RP221
Bottom Feeder
Crossover / Sonic exciter
ROLLS CORPORATION
SALT LAKE CITY, UTAH
5/04
12 VDC
INPUT LEVEL
000
ACTIVE
clip
20
MADE IN
USA
SERIAL NUMBER
221-
BOTTOM DEFINITION XOVER FREQ
- + - +
SUB
HIGH
OUT
OUTPUT
30
LEFT
RIGHT
558090
40
27
Hz 0
25
LOOP
THRU
140
OWNERS MANUAL
SUB OCTAVE
SYNTH LEVEL
100
120
130
INPUT
0
SUB
LEVEL
10 10dB
MODEL RP221
pwr
RP221
INTRODUCTION
Congratulations and thank you for your purchase of the RP221 Bottom Feeder Crossover, sub-sonic synthisizer, and Sonic Exciter. The outputs are not only
separate high and low frequencies, but enhanced for crystal clear highs and lows
worthy of Richter scale measurements. You’ve now got complete control over the
tone of your sound.
Please review this manual carefully as it contains the information necessary for
the proper setup and operation of your new RP221 Bottom Feeder.
THE ROLLS SONIC EXCITER - SCE PROCESSING
The human ear can detect a frequency range of roughly 20Hz to 20kHz. However,
the frequency response that a normal speaker can effectively reproduce is much,
much less. Additionally, speakers add distortion and phase changes that make the
sound quite different from that of the original material.
A sonic exciter restores clarity and presence to the processed signal by correcting
phase changes and harmonic structure differences. In other words, it puts the
components of the sound back where they belong.
LIMITED WARRANTY
This product is warranted to the original consumer purchaser to be free from
defects in materials and workmanship under normal installation, use and service for a
period of one (1) year from the date of purchase as shown on the purchaser’s receipt.
The obligation of Rolls Corporation under this warranty shall be limited to repair
or replacement (at our option), during the warranty period of any part which proves
defective in material or workmanship under normal installation, use and service, provided
the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PRE-
PAID. Products returned to us or to an authorized Service Center must be accompanied by
a copy of the purchase receipt. In the absence of such purchase receipt, the warranty
period shall be one (1) year from the date of manufacture.
This warranty shall be invalid if the product is damaged as a result of deface-
ment, misuse, abuse, neglect, accident, destruction or alteration of the serial number,
All of this magic is done by the use of all-pass filtering, frequency compensated
gain adjustment, and compensated frequency domain delay. What this means to
you is the elements of your sound are fanned out like a deck of cards, making
each sound more audible and distinct, reducing the need for high volume and
radical equalizer adjustment.
TABLE OF CONTENTS
Introduction 1
Table of Contents 1
Inspection 2
Specifications 2
Descriptions
Front Panel 3
Rear Panel 3
Connection 4
Operation 4
Schematic 5
improper electrical voltages or currents, repair, alteration or maintenance by any person or
party other than our own service facility or an authorized Service Center, or any use
violative of instructions furnished by us.
This one-year warranty is in lieu of all expressed warranties, obligations or
liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN
LIMITED WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow
the exclusion or limitation of special, incidental or consequential damages so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
Warranty 6
1 6
SCHEMATIC
INSPECTION
1. Unpack and inspect the RP221 box and package.
If obvious physical damage is noticed, contact the carrier immediately to make a
damage claim. We suggest saving the shipping carton and packing materials for
safely transporting the unit in the future.
2. Please complete the Warranty Registration Card and return it to the factory.
SPECIFICATIONS
Frequency Response: 20Hz to 40kHz
Input Impedance: 10KΩ unbalanced
THD + Noise: <0.07% typical
Noise Floor: -78 dB
Indicators: Power LED
Clip LED
Input/Output jacks 4: Stereo RCA jacks
Dimensions:
Weight: 4 lbs.
Power: 12 VDC (Rolls Model PS27)
25
FRONT PANEL DESCRIPTION
INPUT LEVEL
000
ACTIVE
clip
20
BOTTOM DEFINITION XOVER FREQ
- + - +
558090
40
30
27
25
100
120
130
Hz 0
140
SUB OCTAVE
SYNTH LEVEL
0
10 10dB
SUB
LEVEL
pwr
RP221
CONNECTION
Connect your RP221 to the signal source you want processed such as a DJ mixer
or Karaoke unit output for example. Connect the High Outputs to an amplifier and
speaker combination designed to receive signals above at least 140 Hz. Connect
the Sub Outputs to an amplifier/speaker combination designed to receive signals
below 140 Hz. Remember to consult the speaker manufacturers owners manuals
for proper crossover settings.
