Rollease Acmeda MTRFDCIM1C User Manual

Dry Contact Input Transmitter

DRY CONTACT

INPUT

4.33 MHz SEQUENCE

GROUP

CONTROL

1

2

1

MODE

AUTOMATE | Dry contact input transmitter enables most common mechanical switches
or automation systems relays to control ARC motorized shades. It functions as a single
channel transmitter and accepts dry contact input. Once a motor or group of motors
are paired to the transmitter, it converts the dry contact inputs and sends ARC radio
commands to trigger those motors to move upward/downward.

FEATURES:

• Interface between third party smart home systems and ARC motors

• Three dry contact inputs

• Wireless signal output

• ARC motor communication protocol

• Group Motor Control

• Four switch modes

• 12V or 24V power source compatible

MTRF-DCIM-1C_v1.0_JULY_2018

CONTENTS

1 TECHNICAL DATA / PACK CONTENTS 3

2 SAFETY 4

3 INSTALLATION 5

3.1 Overview 5

3.2 Wire Diagram 5

4 SETTING SWITCH MODE 6

5 ADDING OR DELETING A TRANSMITTER & CREATING A GROUP OF CHANNELS 7

5.1 Using motor P1 button 7

5.2 Using a pre-existing controller 7

6 SWITCH MODE OPERATION 8

6.1 Operation of Normal Switch Mode 8

6.2 Operation of Pulse Switch Mode 9

6.3 Operation of Mechanical Switch Mode 10

6.4 Operation of Sequence Switch Mode 11

6.5 Operation of Favorite Position 12

7 TROUBLESHOOTING 13

NOTES 14

2 | Automate™ Programming Instructions | MTRF-DCIM-1C ROLLEASE ACMEDA

1 TECHNICAL DATA / PACK CONTENTS

1 STATIC TITLE

TECHNICAL SPECIFICATIONS

12V Power Input Voltage: 8V ~ 16V
24V Power Input Voltage: 16V ~ 26V

Radio Frequency 433.92 MHz

Transmitting Power: 10 milliwatt

Ambient Operating

Temperature:

Transmission Distance:

Dry Contract Input Duration >0.25 seconds

PACK CONTENTS

1x contact closure box

1 x instructions

-10°C ~ 50°C
14°F ~ 122°F

up to 200m (open space)

up to 656’ (open space)

DIMENSIONS

[2 1/2"]

65mm

[1 3/4"]
45mm

[7/8"]

23mm

[1 1/2"]

37mm

3 | Automate™ Programming Instructions | MTRF-DCIM-1C ROLLEASE ACMEDA

2 SAFETY

WARNING: Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
It is important for the safety of persons to follow the enclosed instructions.

Save these instructions for future reference.

CAUTION

•

Do not expose to moisture or extreme temperatures.
Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge

•

should not be allowed to use this product.

•

Use or modification outside the scope of this instruction manual will void warranty.
Installation and programming to be performed by a suitably qualified installer.

•

•

Follow installation instructions.

•

For use with motorized shading devices.
Keep away from children.

•

•

Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
Keep clear when in operation.

•

Rollease Acmeda declares this equipment is in compliance with the essential requirements and other relevant provisions of
R&TT EC Directive 1999/5/EC.

This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning th equipment off an on, the user is
encouraged to try correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•

•

Consult the dealer or an experienced radio/TV technician for help

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

4 | Automate™ Programming Instructions | MTRF-DCIM-1C ROLLEASE ACMEDA

5005833

[2 1/2"]

65mm

[1 3/4"]

45mm

3 FUNCTIONAL OVERVIEW

3.1 Overview

STOP
DOWN
UP
COMMON
SET
LED
GROUND CONTACT
POSITIVE CONTACT 12V
POSITIVE CONTACT 24V

3.2 Wiring Diagram

+24V

+12V

GROUND

NOTE: Only one positive power point, +12V or +24V, is needed.

ROLLEASE ACMEDA Automate™ Programming Instructions | MTRF-DCIM-1C | 5