IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY INSTRUCTIONS
FOR
4501
YOUR
CONVERTIBLE CRIB
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
DO NOT THROW THIS INSTRUCTION BOOKLET
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
20 Corporation Row, Edison, NJ 088 7
Phone1(718) 478 5100, Fax (718) 478 5117
www.rominakidsfurniture.com
Europe's Kids Furniture
Furniture
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.
INFANTS CAN SUFFOCATE ON SOFT
BEDDING. NEVER ADD A PILLOW OR
COMFORTER. NEVER PLACE ADDITIONAL PADDING UNDER AN
INFANT. FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
CAUTION: ANY MATTRESS USED
IN THIS CRIB SHALL BE AT LEAST
27 BY 51 IN. WITH A THICKNESS
NOT EXCEEDING 6 IN.
- TO REDUCE THE RISK OF SIDS, PEDIATRICIANS RECOMMEND HEALTHY INFANTS BE
PLACED ON THEIR BACKSTO SLEEP, UNLESS OTHERWISEADVISED BYYOUR PHYSICIAN.
- TO HELP PREVENT STRANGULATION TIGHTEN ALL FASTENERS.A CHILD CAN TRAP PARTS
OF THE BODYOR CLOTHING ON LOOSE FASTENERS.
- PLACE CRIB NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY
STRANGLEA CHILD.
- WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD
SERVEAS STEPS FOR CLIMBING OUT.
- STOP USING CRIB WHEN CHILD BEGINS TO CLIMB OUT OR REACHES THE HEIGHT OF 35 IN.
(89 CM).
- CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, LOOSE BOLTS OR
OTHER FASTENERS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY
AND FREQUENTLY DURING USE. SECURELY TIGHTEN LOOSE BOLTS AND OTHER
FASTENERS. USE CRIB IF ANY PARTS ARE MISSING, DAMAGED OR BROKEN.
CONTACT FOR REPLACEMENT PARTS AND INSTRUCTIONAL
LITERATUREIF NEEDED. SUBSTITUTE PARTS.
- IF REFINISHING, USEA NON-TOXIC FINISH SPECIFIED FOR CHILDREN'SPRODUCTS.
- FOLLOW WARNINGS ONALL PRODUCTS IN ACRIB.
- USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS
BECAUSE THEY CANCAUSE SUFFOCATION.
- INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THATISTOO
SMALL.
STRANGULATIONHAZARD:
DO NOT
FALLHAZARD:
DO NOT
ROMINA FURNITURE
DO NOT
NEVER
- STRINGS CAN CAUSE STRANGULATION! PLACE ITEMS WITH A STRING AROUND A
CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. SUSPEND
STRINGS
OVERA CRIB ORATTACH STRINGSTO TOYS.
- READALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.
. A STORAGE POUCH & 2 PLASTIC TIES HAVE BEEN PROVIDED IN THE HARDWARE BAG.
ATTACH POUCH TO MATTRESS SUPPORT WITH PLASTIC TIES AND STORE THE
INSTRUCTIONS THERE.
- USEA WATER MATTRESS WITH THISCRIB.
- BEFORE USING THIS CRIB RECHECK ALL SCREWS AND BOLTS TO BE SURE THEY ARE
FASTENED SECURELY. A PERIODIC CHECK SHOULD BE MADE TO BE SURE THESE ITEMS
REMAIN TIGHT.
- TO AVOID HEAD INJURY, ALLOWANY CHILD TO PLAY UNDERNEATH CRIB.
DO NOT
DO NOT
KEEP INSTRUCTIONS FOR FUTURE
USE
DO NOT
DO NOT
WARNING!
CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN AYOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL.
*DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOTATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
ADRY CLOTH, WILL PRESERVE THE ORIGINALLUSTER AND BEAUTYOF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETINGTO PREVENT LEGBREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECUERLY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
DO NOT
ROMINA FURNITURE
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.
