Romina 11510 Assembly Instructions Manual

ASSEMBLY INSTRUCTIONS

FOR YOUR

11510 STATIONARY CRIB

20 Corporation Row, Edison, NJ 088 7

Phone[phone], Fax [phone]

www.rominafurniture.com

IMPORTANT: PLEASE, READ ALL

INSTRUCTIONS BEFORE

ASSEMBLING! PLEASE, SAVE

INSTRUCTIONS FOR FUTURE USE

* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESSTHAT IS TOOSMALL.

WARNING: THE PROPER USE OF THIS CRIB IS IMPORTANTFOR

YOUR BABY'S SAFETY. TO KEEP YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH, CAREFULLY READ
AND FAMILIARIZE YOURSELF WITH ALLWARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET. KEEP THIS
INSTRUCTION BOOKLET FOR FUTURE USE.

NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

THIS CRIB CONFORMS TO APPLICABLE

REGULATIONS PROMULGATED BY THE

CONSUMER PRODUCT SAFETY COMMISSION

this picture shows how your crib

should look like after completing assembly

CAUTION:

*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH OR

REGULAR BED.

*USE OF A VAPORIZERNEAR FURNITURE WILL CAUSE WOODTO SWELLAND FINISH TO PEEL.

*DO NOT STORE CRIB INAREAS WHERE TEMPERATURESAND CONDITIONS ARE EXTREME, SUCH

AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS MAY

CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN STRUCTURAL

FAILURE.

*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE MANUFACTURER

WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR CLEANING WITH MILD

SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN A DRY CLOTH, WILL

PRESERVE THE ORIGINAL LUSTER AND BEAUTY OFTHIS FINE FINISH.

*THIS CRIB ISNOTEQUIPPED TO HANDLE THE EXCESSWEIGHTOFACRIB WATER MATTRESS.

*LIFT SLIGHTLYWHEN MOVING ON CARPETINGTO PREVENTLEG BREAKAGE.

ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING

REGULARLY, BEFORE PLACING THE CHILD IN THE CRIB, THAT

EVERYCOMPONENT IS PROPERLYAND SECURELYIN PLACE.

MAINTENANCE OF YOUR ROMINACONVERTIBLE CRIB:

DO NOT

ROMINA FURNITURE

NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO YOUR

CRIB!

AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THATALL

BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST CHECK

ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS NECESSARY.

PERIODICALLY INSPECT CRIB FOR DAMAGED HARDWARE,

LOOSE JOINTS OR SPLINTERED EDGES.

USE CRIB IF PARTS ARE DAMAGED OR BROKEN!

CONTACT YOUR DEALER OR FOR

ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE TO

HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU MAKE

CONTACT. THE MODEL CODE CAN BE FOUND ON A WHITE LABEL

LOCATED ON THE INSIDE OF YOUR CRIB ON THE SIDE PANEL.

11510 BOX CONTENT

Please locate and confirm that
you have the followingparts:

EP.
SS.

MS.

end panel = 2

stationary side = 2

mattress support = 1

BF.

DL.

1.

2.

5.

6.

7.

8.

9.

Required tools:

CAUTION:

bottom frame = 1

decorative leg = 4

and one bag of hardware with the following:

Allen wrench =

one storage pouch and two plastic ties

rounded head bolt (30mm - 1 1/8") = 4
rounded head bolt (15mm - 5/8") = 4
"butterfly" type nut = 4
“internal star” lock washer = 26
“external star” lock washer = 8

Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver (not
included).

Do not use a power screwdriver which can

cause screws to breakor strip.

1

3.4.Allen bolt (40mm - 1 5/8" - w/o centering tip) = 14

Allen bolt (20mm - 3/4" - w/o centering tip) = 12

Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).

printed in full size

1

Note:

TIGHTEN

During the assembly process whenever using screws or
bolts, check each by placing the screw / bolt on the hardware
diagram which is drawn in actual size. Be sure to use the proper
size and shape specified in the instructions. Be sure to

the screws / bolts when you are

asked to do this.

COMPLETELY

Note: The item number of your product is
located on the inner side of the left panel,
on ablack and white label.Please, refer to
this number in the event that you need to
call ROMINA FURNITURE or your local
distributor.Thank you.

3

4

5

6

7

8

9

EP

EP

SS

SS

BF

DL

MS

Phillips screwdriver (not included)

NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

FIGURE 1

STEP 1

(Twoadults are required to complete this step)

(SS) (EP) (3) (8)Attach the stationary sides to the end panels using eight biggerAllen bolts , eight bigger washers

and the Allen key. Take care to insert thewasher between the bolt and the stationaryside vertical post!

Do not completely tightenthe bolts at this step, you will beasked to do this later.

3

x 8

8

x 8

3+8

3+8

3+8

3+8

3+8

3+8

3+8

3+8

EP

SS

SS

EP

REQUIRED

NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

FIGURE 2

STEP 2

REMINDER

(Twoadults are required to complete this step)

(BF) (SS)

(EP) (3) (8)

(DL) 12

(4) 12 (8)

Completely tighten 14 (3+8) 12

(4+8)

14 12

8 (3+8)
6 (3+8)
12 (4+8)

Turn the crib upside down, taking carenot to scratch its finish.

Attach the base frame to the stationary sides and to the end
panels using six bigger Allen bolts , six bigger washers and
the Allen key. Take care to insert the washer between the bolt and the
base frame wooden components!

Attach the decorative legs to the crib using smaller Allen bolts

, washers and the Allen key. Take care to insert the washer

between the bolt andthe metallic plate!

all bigger Allen bolts and all smaller

Allen bolts used before.

Turn the crib in its normal position,taking care not to scratch its finish.

