Rollease Acmeda MTDCBRF2511, MTDCBRF4510, MTDCBRF353, MTDCRF2511, MTDCBRFQ453 User Manual
...
AUTOMATE
Li-ion ARC TUBULAR MOTOR
433 MHZ
BI-DIRECTIONAL
ELECTRONIC
LIMIT
SELECTABLE
RPM
FAVORITE
POSITION
LEVEL CONTROL WIREFREE
AUTOMATE | Li-ion ARC motors offer a wirefree rechargeable easy to use and program
solution to suit a large range of applications, torques and speeds.
The Leveling Control feature allows for precise positioning of multiple shades ensuring
perfect alignment.
Additionally, a favorite position can be pre-set and recalled at any time.
FEATURES:
• Electronic Limits
• 433 MHz Bi-Directional RF Communication
• Leveling Control
• 3 x Selectable Rpm
• Favorite Position
• Roller & Tilt Modes.
INSTR. MTDCBRF V1.2 JUNE 2016
SOLAR
POWERED
NOTES
2 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA
CONTENTS
1 ASSEMBLY 5
2 WIRING 6
2.1 Charging options 6
3 P1 BUTTON FUNCTIONS 7
4 INTIAL SETUP 8
4.1 Pair motor with controller 8
4.2 Check motor direction 8
4.3 Set limits 9
5 ADJUSTING LIMITS 10
5.1 Adjust upper limit 10
5.2 Adjust lower limit 10
6 ADDING OR REMOVING CONTROLLERS AND CHANNELS 11
6.1 Using motor P1 button 11
6.2 Using a pre-existing controller 11
7 FAVORITE POSITIONING 12
7.1 Set a favorite position 12
7.2 Send shade to favorite position 12
7.3 Delete favorite position 12
8 ADJUSTING MOTOR SPEED 13
8.1 Increase or decrease motor speed 13
9 TILT & ROLLER MODE 14
9.1 Enter tilt mode 14
9.2 Enter roller mode (Default) 14
10 TROUBLESHOOTING 15
3 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA
SAFTEY INSTRUCTIONS
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
CAUTION
• Do not expose to moisture or extreme temperatures.
• Do not allow children to play with this device.
• Use or modification outside the scope of this instruction manual will void warranty.
• Installation and programming to be performed by a suitably qualified installer.
• For use within tubular blinds.
• Ensure correct crown and drive adaptors are used for the intended system.
• Keep antenna straight and clear from metal objects
• Do not cut the antenna.
• Use only Rollease Acmeda hardware.
• Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation.
• Ensure torque and operating time is compatible with end application.
• Do not expose the motor to water or install in humid or damp environments.
• Motor is to be installed in horizontal application only.
• Do not drill into motor body.
• The routing of cable through walls shall be protected by isolating bushes or grommets.
• Ensure power cable and aerial is clear and protected from moving parts.
• If cable or power connector is damaged do not use.
Important safety instructions to be read prior to operation.
• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge
should not be allowed to use this product.
• Keep remote controls away from children.
• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
• Keep motor away from acid and alkali.
• Do not force the motor drive.
• Keep clear when in operation.
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
4 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA
1 ASSEMBLY
Please refer to Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used.
Step 1. Cut roller tube to required length.
Step 2. Ensure roller tube is clean and free from burrs.
Step 3. Fit required crown, drive and bracket adapters.
Tube must be close fitting with chosen crown
and drive adapters. Refer to Rollease Acmeda
System Assembly Manual for recommended
crown, drive, and bracket adapter kits.
Step 4. Slide Motor into tube.
Insert by aligning keyway in crown and
drive wheel to the tube.
Step 5. Mount motorized tube onto brackets.
Refer to Rollease Acmeda System
Assembly Manual for recommended crown,
drive, and bracket adapter kits.
Motor Head
Bracket
Adapter
Crown
Drive
Retaining
Clip
5 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA
Loading...