Page 1
75889 00851
6 7
SPECIFICATIONS
Input Impedance: Mic: 600 Ohms XLR balanced
Line: 22K Ohms RCA
Max Input Level: Mic: -14 dBV Mic level
Line: +24 dBV
Total input Connectors: 4: XLR, 4: Stereo 1/4", 1: 3.5mm
Phantom Power: +48 VDC
RCA Output Level: +17 dBV max (impedance 1K Ohm)
Max Gain: Mic: 70 dB
Source: 30 dB
Noise Floor: - 80 dB, THD: <.025%,
S/N Ratio: 96 dB
Voltage Gain: 32 dB
Nominal Supply Voltage: 15 VDC
Bandwidth: 20Hz - 25 kHz
Size: 19” x 1.75” x 4” (48.3 x 4.5 x 10 cm)
Weight: 7 lbs. (2.3 kg)
Power supply: Rolls PS27s power supply 15 VDC 500 mA TIP NEGATIVE.
INSPECTION / WARRANTY
1. Unpack and inspect the RM85 box and package.
If obvious physical damage is noticed, contact the carrier immediately to make a
damage claim. We suggest saving the shipping carton and packing materials for safely
transporting the unit in the future.
2. Please visit our web site at www.rolls.com and click on the Register Your Warranty
Here button, or complete the Warranty Registration Card and return it to the factory.
RM85
2 ZONE
Mic/Line Mixer
OL
OL
OL
3
A+B
A B
SIG SIG
ASSIGN
8 7
B ABAB AB
MADE IN USA
4 5
A B
LINE INPUTS
A
A+B
OL
A+B
ASSIGN
6
OL
B
A
A
ASSIGN
ASSIGN
STEREOSTEREO
MODEL RM85
www.rolls.com
5
PHANTOM
ON
4
A+B
A+B
OL
B
B
A
ASSIGN
STEREO
STEREO
3
4
MIC / LINE INPUTS
7 8
6
www.rolls.com
MADE IN USA
ROLLS PS27s
15 VDC
OL
SIG
+
-
1
A+B
A B
SIG
ASSIGN
B A
OUTPUTS
2
A+B
A B
ASSIGN
FEATURES
- Four XLR balanced inputs with +48 V phantom power
- Four stereo Source inputs, including a front panel 3.5mm input
- Master Output Level control for each channel
- Low noise, ecient operation
- All in a single rack space
The RM85 is a 8 channel two zone mixer. Channels 1-4 will accommodate XLR microphone or XLR line level inputs. Channels 5-8 are 1/4"
inputs. All 8 channels can be sent to the two XLR outputs in three congurations; A, B or both A+B. The separate A and B outputs are XLR and
either can be selected to be Line or Microphone level output. Channel
8 also has a stereo 3.5mm (1/8") input on the front of the RM85.
OUTPUTS
A B
STEREO
OL
OL
A+B
OL
LINE
INPUT
B
A
ASSIGN
2
MIC/LINE
MIXER
RM85
1
Salt Lake City, Utah
1/18
Quick Start Guide
Page 2
NOTE: THIS MANUAL ASSUMES THE USER HAS A WORKING KNOWLEDGE OF AUDIO ELECTRONICS, BALANCED AND UNBALANCED
MIC/LINE
MIXER
RM85
STEREO
STEREO
STEREOSTEREO
OL
OL
1
2
OL
OL
OL
OL
3
4 5
6
7 8
A B
SIG
SIG
SIG SIG
OL
OUTPUTS
A B
ASSIGN
A+B
A B
ASSIGN
A+B
A B
ASSIGN
A+B
A B
ASSIGN
A+B
A
B
ASSIGN
A+B
OL
A
B
ASSIGN
A+B
OL
A
B
ASSIGN
A+B
OL
A
B
ASSIGN
A+B
STEREO
INPUT
LINE
CONNECTIONS, AND PROPER SIGNAL LEVEL SETTING.
Channel 5-8
LEVEL adjusts the level of the channel. The ASSIGN selector switch will send the channel signal
Channel 1-4
LEVEL adjusts the level of the channel. The
ASSIGN selector switch will send the channel signal out to A, B or both A+B.
out to A, B or both A+B. The STEREO switch is
for selecting the desired input conguration as
described below. If the stereo switch is "in" the
A and B inputs and outputs are independent of
each other. If the stereo switch is "out" the A and
B inputs are summed to mono.
Output LEVEL
Independently adjusts
the output sent to A or B
outputs.
OL
1
www.rolls.com
MADE IN USA
ROLLS PS27s
15 VDC
SIG
B A
+
-
XLR A and B
outputs
Balanced XLR output
selectable to be line or
mic level by the corresponding switch to
each channel.
DC power jack
For connection to the supplied
Rolls PS27s power supply 15 VDC
500 mA TIP NEGATIVE.
OL
A+B
A B
ASSIGN
OUTPUTS
2
SIG
A+B
A B
ASSIGN
MADE IN USA
OL
3
A+B
SIG SIG
A B
ASSIGN
8 7
A
B AB
Channel 1-5 inputs
1/4" mono (tip, sleeve) for the A
and B inputs. If you have only a
single mono input plug it into
either the A or B jack and set the
"STEREO" button so that it is in
the outward position on the front
panel. This will sum the signal to
mono, and send it to both A, B or
both A+B as selected on the front
pannel ASSIGN switch.
OL
4 5
A B
ASSIGN
LINE INPUTS
A+B
B AB
A+B
OL
A
ASSIGN
6
A
6
A+B
B
STEREOSTEREO
5
OL
A
ASSIGN
MODEL RM85
www.rolls.com
PHANTOM
ON
4
7 8
B
STEREO
4
A+B
OL
B
A
ASSIGN
STEREO
STEREO
A+B
OL
LINE
INPUT
B
A
ASSIGN
3
MIC / LINE INPUTS
DIP SWITCH SETTINGS
- PHANTOM POWER: If
a microphone requires
phantom power, move the
Mic channel’s corresponding PHANTOM POWER DIP
OUTPUTS
A B
OL
OL
2
1
Channel 1-4 inputs
XLR balanced inputs. Mic or
Line level can be selected for
each input separately by the
corresponding switch next to
the XLR jack.
MIC/LINE
MIXER
RM85
switch to the down position. This applies +48 volts
phantom power to the
indicated microphone.
Loading...