Rolls MP45 User Manual

LIMITED WARRANTY

This product is warranted to the original consumer purchaser to be free from
defects in materials and workmanship under normal installation, use and service for a
period of one (1) year from the date of purchase as shown on the purchaser’s receipt.

The obligation of Rolls Corporation under this warranty shall be limited to repair
or replacement (at our option), during the warranty period of any part which proves
defective in material or workmanship under normal installation, use and service, provided
the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PRE­PAID. Products returned to us or to an authorized Service Center must be accompanied by
a copy of the purchase receipt. In the absence of such purchase receipt, the warranty
period shall be one (1) year from the date of manufacture.

This warranty shall be invalid if the product is damaged as a result of deface­ment, misuse, abuse, neglect, accident, destruction or alteration of the serial number,
improper electrical voltages or currents, repair, alteration or maintenance by any person or
party other than our own service facility or an authorized Service Center, or any use
violative of instructions furnished by us.

This one-year warranty is in lieu of all expressed warranties, obligations or
liabilities. ANY IMPLIED WARRANTIES, OBLIGA TIONS, OR LIABILITIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MER­CHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN
LIMITED WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.

IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow
the exclusion or limitation of special, incidental or consequential damages so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.

ROLLS CORPORATION

SAL T LAKE CITY, UTAH

7/02

MP45

Guitar Processor

Specifications
Input 1/4" front panel high impedance
Output Two 1/4" jacks
FX Loop stereo send and return 1/4" jacks +18dBV max
Headphone 1/4" stereo output for 16 ohms or greater
EQ 5 bands +/- 15dB 80, 240, 750, 2200, 6600 Hz
MIDI channel 1-16, omni, off; progr am changes 1-43
Chorus depth 0-100%, speed 0.1-10 sec.
Tube compliment Four stages of gain using low noise 12AX7A’s
Phantom pow er +12 vdc 50 ma on the MIDI jack pin 3, 1=gnd
Dimensions 19" X 1.75" X 10" (48 X 4.5 X 25 cm.)
Weight 7 lbs. (3.2 kg)
Accessories (optional) MP80 controller, or dual pedal controller

OWNERS MANUAL

INTRODUCTION

OPERATION

The MP45 is the culmination of a great deal of effort and has performance and convenience
features that make it absolutely unique.

* Programmable Knobs

* Programmable EQ sliders with popular center freqs.

* True non-volatile memory, no batteries to replace ever.

* Three modes of operation switch selectable

* Both MIDI and pedal controllable

* Programmable gain stages

* Headphone amp

* 43 presets in standard MIDI format (including playthrough)
Safety precautions
The MP45 has very hazardous, uninsulated voltages inside the chassis. Opening the chas­sis for any reason will void the manufacturer warranty and presents a dangerous shock
hazard. Ne v er get it wet, if an ything spills on the unit shut it off immediately and tak e it to the
dealer for service. Use of a surge protector is recommended to decrease chances of equip­ment damage by voltage surges.

The Front P anel
INPUT Plug in the instrument cord here
DRIVE 1 Adjusts the gain of the first two tube stages
DRIVE 2 Adjusts the gain of the second two tube stages, only works when
the 4 stages LED is lit
MASTER This is the master volume for the tube gain stages
PRESENCE Selects overall treble tonal characteristics
SPEED Controls the sweep speed of the chorus
DEPTH Adjusts the Depth of the stereo chorus effect, when fully CCW the
chorus is disabled
OUT LEVEL Controls the overall output level of the MP45 and is not program­mable.
HEAD PHONES This is the stereo headphone out jac k
BRITE Turns on treble boost in the tube section
4 STAGES Turns on all four tube gain stages for maximum gain
80, 240, 750, 2200, 6600 These are the boost or cut equalizer frequencies and are
used for ov erall tone control
FX LOOP Turns on the stereo effects loop which is accessed by jacks on the
rear of the unit
GA T E T urns on the automatic noise gate and need only be used for noisy
effects in the effects loop
LEARN Mode is for programming the MP45, the STORE button is active in this
mode
PLA Y This is the play through mode, all the knobs and buttons are activ e.
RECALL Mode is for calling up stored presets. The knobs and sliders are
inactive.
STOREPuts information to the memory of the MP45 and is only active in the learn
mode
UP / DOWN Switches are for cycling through the presets - not active in the PLAY
mode

The MP45 has three modes of operation LEARN, PLAY and RECALL shown by an
LED next to the label.

* The LEARN mode is for stor ing preset information in memory. Set the
knobs and buttons for the desired sound then press the store b utton, the display will
blink and the knob settings are stored in the preset number on the display. Note: the
output level knob is not programmed and is for final volume adjusting, for best re­sults this should be set at about 7 during programming. There are a total of 42
memory locations.

* In the PLAY mode the MP45 knobs work manually, the MIDI is disabled
and a footpedal can be used to turn on or off the STAGES, BRITE, FX LOOP or
GATE switches.

* The RECALL mode is for calling up stored presets, these may be ac­cessed with the front panel UP or DOWN buttons, using a MIDI controller such as
the ROLLS MP80, or a special foots witch can be used to go up or down. The presets
are numbered as MIDI program changes 1 through 42 with change number 43 show­ing as a 0 in the display . The 0 means the knobs are activ e and the MP45 is in a play
through mode on that preset. On all the other presets the knobs and sliders are
inactive since they were programmed earlier. However the buttons are still active,
even though the y come up as the y were prog rammed.

Remote control
The MP45 accepts MIDI program change information. The it may be setup to listen on any
MIDI channel or “on” for all channels or “OF” to disregard all MIDI data. The MP45 will
phantom power the MP80 footpedal and uses pin 1 for ground and pin 3 as power. In order
to use phantom power the MIDI cable must have all wires connected on the connectors. A
special dual footswitch is available that will cycle through the program numbers in RECALL
mode, or change the STAGES or FX LOOP switches in PLay mode.

Selecting a MIDI channel
The ROLLS MP45 can receive data from any of the 16 MIDI channels. The channel is pro­grammed by holding the STORE and UP buttons in at the same time the POWER switch is
turned on, while in the LEARN mode. The number in the PROGRAM display is the current
MIDI channel number. To change the MIDI channel press the UP or DOWN buttons for the
desired channel then press the STORE button to save it, turn the MP45 off. The MIDI chan­nel numbers go from 1 to 16 then to “on” meaning an y channel then to “OF” meaning no MIDI
data is recognized. The MIDI channel will be set when the unit is turned on again.

Resetting the factory presets The original factory presets may be restored by the following
procedure. In the LEARN mode hold in the UP and DOWN buttons while turning on the
POWER. An “FP” will show for a moment in the display then the number “1”. The MP45 may
now be reprogrammed or switched to another mode for use.