IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY INSTRUCTIONS
FOR TODDLER RAILYOUR TR 401
(PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 401s STATIONARY CRIB”
OR TO “ASSEMBLY INSTRUCTIONS FOR YOUR 401 DROPSIDE CRIB”)
If you don’t have your assembly manual anymore, you can download a copy
from the “Assembly manuals” section of our website
or request one at
www.rominakidsfurniture.com
contact@rominakidsfurniture.com.
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
DO NOT THROW THIS INSTRUCTION BOOKLET
20 Corporation Row, Edison, NJ 088 7
Phone1(718) 478 5100, Fax (718) 478 5117
www.rominafurniture.com
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
WARNING:
.
THE PROPER USE OF THIS CRIB IS
IMPORTANT FOR YOUR BABY'S SAFETY. TO KEEP
YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH,
CAREFULLY READ AND FAMILIARIZE YOURSELF
WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE
USE
§§ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 IN BY 51 5/8 IN BY 4 IN, WITH A
THICKNESS NOT EXCEEDING 6 IN.
THE MINIMUM AGE OF YOUR CHILD SHALL NOT BE
LESS THAN 15 MONTHS AND THE MAXIMUM
WEIGHT SHALLNOTBEGREATER THAN 50LB.
FOR DROPSIDE TYPE OF 401 (older version)
STEP 1d
Completely tighten all the 4 bolts (6) which fixes the mattress support (M) to the
stabilizing bars (S) and all the 4 bolts & nuts (5+7) which fixes the metallic brackets of
the mattress support to the metallic frame.
STEP 2d
Completely tighten all the 8 Allen bolts loosened at STEP 1d and all the 4 Allen bolts
used at STEP 2d.
PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 401 DROP-SIDE CRIB”
(Two adults are required to complete this step)
2 3 S F STEP 8
D STEP 6b
(6) (M) (S)
(M) STEP 4
TR 2 1
STEP 2d
Loosen all the 8 Allen bolts ( & ) which fixes the stabilizing bars ( ) and the fixed side ( ) (see for
details).
Remove the drop-side ( ) (see for details). arefully s
Using a Phillips screwdriver (not supplied) you must completely remove all the factory mounted hardware
involved in drop-side moving, found on the end panels of your crib. You must remove:
- 2 metallic pins (from both end panels);
- 2 white plastic pins (from both end panels).
Loosen all the 4 bolts which fixes the mattress support to the stabilizing bars .
Adjust the mattress support to its lowest position (see for details).
Attach the toddler rail ( ) using 4 Allen bolts ( ) and the Allen key ( ) supplied. Start the threads by hand to
assure you don't strip the threads, then, use the Allen key.
After completing , your crib should look like the one depicted on the first page of this instruction booklet.
C
tore the drop-side in a proper place, away from
direct sunlight and moisture, taking care not to scratch the wood finish.
Remember: the resulted hardware is not a toy!
You must keep this hardware in a proper place, away from your children.
2
x 4
HARDWARE BOX CONTENT
1
2
Please locate and confirm that
you have the following parts:
TR. toddler rail = 1
one bag of hardware with the following:
. Allen wrench =
. Allen bolt (50mm - 2") = 4
1
2
1
TR
Required tools:
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver
Do not use a power screwdriver which
can cause screws to break or strip
(not
included).
Phillips screwdriver (not included)
FOR STATIONARY TYPE OF 401 (newer version)
STEP 1s
Completely tighten all the 4 bolts & washers (6+9) which fixes the mattress support
(M) to the stabilizing bars (S) and all the 4 bolts & nuts (5+9+7) which fixes the
metallic brackets of the mattress support to the metallic frame.
STEP 2s
Completely tighten all the 8 Allen bolts & washers (3+8) loosened at STEP 1s and
all the 4 Allen bolts & washers (3+8) used at STEP 2s.
PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 401s STATIONARY CRIB”
(Two adults are required to complete this step)
3+8 S F
STEP 7
3+8 STEP 6
(6+9) (M) (S)
(M) STEP 4
TR 3+8
STEP 2s
Loosen all the 12 Allen bolts & washers ( ) which fixes the stabilizing bars ( ) and the fixed sides ( )
(see for details).
Remove all the 4 Allen bolts & washers ( ) which fixes one of the fixed sides (see for details).
arefully s
Loosen all the 4 bolts & washers which fixes the mattress support to the stabilizing bars .
Adjust the mattress support to its lowest position (see for details).
Attach the toddler rail ( ) using 4 Allen bolts & washers ( ) remained from the previous step and the
Allen key supplied. Start the threads by hand to assure you don't strip the threads, then, use the Allen key.
After completing , your crib should look like the one depicted on the first page of this instruction
booklet.
C
tore the fixed side in a proper place, away from direct sunlight and moisture, taking care not to
scratch the wood finish.
HARDWARE BOX CONTENT
Please locate and confirm that
you have the following parts:
TR. toddler rail = 1
one bag of hardware with the following:
Allen wrench = 1
TR
Required tools:
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver
Do not use a power screwdriver which
can cause screws to break or strip
(not
included).
Phillips screwdriver (not included)
3
x 4
8
x 4
GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likelydamage the finish on your furniture. When placingor retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniturecausing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact withthefurniture for a long period of time,
they can cause thefinish to turn white or discolor.Alcohol or solvent containingsubstances ormaterials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture intostorage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.
Loading...