlan, 02/11/2013
ROMUS
Legal representative
Loading...