NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PI CT UR ED IN THE INS TRUC TI ON SH EE T
WARNING: THE PROPER USE OF THIS CRIB IS
IMPORTANT FOR YOUR BABY SAFETY. TO KEEP
Y O U R B A B Y S E C U R E A N D S A F E ,
AND TO AVOID POTENTIAL INJURY OR DEATH,
CAREFULLY READ AND FAMILIARIZE YOURSELF
W I TH A L L WA R N I N G S, C A UT I O N S A N D
INSTRUCTIONS IN THE INSTRUCTION BOOKLET.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE
USE.
DO NOT THROW OUT THIS INSTRUCTION BOOKLET.
ASSEMBLY INSTRUCTIONS
FOR YOUR
401s STATIONARY CRIB
20 Corporation Row, Edison, NJ 088 71
Phone (718) 478 5100, Fax (718) 478 5117
www.rominafurniture.com
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISSION
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
T H E Y C A N C A U S E S U F F O C A T I O N .
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.
CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL.
*DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
A DRY CLOTH, WILL PRESERVE THE ORIGINAL LUSTER AND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECURELY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
DO NOT USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR ROMINA FURNITURE FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!
Please locate and confirm that
you have the following parts:
F. 2 fixed side =
left side = L. 1
R. 1 right side =
S. 2 stabilizing bars =
mattress support = M. 1
one bag of hardware with the following:
Allen wrench = 1. 1
one storage pouch and two plastic ties2.
Allen bolts (3. 50 mm - 1 31/32") = 12
barrel nuts = 4. 4
round head bolts (5. 30 mm - 1 3/16") = 4
round head bolts (6. 15 mm - 19/32") = 4
"butterfly" type nut = 7. 4
8. bigger “internal star” lock washer = 12
9. smaller “external star” lock washer = 8
Required tools: Allen wrench (supplied), Phillips
screwdriver (not supplied), flat screwdriver (not
supplied).
CAUTION: Do not use a power screwdriver which
can cause screws to break or strip
7 4
1
Note: During the assembly process whenever using screws or bolts, check each by
placing the screw / bolt on the upper diagram which is drawn in actual size. Be sure to
use the proper size and shape specified in the instructions.
Be sure to COMPLETELY TIGHTEN the screws / bolts when you are asked to do so.
N o t e:
T h e i t e m
number of your
product is located on
the inner side of the left
panel, on a black and white
label. Please, refer to this number
in the event that you need to call
ROM INA FURNIT URE or your l ocal
distributor.
Thank you.
Note: The letter that identify
a part is the first letter of the
respective part name (such
method is employed to
facilitate parts recognition
between the drawings and
the parts list).
Phillips screwdriver (not supplied)
L
R
F
F
M
S
S
9
8
printed in full size
3
5
6
7
4
8
9
2
STEP 1
Attach one of the stabilizing bars (S) to left side (L) of
the crib using 1 Allen bolt (3), 1 washer (8) and 1
barrel nut (4). Align the tenon attached at the end of
the stabilizing bar with the upper hole existing on the
inner face of the left side of the crib. Be sure that the
drilled face of the stabilizing bar faces towards the
inside of the crib (follow the instructions attached to
the stabilizing bar).
Push the barrel nut into the hole drilled in the
stabilizing bar then align the straight slot in the head
of the barrel nut horizontally, so the threads in the
bolt will insert in the barrel nut. You can adjust the
position of the barrel nut with a flat head screwdriver
(not supplied) or a coin.
Push the Allen bolt through the left side panel and
into the stabilizing bar. Start the threads by hand to
assure you don't strip the threads, then, use the
supplied Allen wrench.
Do not completely tighten the bolt at this step, you
will be asked to do this later.
FIGURE 1
opposite view
L
S
3
3
3
4
4
tenon
drilled
face
8
8
8
FIGURE 2
this shows how your crib should look after completing STEP 2
L
STEP 2
Repeat STEP 1 for the second stabilizing
bar.
S
S
STEP 3
Assemble the result of STEPS 1&2 with the
right side (R) of the crib using the same
technique described above.
Do not completely tighten the bolts at this
step, you will be asked to do this later.
