www.rominafurniture.com
ASSEMBLY INSTRUCTIONS
FOR ANTONIO & CLEOPATRA FULL SIZE BEDS
AND CONVERTIBLE CRIBS FULL SIZE BED OPTION
(PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 6501 & 7501 CONVERTIBLE CRIBS”)
IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR FUTURE USE.
THE STYLE OF YOUR BED / RAILS / ACCESSORIES MAY VARY
FROM WHAT IS PICTURED IN THE INSTRUCTION SHEET
6530 6532 6537
7530 7532 7537
3
7
1
2
Antonio & Cleopatra full beds box content:
HB headboard or tufted headboard = 1
LPFB low profile footboard = 1
BR bed rails = 1 + 1
SL group of support slats
assembled with textile ribbons = 2
WO wooden ornament = 2 + 2
HK full bed hardware kit = 1
Antonio & Cleopatra conversion kit box content:
BR bed rails = 1 + 1
SL group of support slats
assembled with textile ribbons = 2
WO wooden ornament = 2 + 2
HK full bed hardware kit = 1
wooden cap = 4
Antonio & Cleopatra full bed hardware kit:
1. Allen key = 1
2. screw-in dowel (cam stud) = 4
3. eccentric connecting fitting (cam lock) = 4
4. Allen bolt (40 mm - 1 5/8” ) = 8 w/o centering tip
5. wood screw (35 mm - 1 3/8") = 8
6. Allen bolt (100 mm - 4") = 6
7. barrel nut = 6
5
4
Phillips screwdriver (not supplied)
6
Notes:
The letters which identifies a part are the
initials of the respective part name (such
method is employed to facilitate parts
recognition between the drawings and the
parts list).
The item number of your product is located
on a black and white label. Please, refer to
this number in the event that you need to call
ROMINA FURNITURE or your local
distributor. Thank you.
WARNING!
Be sure to COMPLETELY TIGHTEN the
screws / bolts when you are asked to do so.
Required tools:
Allen wrench (supplied), Phillips screwdriver
(not supplied).
CAUTION:
Do not use a power screwdriver which can
cause screws to break or strip
SL
WO
BR
Assembly instructions for Antonio & Cleopatra full size beds
STEP 1 (Two adults are required to complete this step)
Attach the bed rails (BR) to the headboard (HB) using all six bigger Allen bolts (6) and all six barrel nuts (7). Make sure that the wood brackets attached to the bed rails faces towards
the inside of the bed. Align the straight slots in the heads of the barrel nuts horizontally. You can adjust the position of the barrel nut with a flat head screwdriver (not supplied) or a
coin. Push the Allen bolts through the headboard and into the bed rail. Start the thread by hand to assure you don't strip the threads then use the supplied Allen key (1). Do not
completely tighten the bolts at this step, you will be asked to do that later.
STEP 2 (Two adults are required to complete this step)
Insert the metallic hooks attached to the ends of the bed rails into the slots provided in the footboard's legs, so the hooks will catch the inner metallic pins. Make sure that both bed
rails are firmly attached to the footboard (LPFB).
Completely tighten all six bigger Allen bolts (6).
STEP 3
Using all eight smaller Allen bolts (4), all four cam studs (2) and all four cam locks (3) attach the wooden ornaments (WO) to the bed rails (BR) and to the end panels (HB) & (LPFB),
following the next steps:
A) using a Phillips screwdriver (not supplied) or just the hand insert a cam stud (2) in one crib’s foot (please see the assembly tip);
B) insert the cam lock (3) into the inner face hole of the wooden ornament, taking care that the little arrow of the cam is pointing to the wooden ornament’s vertical side;
C) attach the wooden ornament (WO) to the end panel (HB) or (LPFB), inserting the cam stud into the hole found on the wooden ornament’s vertical side;
D) insert two smaller Allen bolts (4) starting the thread by hand. Do not completely tighten the bolts at this moment, you will be asked to do this later. Adjust the position of the wooden
ornament to follow the lines of the crib’s foot by slightly moving the ornament then, using the supplied Allen key and moderate force, slightly rotate the cam lock clockwise (see the
cam’s rounded arrow) by about 90 deg to 120 deg until become tight. You don’t need to over-tight the cam! Again, using the supplied Allen key and moderate force, completely
tighten the smaller Allen bolts (4).