Please locate and confirm that
you have the following parts:
FB. footboard = 1
HB. headboard = 1
LP. left panel = 1
RP. right panel = 1
SB. stabilizing bars = 2
MS. mattress support = 1
WR. wooden rail = 1
one bag of hardware with the following:
1. Allen wrench =
2. one storage pouch and two plastic ties
3. Allen bolt (1 1/2" or 40 mm) =
4. Allen bolt (2 1/4" or 60 mm) = 8
5. Allen bolt (4" or 100 mm) = 4
6. round head bolt (1 3/16" or 30 mm) = 4
7. round head bolt (19/32" or 15 mm) = 4
8. "butterfly" type nut = 4
9. bigger “internal star” lock washer = 12
10. smaller “external star” lock washer = 8
1
2
Required tools:
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver
Do not use a power screwdriver which
can cause screws to break or strip
(not
included).
Note:
TIGHTEN COMPLETELY
During the assembly process whenever using screws or bolts, check
each by placing the screw / bolt on the upper diagram which is drawn in actual
size. Be sure to use the proper size and shape specified in the instructions.
Be sure to the screws / bolts when you are asked to do this.
Phillips screwdriver (not included)
RP
LP
HB
FB
1
2
8
MS
SB
WR
The item
number of your
product is located on
the inner side of the left
pannel, on a black and white
label. Please, refer to this number in
the event that you need to call ROMINA
FURNITURE or your local distributor.
Note:
Thank
you.
Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
printed in full size
3
4
7
6
8
5
10
9
9
10
STEP 1
Attach the stabilizing bars to the left and right panels
of the crib using 4 medium Allen bolts and 4
washers . Align the tenons attached at the end of the
stabilizing bars with the lower holes existing on the inner
faces of the left & right panels of the crib. Be sure that the
drilled face of the stabilizing bars faces towards the inside of
the crib (follow the instructions attached to the stabilizing bar).
Start the threads by hand to assure you don't strip the
threads, then, use the suplied Allen wrench .
Do not tighten the bolts completely at this step, you will be
asked to do this later.
(SB) (LP
& RP) (4)
(9)
(1)
FIGURE 1
REQUIRED
SB
LP
RP
SB
4+9
4+9
4+9
4+9
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
Assemble the mattress support using 4 bigger
round head bolts , 4
STEP 2
(6)
Do not tighten the bolts completely at
this step, you will be asked to do this later.
"butterfly" type nuts , 4
smaller lock washers and a Phillips
screwdriver (not supplied). The lock washer must
be attached to the bolt after the bolt passed
through the frame and the metallic bracket of the
mattress support and before attaching the nut.
(8)
(10)
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all the four bolts in the same position
(see ).FIGURE 2
NOTE: THE STYLEOF YOUR CRIB OR
OF YOUR MATTRESS SUPPORT MAY
VARY FROM WHAT IS PICTURED IN
THE INSTRUCTION SHEET
FIGURE 2
6
8
6
8
6
8
6
8
6
8
10
10
10
10
10
To adjust the vertical position of your mattress support you must remove all the four bolts & nuts
loosen all the four bolts , lower the frame and insert the bolts back into the corresponding holes,
according to the desired height (see ). Then, you must attachthe lockwashers and the nuts
as described in and tighten all the boltscompletely.
ADJUSTING THE HEIGHT OF YOUR MATTRESS SUPPORT
(6+10+8),
(7+10) (6)
FIGURE 2 (10) (8)
STEP 2
ADJUSTED THE HEIGHT OF YOUR
MATTRESS SUPPORT
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, themattress support frame must be placed directly over the stabilizing bars. Before tighten
the bolts, you must slightlypress the mattress supportframe to make sure thisposition is achieved.
WARNING:
IT'S VERY IMPORTANT TO TIGHTEN COMPLETELY ALL THE 8 BOLTS
(6+10+8) & (7+10) AFTER YOU HAVE
.
TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH,
FIGURE 3
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO
ALL THE BOLTS LISTED
IN .
TIGHTEN
COMPLETELY 8
STEP 3
the mattress support on the
stabilizing bars as these resulted after
, using the four smaller round head bolts
STEP 3
Mount (MS)
STEP
1
(7)
tighten completely 8
(6+10+8, 7+10)
FIGURE 3
all the
bolts involved in mattress
support fixing using a Phillips screwdriver
(not supplied) (see ).
