LIMITED WARRANTY
This product is warranted to the original consumer purchaser to be free from
defects in materials and workmanship under normal installation, use and service for a
period of one (1) year from the date of purchase as shown on the purchaser’s receipt.
The obligation of Rolls Corporation under this warranty shall be limited to repair
or replacement (at our option), during the warranty period of any part which proves
defective in material or workmanship under normal installation, use and service, provided
the product is returned to Rolls Corporation, TRANSPORT ATION CHARGES PREPAID. Products returned to us or to an authorized Service Center must be accompanied by
a copy of the purchase receipt. In the absence of such purchase receipt, the warranty
period shall be one (1) year from the date of manufacture.
This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number,
improper electrical voltages or currents, repair, alteration or maintenance by any person or
party other than our own service facility or an authorized Service Center, or any use
violative of instructions furnished by us.
This one-year warranty is in lieu of all expressed warranties, obligations or
liabilities. ANY IMPLIED W ARRANTIES, OBLIGATIONS, OR LIABILITIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN
RA62b
Six Channel
Stereo Headphone Amplifier
LEVELLEVEL
OUTPUT
LEVELLEVEL
OUTPUT
STEREO
LEVELLEVEL
MONO
L R
PAN
OUTPUT
STEREO
INPUT
OUTPUT
LEVELLEVEL
LEVELLEVEL
6 CHANNEL
HEADPHONE AMPLIFIER
pwr
RA62b
OUTPUT
OUTPUT
LEVELLEVEL
LIMITED WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY , EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow
the exclusion or limitation of special, incidental or consequential damages so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
ROLLS CORPORATION
SAL T LAKE CITY, UTAH
5/03
LEFT INPUTS
LEFT/MONO
INPUT
RIGHT/STEREO
INPUT
FRONT PANEL
STEREO IN
RIGHT INPUTS
INSERT
L
PAN
INSERT
R
TO CHANNELS
3 THROUGH 6
R
L
R
L
CHANNEL ONE
1/4" OUT
CHANNEL ONE
1/8" (3.5 mm) OUT
CHANNEL TWO
HEADPHONE OUT
CHANNEL TWO
1/8" (3.5 mm) OUT
OWNERS MANUAL
TABLE OF CONTENTS
SPECIFICASPECIFICA
SPECIFICA
SPECIFICASPECIFICA
TT
II
OO
NSNS
T
I
O
NS
TT
II
OO
NSNS
Table of Contents 1
Warnings 1
Inspection 1
Introduction 2
Features 2
Description
Front P anel 3
Rear Panel 3
Connection 4
Schematic 5
Specifications 6
Warranty Back Cover
These symbols are internationally accepted symbols that warn of potential
hazards with electrical products.The lightning flash means that there are
dangerous voltages present within the unit.The exclamation point indicates
that it is necessary for the user to refer to the owners manual.
Input Impedance: 10K Ω unbalanced
Max Input Lev el: +18 dBV
Input Connectors: 1/4" TRS stereo, R & L unbalanced 1/4"
and RCA, R & L balanced XLR
6: 1/4" TRS insert jacks
Outputs: 6: 1/4" TRS Stereo jacks
6: 1/8" (3.5 mm) TRS Stereo jacks
Max Gain: 20 dB/Channel
Max Output Power: up to 300 mW/side, 600 mW/Channel
( @ 16 Ohms )
Frequency Response: DC - 30 kHz
S/N Ratio: 90 dB
THD: <.008%
IMD: <.008%
Phase Shift (In to Out): 0 deg.
Slew Rate: 25 V/µ Second
Crosstalk: - 65 dB
Power 120 VAC 50-60 Hz, 15 VA
Weight: 7 lbs (3KG)
Size: 19" x 1.75" x 6.5" (48cm x 4.5cm x 17cm)
These symbols warn that there are no user serviceable parts inside the unit.
Do not open the unit. Do not attempt to service the unit yourself . Refer all
servicing to qualified personnel. Opening the chassis for an y reason will void
the manufacturer’s warranty. Do not get the unit wet. If liquid is spilled on
the unit, shut it off immediately and take it to a dealer for service.
Disconnect the unit during storms to prevent damage.
INSPECTION
1. Unpac k and inspect the RA62 bo x and pac kage .
If obvious physical damage is noticed, contact the carrier immediately to make a
damage claim. We suggest saving the shipping carton and packing materials for
safely transporting the unit in the future.
2. Please visit our w ebsite at www.rolls.com and click on the Register Your
Warranty Here te xt. Fill out the warranty information to ensure cov erage of y our
new RA62b . If you do not hav e access to the internet, or do not wish to register
your warranty online, complete the Warranty Registration Card and return it to the
factory.
1
6
SCHEMATIC
INTRODUCTION
Thank you for y our purchase of the Rolls RA62b Stereo Headphone Amplifier.The
ROLLS RA62b is a six-channel headphone/earphone amplifier for professional
audio monitoring. It is intended f or recording studios, sound reinf orcement, and
audiophile listening environments where full frequency response signal(s) are to
be distributed to up to six individuals. A v ariety of input options are av ailab le
including 1/4", RCA, and balanced XLR. Since the MONO/STEREO s witch is after
the pan control, it will mix 2 MONO signals and their balance can be adjusted with
the Pan control. Up to six individual monitor mixes may be listened to via the rear
panel insert jacks. The RA62b features a FR4 double sided circuit board, sock eted
integrated circuits, and painted steel chassis.
This manual assumes the user has a basic knowledge of audio electronic equipment.
FEATURES
• 6: 1/4" Headphone and 6: 1/8" (3/5 mm) Earphone Outputs per channel with
Level Controls
• 1/4" and 1/8" Outputs may be used simultaneously
• 1/4", RCA and XLR Inputs
• 6 TRS Stereo Insert jacks for separate use of each channel
• Up to 600 mW output per jack - it's loud
• Stereo/Mono Switch - allows mixing 2 mono signals
• Front and rear panel input jac ks
• May be used as a six channel Distribution Amplifier
• FR4 Double-sided fiberglass epoxy circuit board
• Socketed ICs
• Made in the U.S .A.
WARNING
USING THIS SYSTEM AT EXCESSIVE V OLUMES CAN CAUSE
PERMANENT HEARING DAMA GE.
USE AS LOW A VOLUME AS POSSIBLE
In order to use this system safely, avoid prolonged listening at excessive sound
pressure levels. Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure to sound
pressure levels before hearing damage occurs.
90 dB SPL at 8 hours
95 dB SPL at 4 hours
100 dB SPL at 2 hours
105 dB SPL at 1 hour
110 dB SPL at 1/2 hour
115 dB SPL at 15 minutes
120 dB SPL -
5
avoid or damage ma y occur
2
DESCRIPTION
CONNECTION
FRONT PANEL
PAN
STEREO
OUTPUT
OUTPUT
LEVELLEVEL
OUTPUT
LEVELLEVEL
OUTPUT
LEVELLEVEL
OUTPUT
LEVELLEVEL
LEVELLEVEL
OUTPUT
MONO
STEREO
LEVELLEVEL
INPUT
L R
6 CHANNEL
HEADPHONE AMPLIFIER
pwr
RA62b
Note: Descriptions for Channel One through Channel Six are identical.
OUT 1 - 6 : 1/4” and 1/8” (3.5 mm) Tip-Ring-Sleeve jacks for connection to a
standard pair of headphones or earphones. These jac ks may be used simultaneously.
VOLUME 1 - 6: Controls the amount of output signal from the indicated channel.
MONO/STEREO SWITCH: When this switch is pressed in, the Right and Left
channels are summed together providing a mono output signal.
PAN: Controls the relative amount of signal sent to the Right and Left output
channels.
STEREO IN: 1/4” TRS input jack which parallels the rear panel Right and Left
input jacks.
POWER LED: Indicates that the RA62 is connected to the po wer supply and is
on.
REAR PANEL
62-
120 VAC
WARNING:
50/60 Hz 15 VA
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.
MADE IN U.S.A.
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
SERIAL NUMBER
MODEL RA62b
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
MAIN INPUTS
LEFT
RIGHT
RISQUE DE CHOC - NE PAS ENLEVER
AUX INPUTS
RIGHTLEFT
INSERT 6 INSERT 5 INSERT 4 INSERT 3 INSERT 2 INSERT 1
LEFT
RIGHT
120 VAC INPUT: Connects to a properly grounded AC outlet.
MAIN INPUTS: Balanced XLR jac ks f or connecting to the desired Right and Left
program material.
AUX INPUTS: 1/4” and RCA unbalanced inputs - for use in the event additional
program material is to be mixed with the main inputs, or if XLR plugs are not
available .
Note: The description for the Channel Inserts pertains to all six channels.
CHANNEL INSERTS: 1/4” TRS jacks which directly access the channel’s
heaphone output circuitry . This is a stereo jac k and requires a TRS stereo signal.
Connect the AC cord to a properly grounded ac outlet.
Determine which input configuration you will use; either discreet right/left, TRS
stereo, or mono .
For a discreet right/left input configuration, connect a balanced XLR plug contain-
ing the “Right” portion of the stereo signal to the Right Main Input. Connect a
balanced XLR plug containing the “Left” portion of the stereo signal to the Left
Input.
For a TRS stereo input configur ation, connect a Tip-Ring-Slee v e stereo plug into
the front panel STEREO IN input. This cable may come from a mixer’s headphone
output for example.
The Aux Inputs are connected in the same manner as the discreet right/left input
configuration listed above .
To send a mono signal to the RA62b, connect an XLR jack to either Main Input, or
a single 1/4” Tip-Sleeve or RCA plug into either Aux Input input and press in the
front panel MONO/STEREO switch. This mono signal will be fed to both the right
and left sides of the headphone outputs.
INSERTS
The inserts have been provided so you can directly access each headphone
output with its own program material.
The inserts
require
Tip-Ring-Slee v e connectors, with right and left signals on the
tip and ring respectively. If you use a TS mono plug - you will only hear sound out
of one side.
When these insert jacks are used, the main Right/Stereo and Left/Mono, as well
as the Aux Inputs - are disconnected. Only the stereo signals sent to the Insert
jacks go to that corresponding output.
CAUTION: Plugging a mono 1/4” TS plug into the Headphone
Outputs may cause permanent damage to the unit because
one side would be shorted to ground.
NEVER PLUG A MONO
PLUG INTO ANY OF THE HEADPHONE OUTPUTS.
Tip
Ring
Sleeve
(ground)
3
4
Loading...