FIGURE 3
this shows how your crib should look after completing STEP 3
L
3
S
S
R
L
S
S
R
3
4
3
4
3
8
8
8
8
LOWEST
POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST
POSITION
MIDDLE POSITION
HIGHEST POSITION
STEP 4
Assemble the mattress support using 4 bigger
round head bolts (5), 4 "butterfly" type nuts (7), 4
smaller lock washers (9) and a Phillips screwdriver
(not supplied). The lock washer must be attached
to the bolt after the bolt passed through the frame
and the metallic bracket of the mattress support
and before attaching the nut.
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all four bolts in the same position (see
FIGURE 4).
Do not completely tighten the bolts at
this step, you will be asked to do this later.
NOTE: THE STYLE OF YOUR CRIB OR
OF YOUR MATTRESS SUPPORT MAY
VARY FROM WHAT IS PICTURED IN
T H E I N S T RU C T I O N S H EE T
FIGURE 4
5
7
5
7
5
7
5
7
5
7
9
9
9
9
9
A D J U S T I N G T H E H E I G H T O F Y O U R M AT T R E S S S U P P O R T
To adjust the vertical position of your mattress support you must remove all four bolts & nuts (5+9+7), loosen
all four bolts (6+9), lower the frame and insert the bolts (5) back into the corresponding holes, according to the
desired height (see FIGURE 4). Then, you must attach the lock washers (9) and the nuts (7) as described in
STEP 4 and completely tighten all the bolts.
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the stabilizing bars. Before tighten
the bolts, you must slightly press the mattress support frame to make sure this position is achieved.
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL THE 8 BOLTS
(5+9+7) & (6+9) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.
STEP 5
Mount the mattress support on the stabilizing bars as these
resulted after STEP 3, using 4 smaller round head bolts (6),
4 washers (9) and a Phillips screwdriver. The lock washer
must be attached to the bolt before inserting the bolt
through the metallic bracket of the mattress support.
Now, you must completely tighten all 8 bolts (5+9+7, 6+9)
involved in mattress support fixing using a Phillips
screwdriver (not supplied) (see FIGURE 5).
FIGURE 5
6
7
5
6
7
5
6
7
5
6
7
5
6
WARNING: TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
VERY IMPORTANT COMPLETELY TO
TIGHTEN ALL 8 BOLTS LISTED IN STEP 5.
9
9
9
9
9
9
9
9
9
WARNING!
COMPLETELY TIGHTEN!
WARNING!
COMPLETELY TIGHTEN!
FIGURE 6
STEP 6
- position one fixed side (F) with the rounded
horizontal rail on top then attach it to the part
of your crib resulted after STEP 5, using 4
Allen bolts (3), 4 washers (8) and the Allen
wrench supplied (1);
- do the same for the second fixed side ;(F)
Do not completely tighten the bolts at this
step, you will be asked to do this later.
rounded side
3
3
3
3
F
L
R
F
3
3
3
3
8
8
8
8
8
8
8
8
FIGURE 7
WARNING!
TIGHTEN COMPLETELY!
STEP 7
Now, using the Allen wrench (1) supplied, you
must completely tighten all the bolts (3+8)
which remained not tightened from all
previous steps (see FIGURE 7).
REMINDER
You have a total of 12 bolts, distributed as
following:
- 8 bolts (3+8) in the fixed sides (F);
- 2 bolts (3+8) in the bottom part of left side
(L);
- 2 bolts (3+8) in the bottom part of right
side (R).
3
3
3
3
3
3
WARNING: TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
VERY IMPORTANT COMPLETELY TO
TIGHTEN ALL 12 ALLEN BOLTS LISTED
IN STEP 7.
3
3
3
3
3
3
8
8
8
8
8
8
8
8
8
8
8
8
this shows how your crib should look after completing assembly
After you completed , attach the STEP 7
storage pouch supplied to the mattress
support spring using the two plastic ties
supplied. Store this instruction booklet in the
storage pouch for future use.
TODDLER RAIL OPTION OF YOUR 401s
STATIONARY CRIB (SOLD SEPARATELY)
YOU CAN ATTACH A TODDLER RAIL TO YOUR CRIB
WITH THE PURCHASE OF ROMINA FURNITURE ITEM
TR 401 (TODDLER RAIL 401).
ASSEMBLY INSTRUCTIONS FOR TODDLER RAIL CAN BE
FOUND INSIDE OF TR 401 PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR
LOCAL DISTRIBUTOR FOR MORE INFORMATION.
GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina Furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.
Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of the
fine finish of your Romina Furniture product.
Visit
www.rominafurniture.com
for updates, special offers and more new designs.
Team
Thank you for being one of our distinguished clients.
Loading...