Repeat the above steps (A-D) for the rest of the three wooden ornaments.
STEP 4
Place the support slats (SL) onto the wood brackets attached to the bed rails. Position the support slats evenly between the bed ends. Make sure you firmly attach the support slats
to the wood brackets using all eight wood screws (5). Use a Phillips screwdriver (not supplied) to completely tighten the wood screws.
After completing STEP 4, your bed should look like one of the beds depicted on the first page of this instruction booklet.
Assembly instructions for Antonio & Cleopatra convertible cribs full size bed option
STEP 1 (Two adults are required to complete this step)
Completely disassemble your crib, taking care not to scratch the wood finish. (see STEPS 3 to 1 from “ASSEMBLY INSTRUCTIONS FOR YOUR 6501 & 7501 CONVERTIBLE
CRIBS”).
Keep the footboard and the headboard of your crib for the next step and carefully store the other resulted wooden pieces and hardware in a proper place, away from direct sunlight
and moisture, taking care not to scratch the wood finish.
STEP 2 (Two adults are required to complete this step)
Attach the bed rails (BR) to the headboard (HB) of the crib using all six bigger Allen bolts (6) and all six barrel nuts (7). Make sure that the wood brackets attached to the bed rails
faces towards the inside of the bed. Align the straight slots in the heads of the barrel nuts horizontally. You can adjust the position of the barrel nut with a flat head screwdriver (not
supplied) or a coin. Push the Allen bolts through the headboard and into the bed rail. Start the thread by hand to assure you don't strip the threads then use the supplied Allen key (1).
Do not completely tighten the bolts at this step, you will be asked to do that later.
STEP 3 (Two adults are required to complete this step)
Insert the metallic hooks attached to the ends of the bed rails into the slots provided in the footboard's legs, so the hooks will catch the inner metallic pins. Make sure that both bed
rails are firmly attached to the footboard (FB).
Completely tighten all six bigger Allen bolts.
STEP 4
Using all eight smaller Allen bolts (4), all four cam studs (2) and all four cam locks (3) attach the wooden ornaments (WO) to the bed rails (BR) and to the end panels (HB) & (FB),
following the next steps:
A) using a Phillips screwdriver (not supplied) or just the hand insert a cam stud (2) in one crib’s foot (please see the assembly tip);
B) insert the cam lock (3) into the inner face hole of the wooden ornament, taking care that the little arrow of the cam is pointing to the wooden ornament’s vertical side;
C) attach the wooden ornament (WO) to the end panel (HB) or (FB), inserting the cam stud into the hole found on the wooden ornament’s vertical side;
D) insert two smaller Allen bolts (4) starting the thread by hand. Do not completely tighten the bolts at this moment, you will be asked to do this later. Adjust the position of the wooden
ornament to follow the lines of the crib’s foot by slightly moving the ornament then, using the supplied Allen key and moderate force, slightly rotate the cam lock clockwise (see the
cam’s rounded arrow) by about 90 deg to 120 deg until become tight. You don’t need to over-tight the cam! Again, using the supplied Allen key and moderate force, completely
tighten the smaller Allen bolts (4).
Repeat the above steps (A-D) for the rest of the three wooden ornaments.
STEP 5
Place the support slats (SL) onto the wood brackets attached to the bed rails. Position the support slats evenly between the bed ends. Make sure you firmly attach the support slats
to the wood brackets using all eight wood screws (5). Use a Phillips screwdriver (not supplied) to completely tighten the wood screws.
HB
BR
WO
7
7
7
2
4
4
3
REQUIRED
WARNING:
TO KE EP YOUR BAB Y
SECURE AND SAFE, AND TO
AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO
COMPLETELY TIGHTEN ALL BOLTS AND
SCREWS USED TO ASSEMBLE THE BED.
FB
HB
SL
SL
BR
WO
WO
FB
BR
5
5
5
5
5
5
5
4
7
3
3
7
6
2
2
2
4
4
4
3
4
3
BR
5
WO
LPFB
WARNING!
COMPLETELY TIGHTEN!
0
+
-
assembly tip
little
arrow
r
o
u
n
d
e
d
a
r
r
o
w
GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina Furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.
Page intentionally left blank.
Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of the
fine finish of your Romina Furniture product.
Visit
www.rominafurniture.com
for updates, special offers and more new designs.
Team
Thank you for being one of our distinguished clients.
Loading...