Rollease Acmeda MTDCRFTILT1, MTDCRFCL0650 User Manual

AUTOMATE

™

| VT 1.0

ARC™ VENETIAN BLIND TILT MOTOR

433 MHZ

BI-DIRECTIONAL

ELECTRONIC

LIMIT

FAVORITE
POSITION

LEVELLING

CONTROL

SELECTABLE

AUTOMATE™ | ARC™ Venetian blind motor enables motorized tilting function of most 2”
venetian blinds. Precisely control the openness of blind vanes or simply recall a favorite
position.

FEATURES:

• Electronic Limits

• 433 MHz Bi-Directional RF Communication

• Favorite Position

• 3 x Selectable Rpm

• Jog or latch & Run Modes

INSTR. MTDCRF-TILT-1 V1.0 APRIL 2017

RPM

NOTES

2 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

CONTENTS

1 ASSEMBLY 5

2 WIRING 6

2.1 Power Options 6

3 P1 BUTTON FUNCTIONS 7

3.1 Motor State Test 7

3.2 Motor Configuration Options 7

4 INTIAL SETUP 8

4.1 Pair Motor with controller 8

4.2 Check motor direction 8

4.3 Set limits 9

5 ADJUSTING LIMITS 10

5.1 Adjust upper limit 10

5.2 Adjust lower limit 10

6 ADDING OR REMOVING CONTROLLERS AND CHANNELS 11

6.1 Using motor P1 button 11

6.2 Using a pre-existing controller 11

7 FAVORITE POSITIONING 12

7.1 Set favorite position 12

7.2 Send shade to favorite position 12

7.3 Delete favorite position 12

8 SLEEP MODE 13

8.1 Enter sleep mode 13

8.2 Exit sleep mode 13

9 TROUBLESHOOTING 14

3 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

SAFTEY INSTRUCTIONS

5005833

WARNING: Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

CAUTION

• Do not expose to moisture or extreme temperatures.

• Do not allow children to play with this device.

• Use or modification outside the scope of this instruction manual will void warranty.

• Installation and programming to be performed by a suitably qualified installer.

• For use within tubular blinds.

• Ensure correct crown and drive adaptors are used for the intended system.

• Keep antenna straight and clear from metal objects

• Do not cut the antenna.

• Use only Rollease Acmeda hardware.

• Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation.

• Ensure torque and operating time is compatible with end application.

• Do not expose the motor to water or install in humid or damp environments.

• Motor is to be installed in horizontal application only.

• Do not drill into motor body.

• The routing of cable through walls shall be protected by isolating bushes or grommets.

• Ensure power cable and aerial is clear and protected from moving parts.

• If cable or power connector is damaged do not use.

Important safety instructions to be read prior to operation.

• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.

• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge

should not be allowed to use this product.

• Keep remote controls away from children.

• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.

• Keep motor away from acid and alkali.

• Do not force the motor drive.

• Keep clear when in operation.

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

4 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

1 ASSEMBLY

The Automate Venetian Blind tily motor works with most 2” blind headrail systems.

Step 1. Insert the motor / cradle assembly completely into

the drive side of the 2” headrail

Step 2. Ensure at least ½” inch of the tilting drive

Shaft is inserted into the motor.

(max depth is ¾” – Optional Shaft adapters

may be required)

Step 3. Remove motor, mark and drill hole where P1

button can be accessed.

Step 4. Reinstall motor, ensuring power cord and

Antenna extend freely from the headrail cap.

5 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

2 WIRING

2.1 Power Options

Automate DC motors are powered from a 12V DC power source. AA Battery wands, re-chargeable battery
packs and A/C power supplies are available, with a variety of quick connect extension cords. For centralized
installations, power supply range can be extended with 18/2 wire (not available through Rollease Acmeda).

• During operation, if voltage drops to less than 10V, the motor will beep 10 times to indicate a power
supply issue.

• Motor will stop running when the voltage is lower than 7V and it will resume again when the voltage is
greater than 7.5V.

DC Power Supply

Power Supply Motor

MTDCRF18-0.2 - 18mm DCRF Motor, .2N/80

MTBWAND18-25 Battery Tube for 18/25mm DCRF (no Battery) Mtrs
(inc Mt clips)

MTDCPS-18-25 Power Supply for 18/25-CL/Tilt DCRF (no Bttry) Mtr

MTBPCKR-28 Rechargeable Wand

MTDCRF25-1.1 25mm DCRF Motor, 1.1N/40r

MTDCRF-TILT-1

MTDCRF-CL-0.6-50

MTDCRF18-0.2 - 18mm DCRF Motor, .2N/80

MTDCRF25-1.1 25mm DCRF Motor, 1.1N/40r

MTDCRF-TILT-1

MTDCRF-CL-0.6-50

MTDCRF18-0.2

MTDCRF25-1.1

MTDCRFQ28-2

MTDCRF-TILT-1

MTDCRF-CL-0.6-50

Extension Cables Length

MTDC-CBLXT6 DC Battery Motor Cable extender 6” / 155mm 6 inch

MTDC-CBLXT48 DC Battery Motor Cable extender 48” / 1220mm 48 inches

MTDC-CBLXT96 DC Battery Motor Cable extender 96” / 2440mm 96 inches

Ensure cable is kept clear of fabric.

Ensure antenna is kept straight and away from metal objects.

6 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

3 P1 BUTTON FUNCTIONS

3.1 Motor State Test

This table describes the function of a short P1 button press/release(<2 seconds) depending on current motor
configuration.