You have to completely tighten bigger Allen bolts and smaller
Allen bolts, distributed asfollowing:

- bigger bolts in the stationary sides;

- bigger bolts in the base frame;

- smaller bolts in the decorativelegs.

BF

DL

DL

DL

DL

3+8

4+8

3+8

3+8

3+8

3+8

3+8

4+8

4+8

4+8

4

x 12

8

x 12

3

x 6

8

x 6

NOTE: THE STYLE OF YOUR CRIB,

METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

WARNING:

VERY IMPORTANT

TIGHTEN 26

STEP 2.

TO KEEP YOUR BABY SECURE AND

SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S TO

ALL BOLTS LISTED

IN

COMPLETELY

REQUIRED

WARNING!

COMPLETELY TIGHTEN!

LOWEST POSITION

MIDDLE POSITION

HIGHEST POSITION

LOWEST POSITION

MIDDLE POSITION

HIGHEST POSITION

Assemble the mattress support using 4 bigger round head
bolts , 4

STEP 3 (One adult is required to complete this step)

(5)

"butterfly" type nuts , 4 smaller lock washers

and a Phillips screwdriver(not supplied).
The lock washer must be attached to the bolt after the bolt
passed through the frame and the metallic bracket of the
mattress support and beforeattaching the nut.

There are three positionsfor the mattress support (from

the highest one fora newborn to the lowest one for a
child that is maximum35" tall - see caution note). You
must adjust the heightof the mattress support
depending of your childheight by inserting all

four bolts in thesame position (see ).

(7)

(9)

FIGURE 3

Do not completely tightenthe bolts at
this step, you willbe asked to do this later.

FIGURE 3

To adjust the vertical position of your mattress support you must remove the mattress support from the crib

remove all four bolts & nuts , lower the frame and insert the bolts back into
the corresponding holes, according to the desired height (see ). Then, you must attach the lock
washers and thenuts as described in , attach the mattress support to thecrib

and tighten all the bolts.

ADJUSTING THE HEIGHT OF YOUR MATTRESS SUPPORT

(please see ),

(please see

) completely

Your crib is designedin such a mannerthat, when the mattress support is adjusted to it’s lowest position, the
mattress support frame must be placed directly over the bottom frame. Before tightening the bolts, you must
slightly press the mattresssupport frame to make sure this position isachieved.

TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR

DEATH,

STEP 4

STEP

4

(5+9+7) (5)

FIGURE 3

(9) (7) STEP 3

WARNING:

IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL 8 BOLTS (5+9+7) &
(6+9) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.

5

x 4

9

x 4

7

x 4

5+9+7

5+9+7

5+9+7

5+9+7

5+9+7

REQUIRED

NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

WARNING!

COMPLETELY TIGHTEN!

FIGURE 4

STEP 4

REMINDER

(Twoadults are required to complete this step)

(MS) (BF)

(6)

Completely tighten 8 (5+9+7, 6+9)

8

4 (5+9+7)
4 (6+9)

Attach the mattress support to the bottom frame using
four smaller rounded head bolts

all bolts involved in mattress

support fixing using aPhillips screwdriver (not supplied).

You have to completely tighten rounded head bolts, distributed
as following:

- bolts in the mattress support;

- bolts in the bottomframe.

A

After completing assembly, your crib should look like the one
depicted on the firstpage of this manual

, four smaller washers and
a Phillips screwdriver (not supplied). The lock washer must be
attached to the bolt before inserting the bolt through the metallic
bracket of the mattresssupport.

ttach the storage pouch supplied to the mattress support spring
using twoplastic ties (also supplied). Store this instruction booklet
in the storage pouchfor future use.

(9)

.

6+9

6+9

6+9

6+9

5+9+7

5+9+7

5+9+7

5+9+7

MS

WARNING!

COMPLETELY TIGHTEN!

5

x 4

8

x 4

NOTE: THE STYLE OF YOUR CRIB,

METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

WARNING:

VERY IMPORTANT

TIGHTEN

STEP .

TO KEEP YOUR BABY SECURE AND

SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S TO

ALL BOLTS LISTED

IN

COMPLETELY 8

4

REQUIRED

GENERAL FURNITURE CARE TIPS

· Wood, like any natural material is likely to present variations of grain and texture which will result in

slight color variations or richness in the finish. These differences make each Romina Furniture item as

beautiful and unique as you and your baby are.

· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture

items be usedin accordance with theirintended design.

· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be

more delicate thanthose used on adultfurniture thus requiring carefulmaintenance.

· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers

or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,

always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces

must be moved/rotatedto prevent discoloration inthe finish.

· Exposure to extreme variations of environmental conditions such as humidity and temperature can

affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room

temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.

Do not placeitems which are toohot or too colddirectly onto the finishedsurfaces!

· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing

the finish topeel and the woodto warp.

· Wipe up spills promptly. If water or other liquids stayin contact withthe furniture for a long period of time,

they can cause the finish to turn white or discolor.Alcohol or solvent containing substances or materials will

permanently damage thefinish.

· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,

heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and

smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will

yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that

all wood essences will darken over time along with the natural aging process which is not considered to be

a quality defect.

· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow

water to stayin contact with thefinish as it willdamage the finish.

· If you need to put your furniture into storage for any period of time, avoidplacing it in damp basements or

hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to

walls, do notstack anything on itand do not coverit entirely.

· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt

underneath. Certain plastics have ingredients that can react with and damage the finish. It is

recommended to rotatethe changing pad's positionfrequently to avoid finishdiscoloration.

Regular cleaning withmild soap on asoftcloth,followedby a clean damp
cloth, then adry cloth, will preserve theoriginal luster and beauty ofthe
fine finish of your Romina Furniture product.

Visit

for updates, special offers and more new designs.

www.rominafurniture.com

Team

Thank you for being one of our distinguished clients.

Furniture