Rolls HR11C User Manual

LIMITED WARRANTY

This product is warranted to the original consumer purchaser to be free from
defects in materials and workmanship under normal installation, use and service for a
period of one (1) year from the date of purchase as shown on the purchaser’s receipt.

The obligation of Rolls Corporation under this warranty shall be limited to repair
or replacement (at our option), during the warranty period of any part which proves
defective in material or workmanship under normal installation, use and service, provided
the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PRE­PAID. Products returned to us or to an authorized Service Center must be accompanied by
a copy of the purchase receipt. In the absence of such purchase receipt, the warranty
period shall be one (1) year from the date of manufacture.

This warranty shall be invalid if the product is damaged as a result of deface­ment, misuse, abuse, neglect, accident, destruction or alteration of the serial number,
improper electrical voltages or currents, repair, alteration or maintenance by any person or
party other than our own service facility or an authorized Service Center, or any use
violative of instructions furnished by us.

This one-year warranty is in lieu of all expressed warranties, obligations or
liabilities. ANY IMPLIED WARRANTIES, OBLIGA TIONS, OR LIABILITIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MER­CHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN
LIMITED WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.

IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow
the exclusion or limitation of special, incidental or consequential damages so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.

HR11C

Mic Processor

ROLLS CORPORATION

SAL T LAKE CITY, UTAH

7/02

OWNERS MANUAL

Introduction

Input Level

The HR11C Mic Processor is a microphone and line level preamp f or individual
control of a signal before a main mixing console or as a single channel in a
distributes system or even as part of a single channel P.A.. Parameters under
control are high/low impedance, phantom power , compression/limiting, anti
feedback notch filter, 10 band ISO equalizer and level control. It also includes a
signal present, overload, and power LED’ s . Switches on the rear are for XLR
phantom power and MIC/line in/out. It is po wered by a 12 V AC adapter, which
contributes to its low noise level.

Applications

Ideal applications for the HR11C include amplifying acoustic instruments, control­ling podium or pulpit microphones or processing a microphone signal with a line
signal. If the HR11C is put with the R OLLS HR100 Power amplifier it makes a
useful P.A. engine with a great deal of control as might be useful in auctions,
rodeos, etc.. Since both inputs can be used at the same time one can be used for
music the other for voice such as in aerobics studios and square dance calling.

Using the HR11C

Compressor

After plugging the signal source into the input jack, push the switch to the right of
the compressor knob. The compressor is now engaged. With the knob at 0 dB it
works as a limiter, supplying no gain reduction below its threshold. It has a soft
“knee” as is hardly noticeable when engaged. As you rotate the knob toward 10
dB there is more gain for helping maintain a more constant output lev el as the
input signal is varied.

Notch Filter

The notch filter is useful for suppressing the first feedbac k fundamental. The
sound system is adjusted until there is a “threshold” of f eedback, then press the
button to the right of the notch control and adjust the control until the point where
the feedback goes a w a y. A three to ten dB increase in v olume can be achieved
this way.

10 Band Equalizer

The equalizer is mainly for adjusting the tone of the sound source f or taste or to
cut noise. In a noisy en vironment such as on stage or at a noisy location the
sliders can be adjusted to cut sounds that are not wanted. F or example if there is
loud background noise and you need only v oice frequency response then y o u
could cut all bands except the 500, 1K, and 2K for impro v ed speech clarity.

The input level is really an intermediate lev el between the head amplifier and the
processing, so it can also serve as a compressor threshold level. The HiZ input
can be used as a line input and can accept a level up to +17 dBV. The microphone
input can accept a microphone or line level depending on the MIC/LINE switch
position.

LED’ s

The PWR LED lights whenever the unit is po wered up. The SGNL lights whenever
there is a signal to the inputs, and the OUTPUT LEVEL is on. The OVLD lights
whenever there is an o v erload in the processing circuitry. There is about 6 dB of
headroom left when the OVLD lights. The limiter might be engaged to decrease
the level if necessary.

Installation

The HR11C should be installed in a clean dry environment. The 12VAC adapter
may be used or any 12VAC source supplying 300 Ma. or more may be connected
to the rear power jack. The unit may be mounted with the rac k ears supplied in a
1/2 rack standard rack or it ma y be joined with another piece with brackets to
make a 19" installation. The output of the HR11C is 50 ohms for driving line inputs
or a power amplifier directly. If mike le v el out is desired set the output switch to
MIC.

HR11C SPECIFICA TIONS

Input Impedance 1/4" 50K ohms unbalanced

XLR 50K line, 600 ohms mike balanced
Input Lev el -12 dBV max mic bal., +17 dBV line
Output Level +17 dBV balanced line, -14 dbv line
Gain Mic 60 dB max (EQ flat)

line 20 dB max (EQ flat)
Phantom Power +12 VDC
Notch Frequency 300Hz - 3000Hz adjustable
Notch Depth > 20dB
Notch Width .1 octaves or less
Compression Ratio 1/1 to 4/1
Equalizer Range + - 12 dB
Equalizer F reqs . 32Hz, 64Hz, 125Hz, 250Hz, 500Hz, 1KHz,2KHz,

4KHz, 8KHz, 16KHZ
Equalizer Filter Q 2.2
IMD .03 % (compressor out)
THD (SMPTE) .03 % (compressor out)
CMRR (low bal) 52 dB
I/O Connectors 1/4 & XLR (both in & out)
Po wer Requ. 12 VA C 50/60 Hz (adapter included)
Size 8.5" X 1.75" X 6.5" (22 X 4.5 X 17 CM)
Weight 2.5 LBS (1.14 KG)