, 4 washers and a Phillips
screwdriver (not supplied). The lock washer
must be attached to the bolt before inserting
the bolt through the metallic bracket of the
mattress support.
Now,
(10)
you must
REQUIRED
LP
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN COMPLETELY!
SB
RP
SB
MS
6+10+8
6+10+8
6+10+8
6+10+8
7+10
7+10
7+10
7+10
REQUIRED
y and carefully lace
it on the floor with the drilled side on top, taking care
not to scratch its finish. Then, using four medium Allen
bolts , 4 washers
attach the right and left panels as they
resulted after completing . You will have to keep
the metallic inserts side facing upward.
STEP 4 (
()
(4) (9)
(RP) & (LP)
STEP 3
Two adults are required to complete this
step)
Take the footboard of our crib pFB
Do not tighten the bolts completely at this step, you will
be asked to do this later.
and the Allen wrench supplied
,(1)
FIGURE 4
FB
LP
RP
SB
MS
metallic insertsmetallic insertsmetallic inserts
metallic inserts
metallic insertsmetallic inserts
4+9
4+9
4+9
4+9
REQUIRED
FIGURE 5
FB
HB
LP
RP
head y and
carefully lace it on the part of your crib
r Fix it
using all the 4 bigger Allen bolts , 4
washers
STEP 5 (
(H )
(5)
(9)
Two adults are required to
complete this step)
STEP 4
Take the board of our cribpB
esulted after completing .
Do not tighten these bolts completely at this
step, you will be asked to do this later.
and the Allen wrench supplied
.(1)
WARNING!
TIGHTEN COMPLETELY!
U
STEP 6
tighten
completely 4 (4+9)
FIGURE 5
all the medium Allen bolts used to fix the
stabilizing bars (see ).
sing the Allen wrench supplied,(1) you must
TIGHTEN THE SAME BOLTS ON
THE RIGHT SIDE OF YOUR CRIB!
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO
ALL THE ALLEN BOLTS
LISTED IN .
TIGHTEN
COMPLETELY 4
STEP 6
5+9
4+9
5+9
5+9
5+9
4+9
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO
ALL THE ALLEN BOLTS
LISTED IN .
TIGHTEN
COMPLETELY 8
STEP 7
FIGURE 6
REQUIRED
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN
COMPLETELY!
STEP 7
REMINDER
(Two adults are required to complete this step)
tighten
completely 8 (4+9) (5+9)
FIGURE 6
8
4 (5+9) (HB)
4 (4+9) (FB)
Turn your crib with its feet back on the floor.
U
all the Allen bolts & remained
untighten from all previous steps (see ).
You have a total of Allen bolts, distributed as following:
- bigger bolts in the headboard ;
- medium bolts in the footboard .
sing the Allen wrench supplied,(1) you must
this picture shows how your crib should look like after completing assembly
Once completed , attach the storage
pouch supplied to the mattress support
spring using two plastic ties (also supplied).
Store this instruction booklet in the storage
pouch for future use.
STEP 7
4+9
5+9
5+9
4+9
5+9
5+9
4+9
4+9
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
ASSEMBLY INSTRUCTIONS
FOR DAY BED OPTION
OF YOUR 4501
CONVERTIBLE CRIB
WARNING(FOR DAYBED OPTIONONLY):
§§ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6INCHES.
THE MINIMUM AGE SHALL NOT BE LESS THAN 15
MONTHS AND THE MAXIMUM WEIGHT SHALL NOT
BE GREATER THAN50LB.
IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
DO NOT THROW THIS INSTRUCTION BOOKLET.
STARTING FROM CRIB
FIGURE A
pull upwards after removing the Allen bolts
REQUIRED
x
x
x
x
MP
STEP A
Using the supplied Allen wrench unscrew completely all
the four Allen bolts and washers (previously mounted in
factory) located 2 by 2 on the lateral sides of the legs. Then,
remove the middle panel resulted by pulling it upwards
and then towards you (see ). Please, store the
middle panel and the four Allen bolts resulted in a proper
place, taking care not to scratch the panel finish.