P1

Press

Condition Function Achieved

Visual

Feedback

Audible

Feedback

Function Described

If limit is NOT set None No Action None No Action

Short
Press

then

Release

(<2 sec)

If limits are set

If motor is in

“Sleep Mode” &

limits are set

(Refer to Sec.10)

Operational control

of motor, run to

limit. Stop if running

Wake and control

Motor runs None

Motor

wakes and

runs in a

None

direction

Operational control

of motor after pairing

and limit setting is

completed first time

Motor is restored from

Sleep mode and RF

control is active

3.2 Motor Configuration Options

The P1 Button is utilized to administer motor configuration as described below and beginning in Section 4.

Activate Pairing

Mode

Approx.

Motor Response

Hold P1

RELEASE P1

Sleep Mode

Approx.

P1

Motor Response

RELEASE P1

7 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

Reverse
Direction

Approx.

Motor Response

RELEASE P1

Reset To Factory

Settings

Approx.

Motor Response

4 INTIAL SETUP

4.1 Pair Motor with controller

Select channel on

controller.

(Disregard if using single channel

controller)

Hold P1 button on motor Hold STOP on controller

IMPORTANT

Consult user manual for your
controller for information on

selecting channel.

Motor Response Motor Response

Motor is now in setup mode and ready for setting limits.

4.2 Check motor direction

To check travel direction of shade, press UP or

DOWN on controller.

RELEASE P1

To reverse shade direction, hold both UP

and DOWN until motor responds

Motor Reponse

Reversing motor direction using this method is
only possible during initial set-up, prior to first time limit
setting, or after a re-set of motor

8 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

4.3 Set limits

IMPORTANT

Damage to shade may occur when operating motor prior to setting limits. Attention should be given.

To save upper limit, hold UP and STOP.

Move shade to the desired highest or lowest

position by pressing the UP or DOWN buttons

on controller.

To save lower limit, hold DOWN and STOP.

Quick Press = Step

Long Press = Continuous Travel

Motor Response

Approx.

SECS

5

Initial set-up is now complete

9 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

5 ADJUSTING LIMITS

5.1 Adjust upper limit

Hold UP and STOP on Controller

until the motor responds.

Move shade to the

desired upper position

To save upper limit, hold UP and STOP until

the motor responds.

by pressing the UP or

DOWN button.

Motor Response Motor Response

Approx.

SECS

5

5.2 Adjust lower limit

Hold DOWN and STOP on

controller.

Move shade to the desired lowest

position by pressing the UP or DOWN

button

To save lower limit, hold DOWN and

STOP.

Motor Response Motor Response

Approx.

10 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

SECS

5

6 ADDING OR REMOVING CONTROLLERS AND CHANNELS

6.1 Using motor P1 button

Hold P1 button on motor head. Hold STOP on controller to add or remove

Motor Response Motor Response

RELEASE P1

Approx.

6.2 Using a pre-existing controller

A= Existing controller or channel (to keep)

B= Controller or channel or add or remove

Press P2 on existing

controller.

Motor Response Motor Response Motor Response

Press P2 on existing

controller.

Press P2 on new

controller.

IMPORTANT

Consult user manual for your

controller or sensor.

11 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

7 FAVORITE POSITIONING

7.1 Set favorite position

Move shade to the desired position by pressing the UP or DOWN button on the controller.

Press P2 on controller. Press STOP on controller. Press STOP on controller.

Motor Response Motor Response Motor Response

7.2 Send shade to favorite position

Hold STOP on controller.

Approx.

7.3 Delete favorite position

Press P2 on controller. Press STOP on controller. Press STOP on controller.

Motor Response Motor Response Motor Response

12 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

8 SLEEP MODE

8.1 Enter sleep mode

Sleep mode is utilized to prevent a motor from moving during shipping of a fabricated shade.

Hold P1 button on motor head.

Motor Response

Approx.

Motor Response

RELEASE P1

8.2 Exit sleep mode

Exit sleep mode once shade is installed.

PRESS & RELEASE P1 button on motor head.

Motor Response

Approx.

Motor Response

MOTOR RUNS TO LIMIT

13 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

9 TROUBLESHOOTING

Problem Cause Remedy

A / C power supply not plugged in.

Battery in wand are depleted Replace 8xAA alkaline batteries.

Power failure

Transmitter battery is discharged Replace battery

Battery is inserted incorrectly

Motor is not responding

Unable to adjust or set limits. Remote is in a locked state.

Cannot program a single Motor
(multiple motors respond)

into transmitter

Radio interference/shielding

Receiver distance is too far from
transmitter

Incorrect wiring

Multiple motors are paired to the
same channel.

Check motor to power cable
connection and AC plug.

Check power supply to motor is
connected and active

Check battery polarity

Ensure transmitter is positioned
away from metal objects and the
aerial on motor or receiver is kept
straight and away from metal

Move transmitter to a closer
position

Check that wiring is connected
correctly (refer to motor
installation instructions)

Change remote status to an
unlocked state

Always reserve an individual
channel for programming
functions

SYSTEM BEST PRACTICE - Provide
an extra 15 channel remote in your
multi motor projects, that provides
individual control for each motor
for programming purposes

Place all other motors into sleep
mode (ref to P1 function overview

- section 3.2 and 10.1)

14 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA

This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.

This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

ROLLEASE ACMEDA
AUSTRALIA

110 Northcorp Boulevard,
Broadmeadows VIC 3047

T [phone] | F [phone]

Queensland Branch

Unit 2/62 Borthwick Avenue,
Murarrie QLD 4172

ROLLEASE ACMEDA
USA

200 Harvard Avenue
Stamford, CT 06902 6320

T [phone] | F [phone]

ROLLEASE ACMEDA
EUROPE

Via Conca Del Naviglio 18, Milan
(Lombardia) Italy

T [phone] | F [phone]

[e-mail]
rolleaseacmeda.com

15 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor