Rolls PM55 User Manual
INTRODUCTION
4
Thank you for your purchase of the PM55 Stereo Personal Monitor
Amplifi er. This unit is a unique device for monitoring ones self and
program material at the same time. It has a monitor level control
and a mic level control, a mic pass-through XLR jack, earphone
and headphone output jacks, and a switchable stereo/mono 1/4"
monitor input jack.
The PM55 is designed for performers who need to monitor their
own signal, such as their vocals, with the main mix. It has become
very popular with drummers who need to mix a click track with a
monitor signal. Church choir singers love the PM55 to monitor their
voices over the musicians. And many sound technicians use the
PM55 as a quick line tester to troubleshoot audio systems.
loud personal monitoring.
... anywhere you need versatile, clear and
- Broadcast
- Live
- Studio
PM55 Personal Monitor Station
The PM55 features all these benefi ts in a convenient battery-pow-
ered package.
DESCRIPTION
lift gnd
pwr
MIC
IN
MIC
LEVEL
MONITOR
IN
ster
mon
9 - 15
+
MONITOR
LEVEL
VDC
MIC THRU: XLR jack paralleled
(hard-wired) to the MIC INPUT
jack for pass-through to a mixer
or other input device.
lift/gnd: Header jumper for connecting or disconnecting the XLR
ground (pin 1) to cassis ground.
The PM55 is confi gured at the
factory with pin 1 connected to
ground.
MIC INPUT: XLR balanced jack
for connection to a condenser or
dynamic microphone.
MONITOR INPUT: 1/4" TRS
stereo jack for connection to a line source such as a mixer monitor/
auxiliary output, cassette player output, CD player output etc.
POWER: This button turns the PM55 on and off.
BATTERY: Compartment for 9 Volt (alkaline preferred) battery.
stereo/mono: Header jumper to confi gure the Monitor input for TRS
stereo or TS mono operation. The PM55 is confi gured at the factory
in stereo mode.
9 - 15 VDC: For connection to the Rolls PS27 AC power adapter.
PHONE OUTPUTS: One 1/4" TRS stereo headphone output, one
1/8" TRS stereo earphone output.
pwr: Indicates the PM55 is on.
MIC LEVEL: Adjusts the level of signal coming from the MIC INPUT.
MONITOR LEVEL: Adjusts the level of the incoming signal from the
Monitor Input.
MIC
THRU
POWER
BATTERY
PERSONAL
MONITOR AMP
PM55
PHONES
SCHEMATIC
To view the PM55 schematic, visit our website at www.
rolls.com.
PM55 Personal Monitor Amplifi er
The PM55 is an essential monitoring tool for studio or live
applications. It allows you to mix a mic signal and a monitor signal
and hear them via headphones.
• XLR Mic In & Pass Through
• Ground lift on XLR signal
• Stereo/Mono 1/4" Monitor Input
• Headphone and earphone outputs
• Battery or AC operation
• Lots of output level, it's loud.
SPECIFICATIONS
Max Input Level: -20 dB XLR, 40 dB monitor
Input Impedance: 600 Ohm Mic,
22k Ohm Monitor
Output Impedance: 10 Ohms
Gain: 15 dB 1/4", 50 dB XLR
Bandwidth: 50 - 20 kHz
S/N Ratio: 90 dB
Power: 9 - 15 VDC
Size: 3" x 2.5" x 1.25"
(7.6 x 6 x 3.2 cm)
Weight: 1 lb (.45 Kg)
PM55
PM55
PM55
WARRANTY
For information on the Rolls One Year Limited Warranty, and
to register this product, visit our website at www.rolls.com
Rolls Corporation
Salt Lake City, UT
09/08
PM55 MONITOR
6
7 5 8 8 9 0 5 0 5 5
Rolls Bridge Clip/Jumper Wire explanation
MADE IN USA
PHANTOM
POWER
on off
OFF - POSITION
Rolls utilizes a way of switching phantom power ON and OFF thru a three pin jumper wire that is attached to the unit and a
external bridge clip to act as a switch for switching between two preset unit options. For example on other Rolls units it might
be for switching between phantom power on/off as illustrated above or it may be used for switching between ground/lift or
other options as denoted on the silk screening of the unit.
-To switch between options the Bridge clip can be moved from one option/side to the other just like a switch.
-To do this simply grab the bridge clip with a pair of needle nose pliers or tweezers and pull outward from the unit
disconnecting it from the pins of the unit completely.
-The middle pin is utilized in either position. In the above illustration (OFF) the middle pin is connected to the left side pin with
the bridge clip to have the phantom power OFF.
-To have the phantom power (ON) connect the middle pin and right pin together with the bridge clip as in the illustration below.
Please note that you must follow the silk screening of the unit to know what the jumper wire does and to which side is on or
off. All of our units are different, but great care is taken to insure that the silk screening is correct.
We use the bridge clip/jumper wire combination in place of switches due to there reliability. Switches break. Our system has
been in use for many years and we have never seen a single unit back with broken pins. We have seen many of our other
units back for repair for a simple broken switch.
We have found that customers like products better that do not break down in the field, and that they also do not like being
with out products that have to be sent back for repair. Knowing these facts we are committed to using this system in the future.
ON - POSITION
PHANTOM
POWER
MADE IN USA
on off
Loading...