(1)
(x)
(MP)
FIGURE A
FIGURE B
4
7
DETAIL C2DETAIL B2
DETAIL B1DETAIL B1
REQUIREDREQUIRED
STEP B (Two adults are required to complete this step)
()
FIGURE B
Carefully, t crib and place it with the facing the floor, taking
care not to scratch its finish (see ).
ake the footboard FB
Using the supplied Allen wrench and a Phillips screwdriver (not supplied)
unscrew completely both Allen bolts which fixes the front stabilizing bar
and both smaller round head bolts which fixes the mattress support to
the front stabilizing bar.
Rotate the front stabilizing bar by 180deg (see the and the
for the result).
Adjust the mattress support to its lowest position (see ).
(1)
(4+9) (SB)
(7+10) (MS)
white arrow DETAIL B2
STEP 2
7+10
4+9
7+10
7+10
7+10
4+9
3
3
SB
WR
FIGURE C
STEP C
(Two adults are required to complete this step)
(WR) (3)
(SB)
(4+9)
Attach the wooden rail and fix it using both smaller Allen bolts and
.
Rotate the front stabilizing bar back to its original position and fix it using both
medium Allen bolts and washers removed earlier.
removed earlier.
Turn your day bed with its feet back on the floor.
the
supplied Allen wrench
Fix the mattress support to the front stabilizing bar using both smaller round
head bolts and washers
all the bolts involved in mattress support and stabilizing bar
fixing and adjusting (see )
(1)
(MS)
(7+10)
Tighten completely
STEPS 1 to 3
Your day bed should look like the one depicted on the first page of this chapter.
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO
ALL THE BOLTS
INVOLVEDIN MATTRESSSUPPORTAND
STABILIZING BAR FIXING AND
ADJUSTING (SEE ).
TIGHTEN
COMPLETELY
STEPS 1 to 3
3
WR
DETAIL C1DETAIL C1
REQUIREDREQUIRED
WARNING!
TIGHTEN COMPLETELY!
TODDLER RAIL OPTION OF
YOUR CONVERTIBLE CRIB4501
(THE TODDLER RAIL IS SOLD SEPARATELY)
NOTE: Y
ASSEMBLY INSTRUCTIONS FOR TODDLER RAIL
CAN BE FOUND INSIDE OFTR 4501 PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR
LOCAL DISTRIBUTOR FOR MORE INFORMATION.
OU CAN ATTACH A TODDLER RAIL TO
YOUR CRIB WITH THE PURCHASE OF ROMINA
FURNITURE ITEM ( ODDLER AIL ).TR 4501 T R 4501
FULL SIZE BED OPTION OF
YOUR 4501 CONVERTIBLE CRIB
(THE CONVERSION KIT IS SOLD SEPARATELY)
NOTE:
CKC
4501 C K C 4501 .
YOUR 5501 CONVERTIBLE CRIB CAN CONVERT INTOA FULL SIZE
BED WITH THE PURCHASE OF ROMINA FURNITURE ITEM CODE
( ONVERSION IT FOR RIBS, code )
ASSEMBLYINSTRUCTIONS FOR FULL SIZE BED OPTION CAN BE FOUND
INSIDE OF CKC PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR LOCAL
DISTRIBUTOR FOR MORE INFORMATION.
GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance withtheir intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used onadult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discolorationin the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which aretoo hot or too cold directly onto the finishedsurfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to thefurniture causing
the finish to peel and thewood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor.Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact withthe finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything onit and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad'sposition frequently to avoid finish discoloration.
Regular cleaning with mild soapon asoft cloth,followed bya clean damp
cloth, thena dry cloth,will preserve the original lusterand beauty ofthis
fine finish ofyour RominaFurniture product.
Visit
for updates, special offers and more new designs.
www.rominakidsfurniture.com
Team
Thank you for beeing one of our distinguished clients.
Furniture
Loading...