INPUT LEVEL: Adjusts the amount of input signal to the RP221.
CLIP LED: Indicates overload in the input circuitry. If this LED lights, the INPUT LEVEL
should be reduced.
ACTIVE switch: When pressed in, the sonic exciter and sub-synth circuits are engaged.
BOTTOM: Controls the low frequency cut/boost (flat or no cut/boost is at about 11
O’clock). There is a 0 to 1/2 turn spectrum spread from mid-range to bass with this control
as well as amplitude control.
DEFINITION: Controls the amount of sonic clarity (sibilance) and sound spread. Setting it
at 0 is flat response and minimal spread, 10 is maximum spread and definition.
XOVER FREQUENCY: Sets the frequency point at which the high and low frequencies
are split. The frequencies above the crossover point are sent to the High Outputs, the
frequencies below this point are sent to the Sub Outputs.
SUB OCTAVE SYNTH LEVEL: Adjusts the amount of signal coming from the Sub-Octave
synthesizer circuitry. The Sub-Octave Synth is a special circuit that divides the low
frequency signal (after the crossover) in half, and produces a sub-octave harmonic. This
level control then mixes the resulting signal with the Sub Level signal.
SUB LEVEL: Adjusts the output level from the Sub Outputs. This includes the low frequencies after the crossover, and the added Sub Octave Synth signals.
PWR LED: Indicates that the RP221 is connected to the power adapter, and to an AC
outlet.
REAR PANEL DESCRIPTION
12 VDC
MADE IN
USA
SERIAL NUMBER
221-
SUB
OUT
HIGH
OUTPUT
LEFT
RIGHT
LOOP
THRU
INPUT
MODEL RP221
OPERATION
SETTING THE INPUT LEVEL
After proper setup and connection, play a sample of program material, and test any
microphones for a normal operating output level. Adjust the RP221 INPUT LEVEL control
to the point where the CLIP LED begins to light, then back off this control slightly until the
CLIP LED only lights occasionally.
SETTING THE CROSSOVER
The XOVER FREQ control sets the frequency point at which the high and low frequencies
are split. The frequencies above the crossover point are sent to the HIGH OUTPUT, the
frequencies below the crossover point are sent to the SUB OUTPUT.
Consult the subwoofer speaker(s) owners manual for the suggested crossover frequency.
THE SONIC EXCITER
The two controls that make up the Sonic Exciter section of the RP221 are the Bottom and
Definition. Start by setting these two controls at the 12 O’clock position. Turning the
Bottom control clockwise increases the amount of sub-frequency enhancement, thereby
increasing the level of low frequency sound. Turning the Definition control clockwise
increases the high frequency enhancement, and increases the amount of high frequency
sound (often referred to as sibilance or “sizzle”). Set each of gthese for the desired
process amount.
THE SUB OCTAVE SYNTHESIZER/SUB LEVEL
This control will effect the Sub Output signal only, and must be set carefully. Increasing
the amount of the Sub Octave Synthesizer adds extreme low frequencies to the sound.
Begin with this control set at 0. With program material playing, slowly and carefully
increase the Sub Octave Synth Level until you hear the desired amount of low-end
enhancement.
Finally, adjust the Sub Level control to match the level of the High Frequency output for
the desired mix of frequencies.
12 VDC: Connects to the Rolls PS27 (12 VDC, 150 mA, tip negative) power supply.
SUB OUT: Mono summed, dual RCA jacks containing the low frequencies (from the
crossover frequency and below) portion of the signal.
HIGH OUTPUT: Stereo RCA jacks containing the high frequencies (from the crossover
frequency and up) portion of the output signal.
LOOP THRU: Stereo RCA jacks directly connected to the INPUT jacks.
INPUT: Stereo RCA for connection to the signal source.
CAUTION: TO AVOID POSSIBLE SPEAKER OR AMPLIFIER
DAMAGE, ALWAYS TURN ON THE RP221 AND OTHER PERIPHERAL EQUIPMENT BEFORE TURNING ON THE POWER AMPLIFIERS.
ALSO TURN OFF THE POWER AMPLIFIERS FIRST, BEFORE
TURNING OFF THE RP221 AND OTHER EQUIPMENT.
3 4
Loading...